It is common for freelists to be starving when a netmap application
stops. Mailbox commands to free queues can hang in such a situation.
Avoid that by not freeing the queues when netmap is switched off.
Instead, use an alternate method to stop the queues without releasing
the context ids. If netmap is enabled again later then the same queue
is reinitialized for use. Move alloc_nm_rxq and txq to t4_netmap.c
while here.
MFC after: 1 week
Sponsored by: Chelsio Communications
r367917 fixed the backpressure on the netmap rxq being stopped but that
doesn't help if some other netmap rxq is starved (because it is stopping
too although the driver doesn't know this yet) and blocks the pipeline.
An alternate fix that works in all cases will be checked in instead.
Sponsored by: Chelsio Communications
The netmap application using the driver is responsible for replenishing
the receive freelists and they may be totally depleted when the
application exits. Packets in flight, if any, might block the pipeline
in case there aren't enough buffers left in the freelist. Avoid this by
filling up the freelists with a driver allocated buffer.
MFC after: 1 week
Sponsored by: Chelsio Communications
The firmware can allocate ingress and egress context ids anywhere from
its configured range. Size the iq/eq maps to match the entire range
instead of assuming that the firmware always allocates the first
available context id.
Reported by: Baptiste Wicht @ Verisign
MFC after: 1 week
Sponsored by: Chelsio Communications
Bind the netmap tx queues to a special '0xff' scheduling class which
makes the firmware skip some processing related to rate limiting on the
outgoing traffic. Future firmwares will do this automatically.
MFC after: 1 week
Sponsored by: Chelsio Communications
- Only active netmap receive queues should be in the RSS lookup table.
- The RSS table should be restored for NIC operation when the last
active netmap queue is switched off, not the first one.
- Support repeated netmap ON/OFF on a subset of the queues. This works
whether the the queues being enabled and disabled are the only ones
active or not. Some kring indexes have to be reset in the driver for
the second case.
MFC after: 1 week
Sponsored by: Chelsio Communications
There were quite a few places where port_info was being accessed only to
get to the adapter.
Reviewed by: jhb@
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D25432
This reduces the lines bouncing around between the driver rx ithread and
the netmap rxsync thread. There is no net change in the size of the
struct (it continues to waste a lot of space).
This kind of split was originally proposed in D17869 by Marc De La
Gueronniere @ Verisign, Inc.
MFC after: 1 week
Sponsored by: Chelsio Communications
The cong_drop setting will apply to queues created after the setting is
changed and not to existing queues.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
This simplifies the driver's rx fast path as well as the bookkeeping
code that tracks various rx buffer sizes and layouts.
MFC after: 1 week
Sponsored by: Chelsio Communications
TX_PKTS2 is more efficient within the firmware and this improves netmap
Tx by a few Mpps in some common scenarios.
MFC after: 1 week
Sponsored by: Chelsio Communications
After the fix contained in r341144, cxgbe does not need anymore
to set the IFCAP_NETMAP flag manually.
Reviewed by: np
Approved by: gnn (mentor)
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17987
A kernel panic can occur if the cxgbe interface is DOWN
when activating netmap. This patch prevents the driver
from freeing up cxgbe netmap resources when they have not
been allocated.
Submitted by: Nicolas Witkowski <nwitkowski@verisign.com>
Reviewed by: np
MFC after: 1 week
Sponsored by: Verisign, Inc.
Differential Revision: https://reviews.freebsd.org/D17802
interface into two groups. Filters can be used to match traffic
and distribute it across a group.
hw.cxgbe.nm_split_rss
Sponsored by: Chelsio Communications
of descriptors processed. Add the ability to gather a certain maximum
number of frames in the driver's rx before waking up netmap rx. If
there aren't enough frames then netmap rx will be woken up as usual.
hw.cxgbe.nm_rx_nframes
Sponsored by: Chelsio Communications
Changelist:
- Turn tx_rings and rx_rings arrays into arrays of pointers to kring
structs. This patch includes fixes for ixv, ixl, ix, re, cxgbe, iflib,
vtnet and ptnet drivers to cope with the change.
