operate on the resource (we have no local resources to manage); this
fixes drivers that alloc/release resources in their probe method and
then do it again in attach
o while here add some prints to catch failures and massage style a bit
o encode need for A4 bus space tag hackery according to the memory
address; checking for "uart" breaks down with the GPS chip support
which is also a uart but does not require the same hackery
o encode the correct memory window instead of carving up all of i/o
space, potentially with a larger window than a device should have;
this likely should be handled in the drivers by using a proper bus
alloc call but since some drivers depend on the bus support to figure
this out we cannot simply mod them
o add optional GPS and RS485 support (conditionally as the support
isn't ready yet)
o improves understandability by replacing numerous relative address
calculations with fixed addresses; everything should now match up
more easily with the vm layout shown at the top of the file
o move the expansion bus chip select regions to be contiguous with
the expansion bus configuration area; this is not exploited right
now but allows map consolidation in the future
o leave a gap between the expansion bus regions and the pci config
space in case we want to map more exp bus cs regions
Reviewed by: imp, thompsa
usb stack rather than with the rest of the processor support code.
Not sure that's a good idea, as we were moving away from it, but this
fixes the build in the mean time so we can have that discussion.
the same dma tag. However, it can happen multiple dma tags share the same
bounce zone too, so add a per-bounce zone map counter, and check it instead of
the dma tag map counter, to know if we have to alloc more pages.
Reported by: miwi
Reviewed by: scottl
offset. This is needed for the ehci hardware buffer rings that assume
this behavior.
This is an interim solution, and a more general one is being worked
on. This solution doesn't break anything that doesn't ask for it
directly. The mbuf and uio variants with this flag likely don't work
and haven't been tested.
Universe builds with these changes. I don't have a huge-memory
machine to test these changes with, but will be happy to work with
folks that do and hps if this changes turns out not to be sufficient.
Submitted by: alfred@ from Hans Peter Selasky's original
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)
Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.
rather than a fixed 512... This fixes the mount root problem on at91.
Prior to the SD card reorg, all data transfers were 512 bytes, so we
didn't notice.
the serial port class when we set the devclass since it is now
no-longer a compile time constant. Eliminate the pci include, as it
isn't relevant or necessary.
time constant. This allows us to potentially change it at runtime or
autodetect it early in the boot (the latter being much more likely to
have a good outcome).
o Only set 4-bit caps on those boards that have 4-bit caps (this means that
because we don't set wire4 yet, this forces us to always use 1-bit bus).
o Don't test wire4 when setting up the bus width, since bad things will
happen if we do.
# This likely won't fix the busted at91 sd card support, but these are
# needful changes for correctness.
- The contents of 'feroceon_cpufuncs' dispatch table was really dedicated for the
new Sheeva CPU (in 88F6xxx and MV-78xxx SOCs), and NOT Feroceon.
- Feroceon CPU (in 88F5xxx SOCs) appears as a regular ARM926EJ-S core and does
not require dedicated routines.
This will be accompanied by a file rename commit.
- Provide dedicated rmans for MEM and IO resources.
- Convert PCI IRQ routing info into a table (from callback approach), provide
config data for alternative DB- boards.
- Fix a wrong boundary check error in pcib_mbus_init_bar()
Obtained from: Semihalf
- Allow for setting per platform MPP/GPIO configuration in the kernel, so
that we can override all settings firmware might set.
- Set decode windows for the remaining on-chip peripherals: CESA, SATA and XOR.
- Improve handling of USB controllers so that all port are available on the
given SOC/platform (e.g. up to three on DB-78xxx), this includes rework of
USB decode windows set-up.
- Other minor fixes and cosmetics.
Obtained from: Semihalf
