we create the pty on the fly when it is first opened.
If you run out of ptys now, just MAKEDEV some more.
This also demonstrate the use of dev_t->si_tty_tty and dev_t->si_drv1
in a device driver.
kernels again, now that we're using EGCS/GCC 2.9+. This "here"
file is compatible with the Bourne shell and the Korn shell (incl. pdksh
and KSH93 from AT&T, which I do have), so it doesn't make newvers.sh
unportable, but makes it easier to modify in the future/read now.
Submitted by: green
Specifically intended for removing -fschg ("INSTALLFLAGS_EDIT=:S/schg/uchg/")
this makes the NOFSCHG flag redundant. NOFSCHG will still be honoured by
bsd.lib.mk but is valid for buildworld only. NOFSCHG is still implemented in
the old way (ie. _not_ ".if NOFSCHG then { INSTALLFLAGS_EDIT+=:S/schg/,/ }"
to emphasize the fact that NOFSCHG is only supported in a limited
fashion and for buildworld.
The interface and implementation are such that future use of flags such
as sappnd can also be easily removed or altered (perhaps to uappnd).
This commit brought to you by the letters B, D, and E, and the numbers six,
one, thirteen, and three.
- Add support for calling 32-bit code in other segments
- Add support for calling 16-bit protected mode code
Update APM to use this facility.
Submitted by: jlemon
macros) to the signal handler, for old-style BSD signal handlers as
the second (int) argument, for SA_SIGINFO signal handlers as
siginfo_t->si_code. This is source-compatible with Solaris, except
that we have no <siginfo.h> (which isn't even mentioned in POSIX
1003.1b).
An rather complete example program is at
http://www3.cons.org/cracauer/freebsd-signal.c
This will be added to the regression tests in src/.
This commit also adds code to disable the (hardware) FPU from
userconfig, so that you can use a software FP emulator on a machine
that has hardware floating point. See LINT.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
into uipc_mbuf.c. This reduces three sets of identical tunable code to
one set, and puts the initialisation with the mbuf code proper.
Make NMBUFs tunable as well.
Move the nmbclusters sysctl here as well.
Move the initialisation of maxsockets from param.c to uipc_socket2.c,
next to its corresponding sysctl.
Use the new tunable macros for the kern.vm.kmem.size tunable (this should have
been in a separate commit, whoops).
On the VAX, it used to be used for special compilation to avoid the
optimizer which would mess with memory mapped devices etc. These days
we use 'volatile'.
SYSINIT_KT() etc (which is a static, compile-time procedure), use a
NetBSD-style kthread_create() interface. kproc_start is still available
as a SYSINIT() hook. This allowed simplification of chunks of the
sysinit code in the process. This kthread_create() is our old kproc_start
internals, with the SYSINIT_KT fork hooks grafted in and tweaked to work
the same as the NetBSD one.
One thing I'd like to do shortly is get rid of nfsiod as a user initiated
process. It makes sense for the nfs client code to create them on the
fly as needed up to a user settable limit. This means that nfsiod
doesn't need to be in /sbin and is always "available". This is a fair bit
easier to do outside of the SYSINIT_KT() framework.