- Generalize the nm_config() callback to accept a struct containing many
parameters.
- Introduce NKR_FAKERING to support buffers sharing (used for netmap
pipes)
- Improved API for external VALE modules.
- Various bug fixes and improvements to the netmap memory allocator,
including support for externally (userspace) allocated memory.
- Refactoring of netmap pipes: now linked rings share the same netmap
buffers, with a separate set of kring pointers (rhead, rcur, rtail).
Buffer swapping does not need to happen anymore.
- Large refactoring of the control API towards an extensible solution;
the goal is to allow the addition of more commands and extension of
existing ones (with new options) without the need of hacks or the
risk of running out of configuration space.
A new NIOCCTRL ioctl has been added to handle all the requests of the
new control API, which cover all the functionalities so far supported.
The netmap API bumps from 11 to 12 with this patch. Full backward
compatibility is provided for the old control command (NIOCREGIF), by
means of a new netmap_legacy module. Many parts of the old netmap.h
header has now been moved to netmap_legacy.h (included by netmap.h).
Approved by: hrs (mentor)
leaves the firmware event queue (fwq) as the only queue that can take
interrupts for others.
This simplifies cfg_itype_and_nqueues and queue allocation in the driver
at the cost of a little (never?) used configuration. It also allows
service_iq to be split into two specialized variants in the future.
MFC after: 2 months
Sponsored by: Chelsio Communications
Do not attempt to initialize netmap queues that are already initialized
or aren't supposed to be initialized. Similarly, do not free queues
that are not initialized or aren't supposed to be freed.
PR: 217156
Sponsored by: Chelsio Communications
VF devices use a different register layout than PF devices. Storing
the offset in a value in the softc allows code to be shared between the
PF and VF drivers.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7389
vcxgbe/vcxl interfaces and retire the 'n' interfaces. The main
cxgbe/cxl interfaces and tunables related to them are not affected by
any of this and will continue to operate as usual.
The driver used to create an additional 'n' interface for every
cxgbe/cxl interface if "device netmap" was in the kernel. The 'n'
interface shared the wire with the main interface but was otherwise
autonomous (with its own MAC address, etc.). It did not have normal
tx/rx but had a specialized netmap-only data path. r291665 added
another set of virtual interfaces (the 'v' interfaces) to the driver.
These had normal tx/rx but no netmap support.
This revision consolidates the features of both the interfaces into the
'v' interface which now has a normal data path, TOE support, and native
netmap support. The 'v' interfaces need to be created explicitly with
the hw.cxgbe.num_vis tunable. This means "device netmap" will not
result in the automatic creation of any virtual interfaces.
The following tunables can be used to override the default number of
queues allocated for each 'v' interface. nofld* = 0 will disable TOE on
the virtual interface and nnm* = 0 to will disable native netmap
support.
# number of normal NIC queues
hw.cxgbe.ntxq_vi
hw.cxgbe.nrxq_vi
# number of TOE queues
hw.cxgbe.nofldtxq_vi
hw.cxgbe.nofldrxq_vi
# number of netmap queues
hw.cxgbe.nnmtxq_vi
hw.cxgbe.nnmrxq_vi
hw.cxgbe.nnm{t,r}xq{10,1}g tunables have been removed.
--- tl;dr version ---
The workflow for netmap on cxgbe starting with FreeBSD 11 is:
1) "device netmap" in the kernel config.
2) "hw.cxgbe.num_vis=2" in loader.conf. num_vis > 2 is ok too, you'll
end up with multiple autonomous netmap-capable interfaces for every
port.
3) "dmesg | grep vcxl | grep netmap" to verify that the interface has
netmap queues.
4) Use any of the 'v' interfaces for netmap. pkt-gen -i vcxl<n>... .
One major improvement is that the netmap interface has a normal data
path as expected.
