to generate one. This is was U-Boot does to generate a random MAC so we end
up with the same MAC address as if U-Boot did generate it.
MFC after: 1 week
Currently boot parameters (r0 - r3) are forgotten in ARM trampoline code.
This patch save them at startup and restore them before jumping into kernel
_start() routine.
This is usefull when booting with Linux ABI and/or custom bootloader.
Submitted by: Grégory Soutadé <soutade@gmail.com>
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D7395
- Read interrupt properties at bus enumeration time and store
it into global mapping table.
- At bus_activate_resource() time, given mapping entry is resolved and
connected to real interrupt source. A copy of mapping entry is attached
to given resource.
- At bus_setup_intr() time, mapping entry stored in resource is used
for delivery of requested interrupt configuration.
- For MSI/MSIX interrupts, mapping entry is created within
pci_alloc_msi()/pci_alloc_msix() call.
- For legacy PCI interrupts, mapping entry must be created within
pcib_route_interrupt() by pcib driver itself.
Reviewed by: nwhitehorn, andrew
Differential Revision: https://reviews.freebsd.org/D7493
Allwinner Uniprocessor SoC.
As of now it works with A10 and A13 (and possibly R8 as it is the same as the A13).
Move files.a10 into a1o subdirectory as it should be.
Rename std.a10 into std.allwinner_up
This removes the need to set the MMC pins with pullups in our DTS.
Thanks to jmcneill@ for spotting this.
Tested on Orange Pi One (Allwinner H3).
MFC after: 1 week
GPIO_INPUT/GPIO_OUTPUT.
a10_gpio_get_pud now returns the whole pud not only PULLDOWN/PULLUP.
Add a10_gpio_get_drv to get the current drive strenght.
During fdt pin configure, avoid setting function/drive/pud if it's already in
the correct value.
Tested on Allwinner H3 and A20
MFC after: 1 week
Right now, userspace (fast) gettimeofday(2) on x86 only works for
RDTSC. For older machines, like Core2, where RDTSC is not C2/C3
invariant, and which fall to HPET hardware, this means that the call
has both the penalty of the syscall and of the uncached hw behind the
QPI or PCIe connection to the sought bridge. Nothing can me done
against the access latency, but the syscall overhead can be removed.
System already provides mappable /dev/hpetX devices, which gives
straight access to the HPET registers page.
Add yet another algorithm to the x86 'vdso' timehands. Libc is updated
to handle both RDTSC and HPET. For HPET, the index of the hpet device
to mmap is passed from kernel to userspace, index might be changed and
libc invalidates its mapping as needed.
Remove cpu_fill_vdso_timehands() KPI, instead require that
timecounters which can be used from userspace, to provide
tc_fill_vdso_timehands{,32}() methods. Merge i386 and amd64
libc/<arch>/sys/__vdso_gettc.c into one source file in the new
libc/x86/sys location. __vdso_gettc() internal interface is changed
to move timecounter algorithm detection into the MD code.
Measurements show that RDTSC even with the syscall overhead is faster
than userspace HPET access. But still, userspace HPET is three-four
times faster than syscall HPET on several Core2 and SandyBridge
machines.
Tested by: Howard Su <howard0su@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
Differential revision: https://reviews.freebsd.org/D7473
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
allow us to add an ACPI attachment for arm64.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7307
The rootkey is burnt at production and can't be changed, thus is can be used
as a device unique ID or to generate a MAC address (This is was u-boot does).
The rootkey is exposed as a sysctl (dev.aw_sid.<unit>.rootkey).
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D6383
Summary:
This driver supports the following methods to trigger gathering random bits from the hardware:
1. interrupt when the FIFO is full (default) fed into the harvest queue
2. callout (when BCM2835_RNG_USE_CALLOUT is defined) every second if hz is less than 100, otherwise hz / 100, feeding the random bits into the harvest queue
If the kernel is booted with verbose enabled, the contents of the registers will be dumped after the RBG is started during the attach routine.
Author: hackagadget_gmail.com (Stephen J. Kiernan)
Test Plan: Built RPI2 kernel and booted on board. Tested the different methods to feed the harvest queue (callout, interrupt) and the interrupt driven approach seems best. However, keeping the other method for people to be able to experiment with.
Reviewed By: adrian, delphij, markm
Differential Revision: https://reviews.freebsd.org/D6888
simplebus_add_device() expect a simplebus_softc structure associated with
the device.
Add the simplebus_softc as first member in am335x_pwmss_softc structure.
Sponsored by: Rubicon Communications (Netgate)
H3 EMAC is the same as A83T/A64 except the SoC includes an (optional)
internal 10/100 PHY. Both internal and external PHYs are supported on H3
with this driver.
- Support DEVICE_POLLING
- Increase TX descriptors to 1024
- Add support for passing a chain of mbufs to if_input, reducing the
number of calls to mtx_unlock/mtx_lock under load.
- Remove duplicate byteswap when setting TX_INT_CTL in TX descriptor.
- Set undocumented "TX_NEXT_FRAME" bit in TX control 1 register.
According to the A83T BSP, setting this bit allows the DMA engine to
operate on a packet while receiving another.
Tested on A83T (1000Mbps PHY) and H3 (100Mbps PHY).
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D7031
on arm64 and all SoCs using the old FIFO register location are 32-bit only,
so unconditionally use the new location for arm64.
Reviewed by: andrew, manu
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
All armv6 processors are plenty fast enough for HZ=1000.
No changes are made for older arm systems, because some chips are a bit
wimpy for 1000 while others do fine, so it has to be set on a per-config
basis.
