adding it to the nice tables. Therefore, in kseq_add_nice, we should
keep in mind that the load will be 1 if we are the only thread, and not
0.
- Assert that the sched lock is held in all the appropriate places.
- Increase the scope of the sched lock in sched_pctcpu_update().
- Hold the sched lock in sched_runnable(). It is not held by the caller.
ia64-specific.
- When trying to re-route interrupts, don't change cfg->intline if the
re-route fails by returning an invalid vector. This fixes machines
without any way of routing interrupts such as older PC's without a
$PIR table.
We do not currently write the new intline value back to the hardware, but
we should. That will likely be added in a later commit.
the caller assumes this to not happen by means of performing an
indirection without checking the return value. Add KASSERTs to
force a kernel with INVARIANTS to panic. This is a short-term
measure. The pmap code is scheduled to be overhauled.
to deliver a signal and the RSE backing store has been exhausted or
the backing store pointer has been clobbered, we need to make sure
we call userret() and do_ast() when we exit from trap(). Not adjusting
the local variable 'user' in this case will prevent the faulty process
from being terminated and we end up in an infinite fault repetition.
Faulty process provided by: bento
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
aic7xxx.c:
aic7xxx.h:
aic7xxx_pci.c:
Switch ah?_reset() to take an additional "reinit" argument.
Use this instead of init_level to determin if the chip
should be fully reinitialized after a chip reset. This
is required so that ah?_shutdown() can reset the chip
without side-effects.
aic79xx.c:
Implement ahd_suspend() and ahd_resume().
aic7xxx.c:
Change ahc_loadseq() to *not* restart the sequencer.
This brings the loadseq behavior in line with that
of the 7902 driver and also simplifies the init routine.
Correct the resume routine to enable interrupts and
restart the sequencer.
always kernel space. It should be treated as user space when run with
user privileges (which is the case for the signal trampolines). This
fixes its only use in a KASSERT in subr_trap.c.
fit on one line. Account for threads better.
* No need to report that it is on a sleep queue if it is actually sleeping
* "Normal" state is almost ubiquitous.. only report abnormal states.
* increment the #lines count for each separate thread shown in threaded
programs.
makes it less likely that a threaded program will make all the data
on a screen overflow off the top of the screen.
while after the legacy device was added since this driver hangs from
legacy and not nexus.
- Make several methods non-static so they can be reused in a mptable
host -> pci bridge driver that will be added at a later date.
- Let legacy_pcib() use pcibios_pcib_route_interrupt() directly instead of
wrapping it in a private function. Originally, I thought I was going to
have the nexus_pcib() driver make a runtime APIC vs. 8259A check and call
the appropriate routing method (MPTable vs. PIR) that way, but it ended
up being cleaner to make nexus_pcib() just work with PIR and have a
separate host -> pci bridge driver for the mptable/apic case.
bridge lives on (i.e., the parent bus) when probing the PIR table for a
bus. This could cause the PCIBIOS PCI-PCI bridge driver to bogusly attach
to bridges that weren't in the PIR but whose parent bus was in the PIR.
obtained from o2micro. These should only be needed for 'older'
o2micro bridges (anything before the 7xxx series of bridges), but will
work with the new bridges.
# I don't plan on porting it to oldcard, but will happily commit to
# oldcard if someone else needs them.
Add sysctl's to display statistics/debug_info
Set WAIT_FOR_AUTONEG_DEFAULT to zero by default
Increment packet in/out statistics inline instead of every two seconds.
MFC after: 3 days
attribute name of "" from ffs_getextattr(). Invoking VOP_GETETATTR()
with an empty name is now no longer supported; user application
compatibility is provided by a system call level compatibility
wrapper. We make sure to explicitly reject attempts to set an EA
with the name "".
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
"", temporarily map it to a call to extattr_list_vp() to provide
compatibility for older applications using the "" API to retrieve
EA lists.
