Commit Graph

22 Commits

Author SHA1 Message Date
Gleb Smirnoff
61a3ac6e27 The MII layer shouldn't care about administrative status of an
interface. Make MII drivers forget about 'struct ifnet'.

Later plan is to provide an administrative downcall from ifnet
layer into drivers, to inform them about administrative status
change. If someone thinks that processing MII events for an
administratively down interface is a big problem, then drivers
would turn MII processing off.

The following MII drivers do evil things, like strcmp() on
driver name, so they still need knowledge of ifnet and thus
include if_var.h. They all need to be fixed:

sys/dev/mii/brgphy.c
sys/dev/mii/e1000phy.c
sys/dev/mii/ip1000phy.c
sys/dev/mii/jmphy.c
sys/dev/mii/nsphy.c
sys/dev/mii/rgephy.c
sys/dev/mii/truephy.c

Sponsored by:	Netflix
Sponsored by:	Nginx, Inc.
2013-10-26 18:40:17 +00:00
Marius Strobl
604f5f1f77 Use DEVMETHOD_END. 2011-11-23 20:27:26 +00:00
Marius Strobl
3fcb7a5365 - Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
  it might provide useful for debugging). For most mii(4) drivers it
  was unclear whether the PHYs driven by them actually support
  loopback or not. Moreover, typically loopback mode also needs to
  be activated on the MAC, which none of the Ethernet drivers using
  mii(4) implements. Given that loopback media has no real use (and
  obviously hardly had a chance to actually work) besides for driver
  development (which just loopback mode should be sufficient for
  though, i.e one doesn't necessary need support for loopback media)
  support for it is just dropped as both NetBSD and OpenBSD already
  did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
  instead of discrete function pointers, and extend this to include
  a "reset" entry point. Make sure any PHY-specific reset routine is
  always used, and provide one for lxtphy(4) which disables MII
  interrupts (as is done for a few other PHYs we have drivers for).
  This includes changing NIC drivers which previously just called the
  generic mii_phy_reset() to now actually call the PHY-specific reset
  routine, which might be crucial in some cases. While at it, the
  redundant checks in these NIC drivers for mii->mii_instance not being
  zero before calling the reset routines were removed because as soon
  as one PHY driver attaches mii->mii_instance is incremented and we
  hardly can end up in their media change callbacks etc if no PHY driver
  has attached as mii_attach() would have failed in that case and not
  attach a miibus(4) instance.
  Consequently, NIC drivers now no longer should call mii_phy_reset()
  directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
  The purpose of that function is to perform the common steps to attach
  a PHY driver instance and to hook it up to the miibus(4) instance and to
  optionally also handle the probing, addition and initialization of the
  supported media. So all a PHY driver without any special requirements
  has to do in its bus attach method is to call mii_phy_dev_attach()
  along with PHY-specific MIIF_* flags, a pointer to its PHY functions
  and the add_media set to one. All PHY drivers were updated to take
  advantage of mii_phy_dev_attach() as appropriate. Along with these
  changes the capability mask was added to the mii_softc structure so
  PHY drivers taking advantage of mii_phy_dev_attach() but still
  handling media on their own do not need to fiddle with the MII attach
  arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
  for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
  structure. Several PHY drivers require this information also after
  attaching and previously had to wrap their own softc around mii_softc.
  NetBSD/OpenBSD also keep track of the model and revision on their
  mii_softc structure. All PHY drivers were updated to take advantage
  as appropriate.
- Convert the mebers of the MII data structure to unsigned where
  appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
  when mapping an OUI to the MII ID registers. All PHY drivers and
  miidevs where changed as necessary. Actually this now again allows to
  largely share miidevs with NetBSD, which fixed this problem already
  9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
  weren't explicitly converted to support flow control before. It's
  unclear whether flow control actually works with these but typically
  it should and their net behavior should be more correct with these
  changes in place than without if the MAC driver sets MIIF_DOPAUSE.

Obtained from:	NetBSD (partially)
Reviewed by:	yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
Marius Strobl
a16ce54ca6 - Also probe BCM5214 and BCM5222.
- Add some DSP init code for BCM5221. The values derived from Apple's GMAC
  driver and the same init code also exists in Linux's sungem_phy driver.
- Only read media status bits when they are valid.

Obtained from:	NetBSD, OpenBSD
2010-11-22 22:03:11 +00:00
Marius Strobl
4b9b1e1163 Add support for flow control.
Obtained from:	NetBSD (partially)
2010-11-22 21:24:29 +00:00
Marius Strobl
8e5d93dbb4 Convert the PHY drivers to honor the mii_flags passed down and convert
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
  addresses; we now let mii_attach() only probe the PHY at the desired
  address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
  off from, partly even based on grabbing and using the softc of the
  parent; we now pass these flags down from the NIC to the PHY drivers
  via mii_attach(). This got us rid of all such hacks except those of
  brgphy() in combination with bce(4) and bge(4), which is way beyond
  what can be expressed with simple flags.

