perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
Sense ${DEBUG} to decide on building kernel.debug or not.
Use a common install and install.debug target to minimize duplication.
(I deleted the ELF transition kernel warning, it was getting dated..)
Requested-by: ache
bde
dg
Modify targets for debug kernels: when -g was specified, make will
now build a debug kernel called kernel.debug, and create a stripped
version called kernel at the same time. The two targets install and
install.debug are otherwise unchanged.
Requested-by: dillon
Update man page accordingly.
2. Config complains if you use -g:
Debugging is enabled by default, there is no ned to specify the -g option
3. Config warns you if you don't use -s:
Building kernel with full debugging symbols. Do
"config -s BSD" for historic partial symbolic support.
To install the debugging kernel, do make install.debug
(BSD was the name of the config file I used; I print out the same
name).
4. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 and config to
work if a kernel name other than 'kernel' is specified. This is
not absolutely necessary, but useful, and it was relatively easy.
I now have a kernel called /crapshit :-)
5. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 "clean" target
to remove both the debug and normal kernel.
6. Modify all to install the stripped kernel by default and the debug
kernel if you enter "make install.debug".
7. Update version number of Makefiles and config.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
bootblocks in order to boot the kernel after this! Also note that this
change breaks BSDI BSD/OS compatibility.
Also increased default NKPT to 17 so that FreeBSD can boot on machines
with >=2GB of RAM. Booting on machines with exactly 4GB requires other
patches, not included.
KBD_INSTALL_CDEV).
- Removed the note that the VESA option cannot be used on the SMP system;
this is not true.
- Moved the option VESA to more appropriate place.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
their ttl). This can be used - in combination with the proper ipfw
incantations - to make a firewall or router invisible to traceroute
and other exploration tools.
This behaviour is controlled by a sysctl variable (net.inet.ip.stealth)
and hidden behind a kernel option (IPSTEALTH).
Reviewed by: eivind, bde
This is for various Olicom cards. An IBM driver is following.
This patch also adds support to tcpdump to decode packets on tokenring.
Congratulations to the proud father.. (below)
Submitted by: Larry Lile <lile@stdio.com>