Use VOP_LISTEXTATTR() to support extattr_list_vp() rather than
VOP_GETEXTATTR(..., "", ...).
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Asssociates Laboratories
specific attribute name. It will have the same semantics as the
older vop_getextattr() "retrieve the names" hack, returning
a buffer with ASCII nul-seperated names.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
extended attribute retrieval code: it's no longer special-cased,
and is caught by the normal UFS1 EA validity checks (and, in
fact, returns the same error, EINVAL).
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
we were passing in a void* representing the PCB of the parent thread.
Now we pass a pointer to the parent thread itself.
The prime reason for this change is to allow cpu_set_upcall() to copy
(parts of) the trapframe instead of having it done in MI code in each
caller of cpu_set_upcall(). Copying the trapframe cannot always be
done with a simply bcopy() or may not always be optimal that way. On
ia64 specifically the trapframe contains information that is specific
to an entry into the kernel and can only be used by the corresponding
exit from the kernel. A trapframe copied verbatim from another frame
is in most cases useless without some additional normalization.
Note that this change removes the assignment to td->td_frame in some
implementations of cpu_set_upcall(). The assignment is redundant.
A previous call to cpu_thread_setup() already did the exact same
assignment. An added benefit of removing the redundant assignment is
that we can now change td_pcb without nasty side-effects.
This change officially marks the ability on ia64 for 1:1 threading.
Not tested on: amd64, powerpc
Compile & boot tested on: alpha, sparc64
Functionally tested on: i386, ia64
got fixed two weeks after the ia64 version was copied from the alpha
version (see rev 1.32 of sys/alpha/alpha/mem.c). As such, we were
missing the same continue as on alpha.
While here, add a default case for the device minor switch and do
some general style(9) cleanups.
WARNING: this file still has bugs. When reading from region 6 or
region 7, we don't validate the physical address. One can trivially
cause a machine check by trying to read from address 0xFFFFFFFFFFFFFFF0
or something that uses the unimplemented physical address bits.
Reported by: Alan Robinson <alan.robinson@fujitsu-siemens.com>
we were passing in a void* representing the PCB of the parent thread.
Now we pass a pointer to the parent thread itself.
The prime reason for this change is to allow cpu_set_upcall() to copy
(parts of) the trapframe instead of having it done in MI code in each
caller of cpu_set_upcall(). Copying the trapframe cannot always be
done with a simply bcopy() or may not always be optimal that way. On
ia64 specifically the trapframe contains information that is specific
to an entry into the kernel and can only be used by the corresponding
exit from the kernel. A trapframe copied verbatim from another frame
is in most cases useless without some additional normalization.
Note that this change removes the assignment to td->td_frame in some
implementations of cpu_set_upcall(). The assignment is redundant.
A previous call to cpu_thread_setup() already did the exact same
assignment. An added benefit of removing the redundant assignment is
that we can now change td_pcb without nasty side-effects.
This change officially marks the ability on ia64 for 1:1 threading.
Not tested on: amd64, powerpc
Compile & boot tested on: alpha, sparc64
Functionally tested on: i386, ia64
Always route PCI interrupts on i386 UP machines. I was planning to enable
this for i386 anyways once SMP support is done. Having this enabled fixes
problems on many people's laptops.
Requested by: imp
Attach to the component devices using GEOM semantics.
Create a GEOM provider instead of using disk_create()
Use the GEOM OAM api for configuration.
I saw approx ~1% speedup in througput and ~7% in latency in a
simple minded test of a two-disk striped device.
This file was repo-copied from src/sys/dev/ccd/ccd.c.
This is not yet linked into the build.
While a string is readable without a tool, an array is easier to process for
a monitoring application. This also prevents the extra hoops we need with
sbufs and locking.
