integer expression. Otherwise the sizeof() call will force the expression
to be evaluated as unsigned, which is not the intended behavior.
Obtained from: NetBSD (in a different form)
code retransmitting data from the wrong offset.
As a footnote, the newreno code was partially derived from NetBSD
and Tom Henderson <tomh@cs.berkeley.edu>
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
better recovery for multiple packet losses in a single window.
The algorithm can be toggled via the sysctl net.inet.tcp.newreno,
which defaults to "on".
Submitted by: Jayanth Vijayaraghavan <jayanth@yahoo-inc.com>
calling in_pcbbind so that in_pcbbind sees a valid address if no
address was specified (since divert sockets ignore them).
PR: 17552
Reviewed by: Brian
to PPTP) with more generic PacketAliasRedirectProto().
Major number is not bumped because it is believed that noone
has started using PacketAliasRedirectPptp() yet.
LSNAT links are first created by either PacketAliasRedirectPort() or
PacketAliasRedirectAddress() and then set up by one or more calls to
PacketAliasAddServer().
Without this fix, all IPv6 TCP RST packet has wrong cksum value,
so IPv6 connect() trial to 5.0 machine won't fail until tcp connect timeout,
when they should fail soon.
Thanks to haro@tk.kubota.co.jp (Munehiro Matsuda) for his much debugging
help and detailed info.
connections, after SYN packets were seen from both ends. Before this,
it would get applied right after the first SYN packet was seen (either
from client or server). With broken TCP connection attempts, when the
remote end does not respond with SYNACK nor with RST, this resulted in
having a useless (ie, no actual TCP connection associated with it) TCP
link with 86400 seconds TTL, wasting system memory. With high rate of
such broken connection attempts (for example, remote end simply blocks
these connection attempts with ipfw(8) without sending RST back), this
could result in a denial-of-service.
PR: bin/17963
but with `dst_port' work for outgoing packets.
This case was not handled properly when I first fixed this
in revision 1.17.
This change is also required for the upcoming improved PPTP
support patches -- that is how I found the problem.
Before this change:
# natd -v -a aliasIP \
-redirect_port tcp localIP:localPORT publicIP:publicPORT 0:remotePORT
Out [TCP] [TCP] localIP:localPORT -> remoteIP:remotePORT aliased to
[TCP] aliasIP:localPORT -> remoteIP:remotePORT
After this change:
# natd -v -a aliasIP \
-redirect_port tcp localIP:localPORT publicIP:publicPORT 0:remotePORT
Out [TCP] [TCP] localIP:localPORT -> remoteIP:remotePORT aliased to
[TCP] publicIP:publicPORT -> remoteIP:remotePORT
INADDR_NONE: Incoming packets go to the alias address (the default)
INADDR_ANY: Incoming packets are not NAT'd (direct access to the
internal network from outside)
anything else: Incoming packets go to the specified address
Change a few inaddr::s_addr == 0 to inaddr::s_addr == INADDR_ANY
while I'm there.
redirected and when no target address has been specified, NAT
the destination address to the alias address rather than
allowing people direct access to your internal network from
outside.
mbuf is marked for delayed checksums, then additionally mark the
packet as having it's checksums computed. This allows us to bypass
computing/checking the checksum entirely, which isn't really needeed
as the packet has never hit the wire.
Reviewed by: green
Reported in Usenet by: locke@mcs.net (Peter Johnson)
While i was at it, prepended a 0x to the %D output, to make it clear that
the printed value is in hex (i assume %D has been chosen over %#x to
obey network byte order).
improperly doing the equivalent of (m = (function() == NULL)) instead
of ((m = function()) == NULL).
This fixes a NULL pointer dereference panic with runt arp packets.
Remove a bogus (redundant, just weird, etc.) key_freeso(so).
There are no consumers of it now, nor does it seem there
ever will be.
in6?_pcb.c:
Add an if (inp->in6?p_sp != NULL) before the call to
ipsec[46]_delete_pcbpolicy(inp). In low-memory conditions
this can cause a crash because in6?_sp can be NULL...
from iso88025.h.
o Add minimal llc support to iso88025_input.
o Clean up most of the source routing code.
* Submitted by: Nikolai Saoukh <nms@otdel-1.org>
Now most big problem of IPv6 is getting IPv6 address
assignment.
6to4 solve the problem. 6to4 addr is defined like below,
2002: 4byte v4 addr : 2byte SLA ID : 8byte interface ID
The most important point of the address format is that an IPv4 addr
is embeded in it. So any user who has IPv4 addr can get IPv6 address
block with 2byte subnet space. Also, the IPv4 addr is used for
semi-automatic IPv6 over IPv4 tunneling.
With 6to4, getting IPv6 addr become dramatically easy.
The attached patch enable 6to4 extension, and confirmed to work,
between "Richard Seaman, Jr." <dick@tar.com> and me.
Approved by: jkh
Reviewed by: itojun
