interface didn't be attached automatically at boot time so changes a
approach to attach children based on leveraging some newbus niceties.
Submitted by: nwhitehorn
- change the way in which command queue overflow is handled;
- do not expose to CAM two command slots, used for driver's internal purposes;
- allow driver to use up to 1024 command slots, instead of 256 before.
88E1149 PHY. This will fix intermittent watchdog timeouts as well
as very slow network performance on 88E8072 Yukon Extreme.
PR: kern/144148
MFC after: 1 week
o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check
does not generate excessive interrupts any more so we don't need
to have two copies of interrupt handler.
While I'm here remove two STAT_PUT_IDX register accesses in LE
status event handler. After r204539 msk(4) always sync status LEs
so there is no need to resort to reading STAT_PUT_IDX register to
know the end of status LE processing. Just trust status LE's
ownership bit.
countdown timer register. The timer resolution may vary among
controllers but the value would be represented by core clock
cycles. msk(4) will automatically computes number of required clock
cycles from given micro-seconds unit.
The default interrupt holdoff timer value is 100us which will
ensure less than 10k interrupts under load. The timer value can be
changed with dev.mskc.0.int_holdoff sysctl node.
Note, the interrupt moderation is shared resource on dual-port
controllers so you can't use separate interrupt moderation value
for each port. This means we can't stop interrupt moderation in
driver stop routine. Also have msk_tick() reclaim transmitted Tx
buffers as safety belt. With this change there is no need to check
missing Tx completion interrupt in watchdog handler, so remove it.
full-duplex. Previously msk(4) used to allow flow-control on
1000baseT half-duplex media. Also GMAC pause is enabled if link
partner is capable of handling it.
While I'm here use IFM_OPTIONS instead of using IFM_GMASK to check
optional flags of link.
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.
Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.
Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.
While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.
PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week
the issue. I still have no idea why TSO does not work on this
controller. davidch@ also confirmed there is no known TSO related
issues for this controller.
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
Reviewed by: davidch
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
for controllers like 88E8053 which reports two MSI messages.
Because we don't get anything useful things with 2 MSI messages,
allocating 1 MSI message would be more sane approach.
While I'm here, enable MSI for dual-port controllers too. Because
status block is shared for dual-port controllers, I don't think
msk(4) will encounter problem for using MSI on dual-port
controllers.
The register offset is not valid on 88E8072 controller. Also don't
blindly increase max read request size to 4096, instead, use 2048
which seems to be more sane value and only change the value if the
hardware default size(512) was used on that register.
For PCIX controllers, use system defined constant rather than using
magic value.
While I'm here stop showing negotiated link width.
not require checksum LE configuration if checksum start and write
position is the same as before. So keep track last checksum start
and write position and insert new LE whenever the position is
changed. This reduces number of LEs used in TX path as well as
slightly enhance TX performance.
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.
This fixes a panic when running tcpdump on a cxgb interface.
- Add a separate palette data for 8-bit DAC mode when SC_PIXEL_MODE is set
and fill it up with default gray-scale palette data for text. Now we don't
have to set `hint.sc.0.vesa_mode' to get the default palette data.
- Add a new adapter flag, V_ADP_DAC8 to track whether the controller is
using 8-bit palette format and load correct palette when switching modes.
- Set 8-bit DAC mode only for non-VGA compatible graphics mode.