Move the mtx_init() in en_attach() higher before the first failure point so
that we can unconditionally destroy it in en_destroy().
extattr_list_link() system calls, which return a least of extended
attributes defined for a vnode referenced by a file descriptor
or path name. Currently, we just invoke VOP_GETEXTATTR() since
it will convert a request for an empty name into a query for a
name list, which was the old (more hackish) API. At some point
in the near future, we'll push the distinction between get and
list down to the vnode operation layer, but this provides access
to the new API for applications in the short term.
Pointed out by: Dominic Giampaolo <dbg@apple.com>
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
file/directory/link, rather than using a less explicit hack on
the extattr retrieval API:
extattr_list_fd()
extattr_list_file()
extattr_list_link()
The existing API was counter-intuitive, and poorly documented.
The prototypes for these system calls are identical to
extattr_get_*(), but without a specific attribute name to
leave NULL.
Pointed out by: Dominic Giampaolo <dbg@apple.com>
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
Don't copyin() data we are about to overwrite.
Add a flag to tell userland that KSE is officially "DONE" with the
mailbox and has gone away.
Obtained from: davidxu@
we failed to put the bucket back into the general cache/container.
Also, fix a bad assumption. There was a KASSERT() that aimed to
guarantee that whenever the pcpu container's mc_starved was > 0,
that whatever the bucket we were freeing to was an empty bucket,
assuming it belonged to the pcpu container cache. However, there
is at least one case where this is not true anymore; consider:
1) All containers empty, next thread to try to alloc will touch
a pcpu container, notice it's empty, and increment the pcpu
container's mc_starved.
2) Some other thread frees an mbuf belonging to a bucket in
the general cache/container. Then it frees another mbuf
belonging to the same bucket (still in gen container).
3) Some third thread tries to allocate an mbuf from the pcpu
container and, since empty, grabs one mbuf now available
in the general cache and moves the non-empty bucket from
which it took 1 mbuf and to which the thread in (2) freed
to, and moves it to the pcpu container.
4) A final thread tries to free an mbuf belonging to the
NON-EMPTY bucket mentionned in (2) and (3) and, since
the pcpu container's mc_starved is > 0, but the bucket
is obviously non-empty, it trips on the KASSERT.
This meant that one could potentially get a panic in some
cases when out of mbufs and clusters. The problem could
be mitigated by commenting out some cv_signal() calls,
but I'm assuming that was pure coincidence and this is
the correct fix.
on my part. The output asm looks correct with the previous commit in place
and it works on amd64, but on my laptop I got a spew of AE_BAD_PARAMETER
errors trying to unlock the acpi global lock.
and releasing ACPI global locks instead of (ab)using the pointers to those
locks as the constants. Also, rather than require that the address of
the lock be stored in a register, use a memory constraint allowing the
memory address to be used directly.
Noticed by: peter
- Use a hash of umtx queues to queue blocked threads. We hash on pid and the
virtual address of the umtx structure. This eliminates cases where we
previously held a lock across a casuptr call.
Reviwed by: jhb (quickly)
to unload. This would cause a panic on the second resetconfig.
Start Vinum at boot time at SI_SUB_RAID, not SI_SUB_VINUM.
SI_SUB_VINUM was there first, but there's no real distinction, and
SI_SUB_RAID is a more neutral name.
Submitted by: hmp
o adding locking to op submission
o mark interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts should be sufficient
o change mutex string names so witness printouts are more meaningful
Note: locking is still pretty brute-force but it's probably not worth
improving it given the relatively low performance of hifn-based cards.
