than just deleting them. Also add comments about why we do this.
Given the current behavior of delete_child, I don't think this changes
anything. It just feels cleaner.
try very hard to be perfect. However, these attempts broke down when
there were large numbers of resources. We'd not be able to map them all.
Instead, accept that we might pass more range to thse subbus than
might be optimal be able to compute. However, there's little harm in
this and it allows us to pass greater resources through.
# it has been suggested that we allocate a fixed amount of resources
# on attach and give it out upon request. This might not be a bad idea...
the ExCA spec, and close cousins:
o Write an activate routine that works.
o merge a couple of items from oldcard before they are lost
o write a deactivate routine
I suspect we're still a ways away from having this work, but maybe for
6.1/5.5?
o Rather than just try to turn off EXCA_INTR_RESET, set the entire register
to 0. This is slightly faster, and a better hammer.
o Move attempted clearing of the output enable (EXCA_PWRCTL_OE) back to
after we turn off the power. Modify it to write 0 so that we don't get
Bad Vcc messages on TI bridges (untested, but ru@ sent me a similar patch)
while at the same time avoiding interrupt storms on Ricoh bridges (tested
by me on my Sony).
# Many of my observations of 'breakage' for this patch are due to some bug
# in the load/unload of cbb.ko unlreated to this change. I'll be investigating
# and fixing that bug in the fullness of time.
16-bit cards when we're powering them up. Other bridges may have
similar issues, so we do this for all of them by setting the
interrupt in the PCIC register 3 to be 0 (done always anyway)
and turning on the bit in the bridge control register to route these
interrupts via the ISA bus (or via the interrupt configured in the
PCIC register 3). '0' means disable completely. There's a small
chance this may interfere with the o2micro power hacks, but I'll
wait for reports to come in from o2micro users.
o Expand some of the comments about why we do certain things.
# this gets rid of the interrupt storm warnings on my 505TS. I think
# that we may need to do something similar on suspend, but I'm unsure
# since I don't have a laptop that supports suspened/resume with a
# ricoh chipset in it.
card. Mask it while we're doing power things, as the PC Card standard
suggests. Also, poll the POWER_CYCLE bit 10x a second as well as
providing a timeout for power cycle interrupt to happen.
The Ricoh '475 that I have doesn't seem to generate an interrupt for
power at the present time, so the polling is necessary for reasons as
yet unknown. This results in an interrupt storm warning that I'm
still trying to quantify (the o2micro trick doesn't work to mitigate
this storm). At the very least, this should help those users that
lost pccards on boot with the prior rev of this code. My VAIO
PCG-505TS is now happier, but more investigation is necessary.
o Don't busy wait on powerup. Instead, use the power up interrupt to wait
for the card to power up. Don't wait when we're turning the card off,
since no interrupt happens in that case.
o Convert many of the long DELAYs to tsleeps. We do not run before
the timer have stared, so DELAY isn't necessary. More DELAYs can likely
be eliminated in the future.
o When powering up the card, don't do anything if the card is already
powered up (before we'd power cycle it). This means that for most
cards we power them up once and then never change the power.
o On card eject, mask (by clearing) the CD bit. Before we set it, which
was wrong. We don't want to see any CD events past the first one since
they need to be debounced.
With these changes, I can insert/eject 16bit cards without glitching xmms'
sound output. Something very important to the development of better pccard
drivers :-)
pcib_route_interrupt interface. Since there's only one interrupt pin
in the CardBus form factor, everybody gets to share it. Implement
cbb_route_interrupt to return the interrupt we have.
Suggested by: bms
the data sheets leads me to believe these will just work. Those parts
with the various media readers on them may not have the required
FreeBSD drivers that will attach to the subdevices that will be seen
on some of these parts.
PCI 1515, 1530, 1620, 4520, 6411, 6420, 7410, 7510, 7610
Prompted by: Havard Eidnes
These are from the datasheets downloaded from TI's web site.
They describe the PCI[67]x[12]1 and PCI[67]x20 parts, with and without
the smartcard enabled.
to try to allocate things on my parent can be taken out. It duplicates code.
Also, add comment about why the power state stuff is here (type 2
devices don't participate in the power state save/restore due to
larger Bx issues).
secondary bus is 0, we program the primary bus, the secondary bus and
the suborindate bus. This isn't ideal, since we start at parent_bus +
1 and store this in a static.
Ideally, we'd walk the tree and assign bus numbers. However, that's
harder to accomplish without some help from the bus layer which we're
not planning on doing that until 6.
This fixes my CardBus problems on my Sony PCG-Z1WA, and might fix the
Dells that have had problems.
Alignment for pccards should also be treated in a similar way that
we tread it for cardbus cards.
Remove bogus debugs while I'm here.
# This is also necessary to make the CIS reading work.
Submitted by: Carlos Velasco