While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).

Reviewed by:	jhb, yongari
2010-10-15 14:52:11 +00:00
Marius Strobl
d7a9ad5688 Consistently always explicitly set IFM_HDX for half-duplex.
Obtained from:	OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
Marius Strobl
de1add1e45 - In the spirit of previous simplifications factor out the checks for a
different PHY instance being selected and isolation out into the wrappers
  around the service methods rather than duplicating them over and over
  again (besides, a PHY driver shouldn't need to care about which instance
  it actually is).
- Centralize the check for the need to isolate a non-zero PHY instance not
  supporting isolation in mii_mediachg() and just ignore it rather than
  panicing, which should sufficient given that a) things are likely to
  just work anyway if one doesn't plug in more than one port at a time and
  b) refusing to attach in this case just leaves us in a unknown but most
  likely also not exactly correct configuration (besides several drivers
  setting MIIF_NOISOLATE didn't care about these anyway, probably due to
  setting this flag for no real reason).
- Minor fixes like removing unnecessary setting of sc->mii_anegticks,
  using sc->mii_anegticks instead of hardcoded values etc.
2010-10-02 18:53:12 +00:00
Marius Strobl
7b9a15f73c Use the mii_data provided via mii_attach_args and mii_pdata respectively
instead of reaching out for the softc of the parent.
2010-09-27 20:31:03 +00:00
Marius Strobl
485fc5eb4e - Remove clause 3 and 4 from TNF licenses.
- Remove closes 3 & 4 from Manuel Bouyer's license.

Obtained from:	NetBSD
2010-09-26 22:11:41 +00:00
Marius Strobl
a35b933378 Add a helper function mii_phy_dev_probe(), which wraps around the
mii_phy_match() API and takes care of the PHY device probe based on
the struct mii_phydesc array and the match return value provided.
Convert PHY drivers to take advantage of mii_phy_dev_probe(),
converting drivers to provide a mii_phydesc table in the first
place where necessary.

Reviewed by:	yongari
MFC after:	2 weeks
2006-12-02 15:32:34 +00:00
Marius Strobl
9475e904d6 Analogous to mii_add_media(), factor out the code for checking whether
the BMSR contains any media at all to mii_phy_add_media(). The majority
of the drivers currently using mii_phy_add_media() were missing such a
check anyway though.

MFC after:	2 weeks
2006-11-27 23:50:19 +00:00
Pyun YongHyeon
5358725ab4 Replace hard-coded magic constants to system defined constants
(BUS_PROBE_DEFAULT, BUS_PROBE_GENERIC etc).
There is no functional changes.

Reviewed by:	oleg, scottl
2006-07-03 02:53:40 +00:00
Warner Losh
098ca2bda9 Start each of the license/copyright comments with /*-, minor shuffle of lines 2005-01-06 01:43:34 +00:00
Poul-Henning Kamp
41ee9f1c69 Add some missing <sys/module.h> includes which are masked by the
one on death-row in <sys/kernel.h>
2004-05-30 17:57:46 +00:00
Marius Strobl
50aa106108 Remove double __FBSDID and move the remaining one into a common place after
the license(s) and before the driver comment (the latter only in drivers not
having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
Bill Paul
b9f78d2b4a Add a device driver for the Broadcom BCM4401 ethernet controller,
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.

The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.

This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
2003-09-09 18:17:23 +00:00
David E. O'Brien
aad970f1fe Use __FBSDID().
Also some minor style cleanups.
2003-08-24 17:55:58 +00:00
Poul-Henning Kamp
19ca58475e Remove unnecessary breaks.
Remove unused variables.
Add XXX comment where a break may be missing. [lxtphy.c]

Found by:       FlexeLint
2003-05-31 19:48:33 +00:00
David E. O'Brien
2d3ce7133a Remove miidevs.h and generate it from miidevs at compile time.
The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
Semen Ustimenko
07971c4102 Remove unnecessary <sys/malloc.h> include.
Submitted by:	marius@alchemy.franken.de
MFC after:	1 week
2002-10-29 00:20:47 +00:00
Benno Rice
d82bc4fba8 Add a driver for the Broadcom BCM52xx "mini-theta" PHY. This includes the
internal PHY on the 3COM 3C905B and 3C905C parts, however I've rigged it so
that xlphy (aka exphy) takes precedence for the time being.

If people try this with their xl cards and decide that it's a better choice,
we can switch this later.

This is the PHY used in various iMacs and possibly other GMAC-equipped
Macintoshes with 10/100 PHYs (the ones with 10/100/1000 appear to use brgphy).

Obtained from:	NetBSD
2002-07-05 11:07:24 +00:00