5) Just ignore the cxl interfaces if you want to use netmap only. No
need to bring them up. The vcxl interfaces are completely independent
and everything should just work.
---------------------
Approved by: re@ (gjb@)
Relnotes: Yes
Sponsored by: Chelsio Communications
Move the code that reads all the parameters to t4_init_sge_params in the
shared code. Use these per-adapter values instead of globals.
Sponsored by: Chelsio Communications
update to the latest internal shared code.
- Add a chip_params structure to keep track of hardware constants for
all generations of Terminators handled by cxgbe.
- Update t4_hw_pci_read_cfg4 to work with T6.
- Update the hardware debug sysctls (hidden within dev.<tNnex>.<n>.misc.*) to
work with T6. Most of the changes are in the decoders for the CIM
logic analyzer and the MPS TCAM.
- Acquire the regwin lock around indirect register accesses.
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
Each virtual interface has its own MAC address, queues, and statistics.
The dedicated netmap interfaces (ncxgbeX / ncxlX) were already implemented
as additional VIs on each port. This change allows additional non-netmap
interfaces to be configured on each port. Additional virtual interfaces
use the naming scheme vcxgbeX or vcxlX.
Additional VIs are enabled by setting the hw.cxgbe.num_vis tunable to a
value greater than 1 before loading the cxgbe(4) or cxl(4) driver.
NB: The first VI on each port is the "main" interface (cxgbeX or cxlX).
T4/T5 NICs provide a limited number of MAC addresses for each physical port.
As a result, a maximum of six VIs can be configured on each port (including
the "main" interface and the netmap interface when netmap is enabled).
One user-visible result is that when netmap is enabled, packets received
or transmitted via the netmap interface are no longer counted in the stats
for the "main" interface, but are not accounted to the netmap interface.
The netmap interfaces now also have a new-bus device and export various
information sysctl nodes via dev.n(cxgbe|cxl).X.
The cxgbetool 'clearstats' command clears the stats for all VIs on the
specified port along with the port's stats. There is currently no way to
clear the stats of an individual VI.
Reviewed by: np
MFC after: 1 month
Sponsored by: Chelsio
This commit contains large contributions from Giuseppe Lettieri and
Stefano Garzarella, is partly supported by grants from Verisign and Cisco,
and brings in the following:
- fix zerocopy monitor ports and introduce copying monitor ports
(the latter are lower performance but give access to all traffic
in parallel with the application)
- exclusive open mode, useful to implement solutions that recover
from crashes of the main netmap client (suggested by Patrick Kelsey)
- revised memory allocator in preparation for the 'passthrough mode'
(ptnetmap) recently presented at bsdcan. ptnetmap is described in
S. Garzarella, G. Lettieri, L. Rizzo;
Virtual device passthrough for high speed VM networking,
ACM/IEEE ANCS 2015, Oakland (CA) May 2015
http://info.iet.unipi.it/~luigi/research.html
- fix rx CRC handing on ixl
- add module dependencies for netmap when building drivers as modules
- minor simplifications to device-specific routines (*txsync, *rxsync)
- general code cleanup (remove unused variables, introduce macros
to access rings and remove duplicate code,
Applications do not need to be recompiled, unless of course
they want to use the new features (monitors and exclusive open).
Those willing to try this code on stable/10 can just update the
sys/dev/netmap/*, sys/net/netmap* with the version in HEAD
and apply the small patches to individual device drivers.
MFC after: 1 month
Sponsored by: (partly) Verisign, Cisco
netmap rx queues, and the "batchiness" of rx updates sent to the chip.
These knobs will probably become per-rxq in the near future and will be
documented only after their final form is decided.
MFC after: 1 month
It is disabled by default but users can set IFCAP_TXCSUM on the
netmap ifnet (ifconfig ncxl0 txcsum) to override netmap and force
the hardware to calculate and insert proper IP and L4 checksums in
outbound frames.
MFC after: 2 weeks
