controllers combine multiple TX requests into single one if there
is room in TX buffer of controller. Updating TX packet counter at
the end of TX completion resulted in incorrect TX packet counter as
axe(4) thought it sent 1 packet. There is no easy way to know how
many combined TX were completed in the callback.
Because this change updates TX packet counter before actual
transmission, it may not be ideal one. But I believe it's better
than showing fake 8kpps under high TX load. With this change, TX
shows 221kpps on Linksus USB200M.
scratch. This driver adds support for USB3.0 devices. The XHCI
interface is also backwards compatible to USB2.0 and USB1.0 and will
evntually replace the OHCI/UHCI and EHCI drivers.
There will be follow-up commits during the coming week to link the
driver into the default kernel build and add missing USB3.0
functionality in the USB core. Currently only the driver files are
committed.
Approved by: thompsa (mentor)
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
vendor ID in the vendor section, and by symbolic name in the product
section. Products are sorted by product ID. While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.
MFC after: 1 week
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
plug. Note that the Vendor ID 0x04b4 is officially assigned to Cypress,
so use that instead of adding a second vendor with an identical ID, in the
same way other similar cases are treated in usb/usbdevs.
PR: usb/132785
Submitted by: Dirk-Willem van Gulik <dirkx webweaving.org>
MFC after: 1 week
- Fixed the interface probe routine to only attach to USB interfaces the driver
actually supports. This allows other drivers to attach to things like
MicroSD slots etc.
- Fixed network interface enumeration to be globally sequential instead of
relying on the USB interface numbers. This make sure the first network
interface always is at uhso0 and the second at usho1 and so on.
- Added a radio kill switch; exposed through sysctl.
- Updated the manual page to be verbose about the number of serial ports and
include iCON 452 in the set of tested hardware.
Submitted by: Fredrik Lindberg
callback function will be executed, and that the key won't be deleted during
the init process.
- txmic and rxmic are written into the chip the same place regardless of
opmode.
- Make the hardware generate 802.11 sequence numbers.
Submitted by: Akinori Furukoshi
Obtained from: git://gitorious.org/run/run.git
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
