cloning infrastructure standard in kern_conf. Modules are now
the same with or without devfs support.
If you need to detect if devfs is present, in modules or elsewhere,
check the integer variable "devfs_present".
This happily removes an ugly hack from kern/vfs_conf.c.
This forces a rename of the eventhandler and the standard clone
helper function.
Include <sys/eventhandler.h> in <sys/conf.h>: it's a helper #include
like <sys/queue.h>
Remove all #includes of opt_devfs.h they no longer matter.
change channel interface - kobj implementation coming soonish
make pcm_makelinks not panic if modular
add pcm_unregister()
these changes support newpcm kld unloading, but this is only implemented
by ds1.c
modify driver capability reporting format to list every audio format
seperately- required for above and because we could not previously indicate
that mono was unsupported.
there should be no functional impact.
in bogus hwptr warnings. Further comments sought on -hackers
were not forthcoming. I can only hope that calling DELAY() like
this doesn't cause any heartburn.
position, channel 1's dma position register must be quiescent. So
the driver will spl, pause the DMA, delay a bit and hold as still as
possible while snapping the picture.
I'm sure there HAS to be a better way to do this, but if there is, it's
not documented.
So far as I can tell, this fixes recording, which means the Solo is open
for business.
2. Offer half duplex with both playback and record on channel 1 or
full duplex with playback always on channel 2 as a compile-time option.
3. 16 bit record output is byte swapped for some dumb reason. Report the _BE
AFMTs for recording.
16 bit samples have some sort of choppiness, the nature of which
is not completely clear, but it clearly has something to do with
dma buffer synchronization. But at least channel 1 makes noise now.
appears to be the correct length, but quality of output has not yet
been tested. Also, full duplex audio (that is, playback on channel 1)
does not yet work. Two constants and I am there!
Obtained from: major hints from ALSA
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
motherboards that use YMF740's. It has a strange subvendor and subdevice
ID and requires a disturbingly long delay after the ac97 codec init.
Cameron hasn't had this driver tested on another 740 yet, so we don't know
if this is a quirk of all 740's, or if its just something about the codec
that Intel used.
conf/files
i don't seem to be clearing the cache right resulting in a short initial
burst of noise, despite doing the same as creative and alsa. i'm committing
now so more eyes can pore over the code.
* add a callback for initialising the mixer interface
* support ac97 2.1 variable rate audio feature
fix ac97-using drivers for the above
add suspend/resume support for neomagic
whilst we are playing or recording. since we should irq ~20 times/sec when
active, this should never trigger. in theory. if it never does trigger,
the check will be removed.
then invoke the children. As the value of HISR can be read
only once, pass the HISR to the children via struct
csa_bridgeinfo, stored in the ivars of them.
- Clear the contents of serial FIFO upon stopping the DMA for
playing. This may eliminate buzz on playing. Experimental.
Also, optimize out a mess of #if's that were duplicating work already
done by config(8). For example, if a file is marked as
"dev/sound/pci/foo.c optional pcm pci" then it's only added if pcm *and*
pci are present, so #if NPCM > 0 and #if NPCI > 0 are totally redundant.
A bit more work is still needed.
Discussed with: cg (a few weeks ago)
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
ES1371 and ES1373 PCI Audio Sound Chips.
The 1371 and 1373 can be found on newer CreativeLabs/Ensoniq
sound cards such as the SoundBlaster PCI 16,64 and 128.
Submitted by: Russell Cattelan <cattelan@thebarn.com>
Obtained from: Parts obtained from linux, but rewritten by Russell