o replace driver-global lock with three locks: one for the handling of mcr1
operations, one for handling of mcr2 operations, and one for the mcr1
free list
o mark the interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts is sufficient (I think)
o add a ``done'' flag for crypto operations; this is set when the operation
completes and is intended for callers to check operations that may complete
``prematurely'' because of direct callbacks
o close a race for operations where the crypto driver returns ERESTART: we
need to hold the q lock to insure the blocked state for the driver and any
driver-private state is consistent; otherwise drivers may take an interrupt
and notify the crypto subsystem that it can unblock the driver but operations
will be left queued and never be processed
o close a race in /dev/crypto where operations can complete before the caller
can sleep waiting for the callback: use a per-session mutex and the new done
flag to handle this
o correct crypto_dispatch's handling of operations where the driver returns
ERESTART: the return value must be zero and not ERESTART, otherwise the
caller may free the crypto request despite it being queued for later handling
(this typically results in a later panic)
o change crypto mutex ``names'' so witness printouts and the like are more
meaningful
all the argument registers etc since we have almost certainly have trashed
them by now. Take particular car of %r10 since it held the original value
of %rcx (which we saved in tf_rcx on entry and doreti doesn't know this).
Change the list interface to simplify things.
Remove old list ioctls which bogusly exported the softc to userland.
Move the softc and associated structures from the public header to
the source file.
Make CCD a GEOM class.
For now only use this for implementing a OAM config method which
can return a list of configured CCD devices in the format which
"ccdconfig -g[v]" would normally output.
mpo_copy_mbuf_label() entry point for Biba and MLS, respectively.
Otherwise, labels in m_tags may not be properly propagated across
some classes of mbuf operations. This problem caused these policies
to fail-stop the system with a panic.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
Two tokens that don't together form a vaid preprocssor token cannot be
pasted together using ANSI-C token concatinatation. GCC 3.2's cpp, at least,
produces the desired result w/o using "##".
Clarify that the implicit fallthrough was *not* intentional (thanks, Poul!)
and reorganize the code so a correct fallthrough (with /* FALLTHROUGH */)
occurs.
o Use pcb and tf for the new pcb and the new trapframe and use pcb0
for the old (current) pcb. The mix of pcb, pcb2 and tf was slightly
confusing.
o Don't define td->td_frame here. It has already been set previously
by cpu_thread_setup. Add a KASSERT to make sure pcb and tf are both
non-NULL.
o Make sure the number of dirty registers is 0 for the new thread.
There are no user registers on the backing store because we heven't
enter userland yet.
is not called, and no static rules match an outgoing packet, the
latter retains its source IP address. This is in support of the
"static NAT only" mode.
bzero(ptr, sizeof(DC_RXLEN * 5));
which should obviously be:
bzero(ptr, DC_RXLEN * 5);
Looks like this bug may have reduced the effectiveness of the
workaround for the hardware bug in the PNIC chips.
MFC after: 1 week
o Remove register keyword
o ANSIfy prototypes
o Remove "return;" at the end of void functions
o Remove trailing spaces
o Don't align local variables with tabs and reorder them
o Don't use /* FOO */ at the end of a #ifdef FOO block if
it's a small block
- Other non-functional changes :
o 6 -> ETHER_ADDR_LEN
o Don't initialize if_output; ether_ifattach() does it for us
hinge on the "verb" parameter which the class gets to interpret as
it sees fit.
Move the entire request into the kernel and move changed parameters
back when done.
Sleep on the vnode interlock while waiting for another
caller to increment fi_readers or fi_writers. Hold the
vnode interlock while incrementing fi_readers or fi_writers
to prevent a wakeup from being missed.
Only access fi_readers and fi_writers while holding the vnode
lock. Previously fifo_close() decremented their values without
holding a lock.
Move resource deallocation from fifo_close() to fifo_inactive(),
which allows the VOP_CLOSE() call in the error return path in
fifo_open() to be removed. Fifo_open() was calling VOP_CLOSE()
with the vnode lock held, in violation the current vnode locking
API. Also the way fifo_close() used vrefcnt() to decide whether
to deallocate resources was bogus according to comments in the
vrefcnt() implementation.
Reviewed by: bde
the lameness of the kstack code. The EPC overhaul de-lame-ified the
kstack code by removing the need for contigmalloc(). We can now
allocate stacks using malloc(). We probably want to make the stacks
swappable as well so that we can make it MI. But that's another story.
