from the sdl because strlcpy requires that the source string be
NUL-terminated unlike strncpy.
Submitted by: Peter Jeremy <PeterJeremy at optushome dot com dot au>
name.
Prevent the kernel from potentially overflowing the interface name
variable. The size argument of strlcpy is complex because the name is
not null-terminated in sdl_data.
and to make sure that we catch oversized arguments rather than silently
truncate them. I dont know if sscanf will reject an integer if it will
not fit in the short return variable or not, but this way it should be
detected.
regarding 802.1 MAC and Mandatory Access Control (MAC). Some
potential for confusion remains further in other areas of the
system regarding Message Authentication Codes (MAC).
Requested by: wollman
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
interfaces using the 'mac' argument. Without MAC support in the
kernel, this does not change the behavior of ifconfig.
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
Setting this flag on an ethernet interface blocks transmission of packets
and discards incoming packets after BPF processing.
This is useful if you want to monitor network trafic but not interact
with the network in question.
Sponsored by: http://www.babeltech.dk
Also, for all interfaces in this mode pass all ethernet frames to upper layer,
even those not addressed to our own MAC, which allows packets encapsulated
in those frames be processed with packet filters (ipfw(8) et al).
Emphatically requested by: Anton Turygin <pa3op@ukr-link.net>
Valuable suggestions by: fenner
that could be used to set/get arbitrary length link level
addresses. Alias "lladdr" parameter and "ether" family
to the new "link" family for backward compatibility.
PR: bin/31476
MFC after: 1 week
It does not help modern compilers, and some may take some hit from it.
(I also found several functions that listed *every* of its 10 local vars with
"register" -- just how many free registers do people think machines have?)
index, then retrieve statistics for that index, rather than retrieving
all interfaces and then looking for a matching name. This allows the
user to refer to an interface via an alias name.
While I'm here, also perform a few assorted cleanups.
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
printed on a single, very long, and generally unreadable line. This
isn't very useful. It's also really ugly and most of the time you don't
care what media is supported anyway.
PR: 27701
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
This allows you to set ether addresses with 'ifconfig ether'. Also, use
some saner socket address families that allow several special case tests
to be removed.
address on an interface. This basically allows you to do what my
little setmac module/utility does via ifconfig. This involves the
following changes:
socket.h: define SIOCSIFLLADDR
if.c: add support for SIOCSIFLLADDR, which resets the values in
the arpcom struct and sockaddr_dl for the specified interface.
Note that if the interface is already up, we need to down/up
it in order to program the underlying hardware's receive filter.
ifconfig.c: add lladdr command
ifconfig.8: document lladdr command
You can now force the MAC address on any ethernet interface to be
whatever you want. (The change is not sticky across reboots of course:
we don't actually reprogram the EEPROM or anything.) Actually, you
can reprogram the MAC address on other kinds of interfaces too; this
shouldn't be ethernet-specific (though at the moment it's limited to
6 bytes of address data).
Nobody ran up to me and said "this is the politically correct way to
do this!" so I don't want to hear any complaints from people who think
I could have done it more elegantly. Consider yourselves lucky I didn't
do it by having ifconfig tread all over /dev/kmem.
Improve compatibility with BSD/OS, and also more accurately reflect that
IP aliases aren't really any different than the primary IP address on an
interface.
Reviewed by: dcs
Approved by: jkh
IPv6 scoped addr display is not yet supported by ifconfig
and route. Now almost of IPv6 apps support it, so its support
in ifconfig and route is important to keep consisetncy, and
to avoid user confusion.
Approved by: jkh
packet divert at kernel for IPv6/IPv4 translater daemon
This includes queue related patch submitted by jburkhol@home.com.
Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
we're about to operate on, try to load one. Don't complain if the
load fails, and always press on regardless (there may not be a module
suitable or required).
With the renaming of the PCI ethernet driver modules and the addition
of appropriate miibus dependancies on those modules that need it, it is
now no longer necessary to compile many ethernet drivers into the kernel;
they will be loaded on demand the first time they are ifconfig'ed.
Inspiration from: mount
Reviewed by: obrien