Including arm/mv/gpio.c now depends on 'gpio' device. 'device gpio' was
added to all kernconf files of Marvell boards, except ARMADAXP (dummy
mv_gpio_res definition was removed) and ARMADA38X (not supported yet).
This commit allows to use generic files.mv on A38X.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4372
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
BREAK_TO_DEBUGGER if they have a serial console (most do). A burst of
serial line noise (such as unplugging a usb serial adapter) can look like
a break and drop a working system into the debugger. The alt break sequence
(<CR>~^B) works fine on both serial and non-serial consoles.
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
which means that the NFSCLIENT and NFSSERVER
kernel options will no longer work. This commit
only removes the kernel components. Removal of
unused code in the user utilities will be done
later. This commit does not include an addition
to UPDATING, but that will be committed in a
few minutes.
Discussed on: freebsd-fs
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
This adds support for version 10, revision 01, but it should also work
without changes for the 0901 model, at least until we get drivers for the
two different wifi chips involved.
Many users contributed to and tested the various patchsets floating around
for the past year that have eventually evolved into this checkin, most notably
Richard Neese who provided the bulk of the kernel config file.
Approved by: cognet (mentor)
