Commit Graph

10 Commits

Author SHA1 Message Date
Pyun YongHyeon
d612cc5947 IEEE 802.3 Annex 28B.3 explicitly specifies the following relative
priorities of the technologies supported by 802.3 Selector Field
value.

1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T

However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.

PR:	92599
2007-11-16 10:25:36 +00:00
Pyun YongHyeon
41cfbdeb51 If the PHY has 1000BASE-T capability, check to see if a 1000BASE-T speed
was negotiated.

Obtained from:  NetBSD
2006-05-19 03:51:42 +00:00
Marius Strobl
50aa106108 Remove double __FBSDID and move the remaining one into a common place after
the license(s) and before the driver comment (the latter only in drivers not
having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
David E. O'Brien
aad970f1fe Use __FBSDID().
Also some minor style cleanups.
2003-08-24 17:55:58 +00:00
David E. O'Brien
8368cf8f75 Use __FBSDID rather than rcsid[]. 2003-04-03 21:36:33 +00:00
Poul-Henning Kamp
e5fbad8bca Convert exphy and ukphy over to the new code.
exphy is done flying blind, ukphy is tested on one card.
2002-04-29 13:35:31 +00:00
Poul-Henning Kamp
eb95c536ad Remove unneeded #include <sys/kernel.h> 2000-04-29 15:36:14 +00:00
Poul-Henning Kamp
3389ae9350 Remove ~25 unneeded #include <sys/conf.h>
Remove ~60 unneeded #include <sys/malloc.h>
2000-04-19 14:58:28 +00:00
Peter Wemm
c3aac50f28 $Id$ -> $FreeBSD$ 1999-08-28 01:08:13 +00:00
Bill Paul
d00275330d This commit adds support for the NetBSD MII abstraction layer and
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.

This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.

There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.

Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.

I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
1999-08-21 17:40:53 +00:00