-Werror build with such option, but not other combinations. LINT
misses this because syscons knobs in LINT turn off a lot of code.
Reviewed by: marcel (some time ago)
if we permit them to occur, the kernel panics due to our performing
EA operations using VOP_STRATEGY on the vnode. This went unnoticed
previously because there are very for users of device nodes on UFS2
due to the introduction of devfs. However, this can come up with
the Linux compat directories and its hard-coded dev nodes (which will
need to go away as we move away from hard-coded device numbers).
This can come up if you use EA-intensive features such as ACLs and
MAC.
The proper fix is pretty complicated, but this band-aid would be
an excellent MFC candidate for the release.
why certain exceptions are made, note an inconsistency between
FreeBSD and some other implementations regarding IPC_M, and let
suser() generate our EPERM rather than forcing it ourselves.
Remove a carriage return that crept in in the last commit.
Reviewed by: gordon
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
gateway page is considered kernel space, we can panic when we should
only SIGSEGV. Hence, add the additional constraint that for page
faults we also require running with kernel privileges. The gateway
page is the only kernel code running with user privileges, iso this
is a correct way to exclude the gateway page from kernel land.
We do not currently exclude the gateway page for other faults as it
is not always the right way to do it. Further tuning will happen on
a case by case bases.
thr_create(2). This implementation is so far only compile tested.
But since this is also the last of the functions required to
support libthr, we're now functionally complete (for some weird
definition of functionally; and complete). Runtime testing can
commence.
sigreturn(), we cheat and assume the preserved registers are still
on-chip and unmodified. This is actually the case, but more by accident
than by design. We need to use unwinding eventually or explicitly
compile the kernel in a way that the compiler steers clear from using
the preserved registers completely.
o The SDM states that flushing the RSE in the cycle prior to the
call to ia32 code yields the best performance. We don't really
care to much about performance here, but we do the same anyway.
I'm being paranoia and conservative here.
o Only initialize the ia32 state registers, not the registers used
as scratch by the ia32 engine. This saves a couple of loads from
the trapframe, but also helps debugging: we don't clobber useful
debugging data (engineering hints :-)
o Make sure all general registers constituting ia32 state have been
initialized. If there's no useful to be loaded from the trapframe,
clear the register. This avoids accidentally leaking NaT bits.
o Make sure we set ar.k6 prior to clobbering ar.bspstore and also
set ar.k7 prior to setting sp. This fixes a race seen for ia64
native code as well (and previously fixed too).
backing store before we discard them. It is possible that we
enter the kernel (due to an execve in this case) with a lot of
dirty user registers and that the RSE has only partially spilled
them (to make room for new frames). We cannot move the backing
store pointer down (to discard user registers) when not all of
the user registers are on the backing store.
So, we flush the register stack IFF this happens. Unconditionally
doing the flush is too costly, because the condition in which we
need to flush is very rare.
This change appears to fix the SIGSEGV that sometimes happen for
newly executed processes and so far also appears to fix the last
of the corruption. It is possible, although not likely, that this
change prevents some other bug from happening, even though it is
itself not a fix. Hence the uncertainty. We'll know in a couple
of months I guess :-)
the stack to be changed in a way incompatible with elf32_map_insert()
where we used data_buf without initializing it for when the partial
mapping resulting in a misaligned image (typical when the page size
implied by the image is not the same as the page size in use by the
kernel). Since data_buf is passed by reference to vm_map_find(), the
compiler cannot warn about it.
While here, move all local variables to the top of the function.
of C strings internally; C strings require a lot of return value
checking that (a) takes a lot of space, and (b) is difficult to get
right. Prior to the advent of compartment support, modeling APIs
for helper functions on snprintf worked fine; with the additional
complexity, the sbuf_printf() API makes a lot more sense.
