- Properly keep track of resources (I/O ports and irq).
- Use bus_space_read/write() to access the ports.
- Add PnP IDs.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
from DWLPX to PCI space. Just a methods holder such that we have a parent
which is a "pcib" and we create a child which is a "pci". Add the appropriate
ivar code (which is for a hose #).
based upon presence/absence of ISA (there is no ISA bus on an 8200- okay,
well, there *could* be one in a DWLPX tray, but we don't support it)).
Most importantly change the interrupt resource map to cover a whole 16
bits. The 8200 uses 16 bit interrupt vectors which we construct that
contain the I/O-board, hose, an pci slot in them, and then we write these
vectors into the appropriate DWLPX registers. At any rate, a flat array
of 64 'IRQs' isn't enough.
to begin with. Redo newbus attachment code so that all the DMA mapping
and further pci attachment is done right. Insert config space functions
(jeez- how do you do type 1 cycles?). Do the interrupt setups, etc.
Basically, this is the core I/O module for 8200s, even though logically
it's the 3rd level down from the nominal principle backplane bus
(turbolaser). Still to be done here: S/G code isn't done yet, so we
better live with 2GB or less primary memory.
code (merge in progress made in NetBSD since the initial import to
FreeBSD). Create dwlpx as the child device. Of course, if we had
more h/w and time, we could find out whether the child device was
a FutureBus module, etc...Anyone ever actually seen one?
clean MI/MD driver, but it *does* actually work at this time. Updated
to use new make_dev stuff. A CONS_DRIVER declaration is also put in
so that this can be the real console for the 8200s.
not the current BPF device should report locally generated packets or not.
This allows sniffing applications to see only packets that are not generated
locally, which can be useful for debugging bridging problems, or other
situations where MAC addresses are not sufficient to identify locally
sourced packets. Default to true for this flag, so as to provide existing
behavior by default.
Introduce two new ioctls, BIOCGSEESENT and BIOCSSEESENT, which may be used
to manipulate this flag from userland, given appropriate privilege.
Modify bpf.4 to document these two new ioctl arguments.
Reviewed by: asmodai
this version include:
- Support for version 2.x firmware (2.42 or later recommended). This
means we are the only open-source driver supporting these adapters.
This code has only been tested on a Digital KZPCA adapter in an Alpha
system, but is believed to be correct. NOTE: EISA adapters are not
yet supported.
- Support the BIOS/Firmware initialisation handshake protocol. This
allows the driver to bring the card up to operational state even if
the BIOS can't be run (eg. if it's an x86 BIOS in an Alpha system).
- A working command pasthrough interface. This allows a user-space
configuration tool (under development) to issue arbitrary commands
to the controller or to devices in the system.
return ENXIO (Device not configured). Without this, vn_isdisk()
could (and did in the case of lstat() under fdesc) pass a NULL pointer
to devsw(), which caused a page fault.
Reviewed by: alfred
``Depending on the setting of the sysctl variable `net.inet.ipfw.one_pass'
Packets coming from a pipe ...''
into
``... the sysctl variable `net.ipfw.one_pass', packets coming from ...''
while the other half used `vap', and in one case resulted in code that
made no sense. Replaced all of them with `vap'.
(Typically, `vpp' is a pointer to a pointer to a struct vnode anyway).
