palette. As a result, the colors on the video console can look rather
weird. For example, sysinstall on the alpha has a read background. We
can work around this partially by remapping the colors used by syscons for
the ANSI color escape sequences. Note that screen savers and anything that
sets the colors explicitly will still get incorrect colors, but programs
such as sysinstall will now use the correct colors. A more correct fix
would be to actually fix the VGA palette on boot by either swapping all
the red and blue attributes or by hardcoding a standard palette and
overwriting the entire palette.
Requested by: gallatin
Obtained from: NetBSD
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
This is a pretty invasive change, but there are three good
reasons to do this:
1. We'll never have > 16 bits of handle.
2. We can (eventually) enable the RIO (Reduced Interrupt Operation)
bits which return multiple completing 16 bit handles in mailbox
registers.
3. The !)$*)$*~)@$*~)$* Qlogic target mode for parallel SCSI spec
changed such that at_reserved (which was 32 bits) was split into
two pieces- and one of which was a 16 bit handle id that functions
like the at_rxid for Fibre Channel (a tag for the f/w to correlate
CTIOs with a particular command). Since we had to muck with that
and this changed the whole handler architecture, we might as well...
Propagate new at_handle on through int ct_fwhandle. Follow
implications of changing to 16 bit handles.
These above changes at least get Qlogic 1040 cards working in target
mode again. 1080/12160 cards don't work yet.
In isp.c:
Prepare for doing all loop management in outer layers.
newbus in revision 1.19. As a result, lnc was, I believe, broken
for all PCI cards. The softc fields `lnc_btag' and `lnc_bhandle'
were not initialised, `rap', `rdp' and `bdp' were initialised to
the wrong values, and the size of the DMA ring memory was calculated
incorrectly.
Paul Richards has further cleanups in the pipeline, but this at
least is enough to make the driver usable with VMware.
Approved by: paul
for selecting unit). Instead, use the resource hints mechanism.
One unfortunate situation here is that there is no resource_quad_value
function- which is what I needed for WWN boot time replacement. Worse-
you can't store the hint as just plain
hint.isp.0.nodewwn="0x50000000aaaa0001"
because this gets interpreted as an int- incorrectly because it can't
be converted to an int. I can't even get this as a string. To work
around this particular case for nodewwn && portwwn setting, this
rather grotesque form will be used:
hint.isp.0.nodewwn="w50000000aaaa0001"
hint.isp.0.portwwn="w50000000aaaa0002"
At the same time, if we have no hinted WWN, set the default WWN (which, btw,
gets overridden if the card has valid NVRAM, which is usual) to
0x400000007F000009ull (which translates to NAA == IPv4, 127.0.0.9).
Eliminate more printf's and replace them either with device_printf or
isp_prt calls.
ones where we have a CAM path) and replacing them with calls to isp_prt.,
Eliminate isp_unit references- we no longer have an isp_unit- we now
have an isp_dev that device_get_unit can work with.
CVSrepo deletion of the previous attempt will be requested:
--original message--
Add the 'virtual nulmodem driver'
Particularly useful for debuging kernels using vmware.
If your name is Bruce evans and you are a WIZ at tty interfaces,
then you should probably rip this to shreds and offer lots of suggestions and
patches. I've been using this since 4.0-CURRENT and it's never caused
problems but I'm sure I got something wrong. This is similar to the pty/cty
device driver except that both sides are ttys. Even minor numbers
are side A and odd minor numbers are side B.
Work needs to be done regarding what happens to the other side when you
close a node.
to use with vmware, configure vmware to redirect COM2 out to side A of one
of these and boot a kernel with teh gdb remote port set to sio1.
AFTER dropping into the gdb kernel debugger in your test kernel,
fire up gdb with it's remote port pointing at the appropriate side B.
To catch all console output, you can boot the vmware kernel with a serial
console, (COM1) similarly redirected to a nulmodem, and use 'tip' to observe it.
This is practically unaltered since pre 4.0 days except for
changes made along the way needed to make it compile, so any suggestions
or offers of total rewrites will be listenned to :-)
handle read and write requests for widths of multiple bytes. This
can be used to read 16-bit battery status registers for example.
- Remove some unused variables and #if 0'd debugging cruft.
- Don't complain about a GPE query that fails due to AE_NOT_FOUND if the
query method was _Q00.
from a BIF, use the size of the destinatino buffer, not the length of the
string to determine where to put the nul char. As a side effect, the
old code would truncate the string by one character while it was possibly
overflowing the buffer.
o Allocate memory mapped by pcic even when not used for ncv.
This is for PC-Cards which needs offset, because I/O space should not be
used by other devices.
Pointed-out-by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
If you ever want to run midi(4) out of the giant lock, uncomment
MIDI_OUTOFGIANT in midi.h. Confirmed to work for csamidi with WITNESS
and INVARIANTS.
- midi_info, midi_open and seq_info are now tailqs, allowing arbitrary
numbers of devices to be configured.
- Do not send an active sensing message to reset midi modules.
- Clone /dev/sequencer*. /dev/sequencer0 and /dev/sequencer are generated
upon initialization.
- Convert to a more efficient queueing implementation.
- Don't allocate command buffers on the fly; simply work from a
static pool.
- Add a control device interface, for later use.
- Handle controller overload better as a consequence of the
improved queue implementation.
- Add support for the XPT_GET_TRAN_SETTINGS ccb, and correctly
set the virtual SCSI channels up for multiple outstanding I/Os.
- Update copyrights for 2001.
- Some whitespace fixes to improve readability.
Due to a misunderstanding on my part, previous versions of the
driver were limited to a single outstanding I/O per virtual drive.
Needless to say, this update improves performance substantially.
