Commit Graph

3 Commits

Author SHA1 Message Date
Marius Strobl
72dec0792a - Add support for eMMC "partitions". Besides the user data area, i. e.
the default partition, eMMC v4.41 and later devices can additionally
  provide up to:
  1 enhanced user data area partition
  2 boot partitions
  1 RPMB (Replay Protected Memory Block) partition
  4 general purpose partitions (optionally with a enhanced or extended
    attribute)

  Of these "partitions", only the enhanced user data area one actually
  slices the user data area partition and, thus, gets handled with the
  help of geom_flashmap(4). The other types of partitions have address
  space independent from the default partition and need to be switched
  to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".

  The second kind of these "partitions" doesn't fit that well into the
  design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
  of these "partitions" up as disk(9)'s (except for the RPMB partition
  as it didn't seem to make much sense to be able to put a file-system
  there and may require authentication; therefore, RPMB partitions are
  solely accessible via the newly added IOCTL interface currently; see
  also below). This approach for one resulted in cleaner code. Second,
  it retains the notion of mmcsd(4) children corresponding to a single
  physical device each. With the addition of some layering violations,
  it also would have been possible for mmc(4) to add separate mmcsd(4)
  instances with one disk each for all of these "partitions", however.
  Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
  issuing CMD6, which has been factored out into mmc_subr.c.

  Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
  code in the boot partitions etc., another use case for the partition
  support is the activation of pseudo-SLC mode, which manufacturers of
  eMMC chips typically associate with the enhanced user data area and/
  or the enhanced attribute of general purpose partitions.

  CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.

- Now that properly issuing CMD6 is crucial (so data isn't written to
  the wrong partition for example), make a step into the direction of
  correctly handling the timeout for these commands in the MMC layer.
  Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
  recommended by relevant specifications. However, quite some work is
  left to be done in this regard; all other R1B-type commands done by
  the MMC layer also should be followed by a SEND_STATUS (CMD13), the
  erase timeout calculations/handling as documented in specifications
  are entirely ignored so far, the MMC layer doesn't provide timeouts
  applicable up to the bridge drivers and at least sdhci(4) currently
  is hardcoding 1 s as timeout for all command types unconditionally.
  Let alone already available return codes often not being checked in
  the MMC layer ...

- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
  with Linux so that the GNU mmc-utils can be ported to and used with
  FreeBSD (note that due to the remaining deficiencies outlined above
  SANITIZE operations issued by/with `mmc` currently most likely will
  fail). These latter will be added to ports as sysutils/mmc-utils in
  a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
  partitioning eMMC devices (tested working).

- For devices following the eMMC specification v4.41 or later, year 0
  is 2013 rather than 1997; so correct this for assembling the device
  ID string properly.

- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
  least for some of the above a matching pair is required.

- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
  controllers as such in order to match the PCI one.
  Additionally, in the entry for the 80860F14 SDXC controller remove
  the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.

OKed by:	imp
Submitted by:	ian (mmc_switch_status() implementation)
2017-03-16 22:23:04 +00:00
Enji Cooper
193d9e768b sys/modules: normalize .CURDIR-relative paths to SRCTOP
This simplifies make output/logic

Tested with:	`cd sys/modules; make ALL_MODULES=` on amd64
MFC after:	1 month
Sponsored by:	Dell EMC Isilon
2017-03-04 10:10:17 +00:00
Warner Losh
84ee9401a3 Loadable modules for mmc (the bus) amd mmcsd (the MMC and SD support
code).  A little green, so not yet connected to the build.
2006-10-20 06:52:59 +00:00