- Factor out common part to zynq-7000.dtsi
- Fix problem with Zynq interrupts by using interrupt "triples"
in .dtsi file to differentiate between edge-triggered and
level-triggered interrupts
- cgem driver now recognizes "status" property
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D6095
a child of it. This is done in conformity with Linux dts files and
as preparation for rework of BCM2836 interrupt controller for INTRNG.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D5807
The following pheripherals are supported: UART, MMC, AHCI, EHCI, PCIe, I2C,
PMIC, GPIO, CPU temperature and clock.
Note: The PCIe driver is pure mash at this moment. It will be reworked
immediately when both D5237 and D2579 enter the current tree.
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202
dts files. It may be removed once it will be fixed upstream.
This is done just to supresses a warning during dtb evaluation as
there is no elm driver in tree at present.
least the audio codec driver currently in review.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5050
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
Invalid (in FreeBSD) definition of PCI controller was
replaced with another one, working in FreeBSD environment.
PCI controller's entry had to move from its parent node
so as to be recognized properly by FBSD.
PCI was enabled in kernel configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4379
uart_dev_ns8250 now relies on compatible property instead of additional
'busy-detect' cell. All drivers with compatible = "snps,dw-apb-uart" have
busy detection turned on. DTS files of devices affected by the change
were modified and 'busy-detect' property was removed.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4218
Ranges property of 'soc' node used two-cell addresses which resulted in
casting errors as simplebus resource allocation works with 32-bit u_long
variables. FDT ranges were simplified.
Reviewed by: imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4212
This commit introduces initial support for Marvell Armada38x platform.
Changes:
- Add common DTS files for Armada38x SoCs and DTS file for A388-GP
- Add ARMADA38X kernel configuration
- Add option SOC_MV_ARMADA38X and set MV_PCI_PORTS
- Add list of files to compile
- Implement get_tclk(), get_sar_value(), cpu_reset() functions
- Add CPU ID and SoC numbers
- Correct ifdefs in arm/mv/timer.c
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4210
Zybo needs its own DTB and has a different PHY, so add it to
the base kernel. Details on building bootable SD images at
http://www.thomasskibo.com/zedbsd/
Submitted By: Thomas Skibo
so they were disabled during DTS transition. Though there are
no standard devices/drivers on them people might use iic(4) userland
interface to access these buses.
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
based device.
Following u-boot commands allow FreeBSD boot on
Yiyate Android TV Box (aml8726-m3):
tv open 480p
mmc rescan 0
fatload mmc 0 0x80100000 kernel.bin
go 0x80100000
The current FreeBSD driver doesn't program the video
clocks so the u-boot tv command is necessary in order
for the frame buffer to be useful (otherwise it can
be skipped).
The SD card for the Yiyate Android TV Box doesn't need
anything special beyond creating a FAT16 and a UFS
filesystem.
Differential Revision: https://reviews.freebsd.org/D2636
Submitted by: John Wehle
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is based on the patch sent by Alexander Fedorov with the following
fixes/improvements:
- Better error handling;
- Clock is derived from PLL6 (obtained from netbsd);
- No more unnecessary busy loops on interrupt handler;
- style(9) fixes and code cleanup.
I also want to thanks Martin Galvan who has sent an alternative
implementation with some interesting fixes.
Tested on CubieBoard2, Banana-Pi (thanks to netgate!) and Cubieboard1
(Pratik Singhal).
This is intended to pave the way for the upcoming GSoC work (and make
easier the build of images for the supported boards).
PR: 196081
Submitted by: Alexander Fedorov <alexander.fedorov@rtlservice.com>
determined at runtime so there's no need to set the values in
each DTS.
Tested on YYHD18 (aml8726-m3), VSATV102 (aml8726-m6), and
ODROIDC1 (aml8726-m8b).
Differential Revision: https://reviews.freebsd.org/D2588
Submitted by: John Wehle
The Alpine Platform-On-Chip offers multicore processing
(quad ARM Cortex-A15), 1/10Gb Ethernet, SATA 3, PCI-E 3,
DMA engines, Virtualization, Advanced Power Management and other.
This code drop involves basic platform support including:
SMP, IRQs, SerDes, SATA. As of now it is missing the PCIe support.
Part of the functionality is provided by the low-level code (HAL)
delivered by the chip vendor (Annapurna Labs) and is a subject to
change in the future (is planned to be moved to sys/contrib directory).
The review log for this commit is available here:
https://reviews.freebsd.org/D2340
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Annapurna Labs
The 'pwr' LED is connected to GPIO pin 35 (active high) and the 'act' LED
is connected to GPIO pin 47 (active high).
Remove the GPIO pin 47 from reserved pins list, previously it was used to
signaling the SD Card presence and now it is used by act LED.