While doing this, break out the printing of sequential compartment
lists into a helper function, mac_{biba,mls}_compartment_to_string().
This permits the main body of mac_{biba,mls}_element_to_string()
to be concerned only with identifying sequential ranges rather
than rendering.
At a less disruptive moment, we'll push the move from snprintf()-like
interface to sbuf()-like interface up into the MAC Framework layer.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
Use ->init() and ->fini() to handle the mutex in geom_disk.c
Remove the g_add_class() function and replace it with a standardized
g_modevent() function.
This adds the basic infrastructure for loading/unloading GEOM classes
only meaningful for fragments. Also don't bother to byte-swap the
ip_id when we do generate it; it is only used at the receiver as a
nonce. I tried several different permutations of this code with no
measurable difference to each other or to the unmodified version, so
I've settled on the one for which gcc seems to generate the best code.
(If anyone cares to microoptimize this differently for an architecture
where it actually matters, feel free.)
Suggested by: Steve Bellovin's paper in IMW'02
switch to it before calling mi_startup(). The bootstack is WAY too small
for running acpica during probe/attach. While here, pass modulep/physfree
to the startup routine, rather than writing to the global variables in
locore.S.
Approved by: re (amd64/*)
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.
To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).
Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.
Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)
The current name is confusing, because it indicates to
the client that a bus_dmamap_sync() operation is not
necessary when the flag is specified, which is wrong.
The main purpose of this flag is to hint the underlying
architecture that DMA memory should be mapped in a coherent
way, but the architecture can ignore it. But if the
architecture does supports coherent mapping of memory, then
it makes bus_dmamap_sync() calls cheap.
This flag is the same as the one in NetBSD's Bus DMA.
Reviewed by: gibbs, scottl, des (implicitly)
Approved by: re@ (jhb)
nfs_lock.c. Right now, if we permit a signal to interrupt the sleep,
we will slip the lock and no process on that client, the server, or
any other client will be able to acquire the lock. This can happen,
for example, if a user hits Ctrl-C or Ctrl-T while a process is
waiting for the lock. By removing PCATCH, we prevent that from
happening, at the cost of not permitting a user-requested lock abort:
also nasty. However, a user interface bug might be preferable to a
serious semantic bug, so we go with that for now.
We need to teach the rpc.lockd/kernel protocol how to abort lock
requests, and rpc.lockd how to handle aborted lock requests; patches
for the kernel bit are floating around, but no rpc.lockd bit yet.
Approved by: re (scottl)
mismerged from the MAC tree, and didn't get picked up because warnings
are not normally fatal in per-module builds, only when they are linked
into a kernel (such as LINT).
Reported by: des and the technicolor tinderbox
Approved by: re (scottl)
Use the special LUNLEN_SINGLE_LEVEL constant for
post Rev A4 hardware for single byte luns. Without
this change, Rev B hardware would place the single
byte of lun data in byte 0 of the lun structure when
it should be in byte 1. Since there are few if any
devices on the market that support multiple luns in
target mode, the corrupted lun field (which was only
corrupted for non-zero luns) wasn't hurting us.
Approved by: re (rwatson)
aic79xx.h:
aic79xx.reg:
Return the SCB_TAG field to 16byte alignment.
It seems that on some PCI systems, SCBs are not
transferred correctly to the controller with
the previous placement of the SCB_TAG field.
Approved by: re (rwatson)
section to stop gcc generating the dwarf2 .eh_frame unwind tables. It
is dead weight for the time being. Maybe it can be used to perform
stack traces and/or get the location of function arguments in ddb, but
that requires a dwarf2 runtime interpreter, which we do not have.
Approved by: re (amd64 "safe" bits)
disassembler has not been updated yet, and will do some very strange
things. It does tracebacks (without function arguments due to regparm
calling conventions) if -fno-omit-frame-pointer is used (to come later).
This achieves basic functionality.
Approved by: re (amd64/* blanket)
