o When we're resetting the board, make sure that we error out the pending
CCBs first. Otherwise the aha_cmd won't accept further commands, such
as those that are used to reset the card (AOP_INITIALIZE_MBOX). This
appears to cause a cascade failure where no more commands are possible
to the card.
o Reduce from 10s down to 1s the amount of time we're willing to tolerate
the card being awol. This helps the above case.
o Add some error checking to two commands issued in the probe.
I have a dim memory of gibbs@ trying to tell me about this problem a
few years ago, so pointy hat to imp@ for sitting on it so long.
in the log message for kern_sched.c 1.83 (which should have been
repo-copied to preserve history for this file), the (4BSD) scheduler
algorithm only works right if stathz is nearly 128 Hz. The old
commit lock said 64 Hz; the scheduler actually wants nearly 16 Hz
but there was a scale factor of 4 to give the requirement of 64 Hz,
and rev.1.83 changed the scale factor so that the requirement became
128 Hz. The change of the scale factor was incomplete in the SMP
case. Then scheduling ticks are provided by smp_ncpu CPUs, and the
scheduler cannot tell the difference between this and 1 CPU providing
scheduling ticks smp_ncpu times faster, so we need another scale
factor of smp_ncp or an algorithm change.
This quick fix uses the scale factor without even trying to optimize
the runtime divisions required for this as is done for the other
scale factor.
The main algorithmic problem is the clamp on the scheduling tick counts.
This was 295; it is now approximately 295 * smp_ncpu. When the limit
is reached, threads get free timeslices and scheduling becomes very
unfair to the threads that don't hit the limit. The limit can be
reached and maintained in the worst case if the load average is larger
than (limit / effective_stathz - 1) / 2 = 0.65 now (was just 0.08 with
2 CPUs before this change), so there are algorithmic problems even for
a load average of 1. Fortunately, the worst case isn't common enough
for the problem to be very noticeable (it is mainly for niced CPU hogs
competing with less nice CPU hogs).
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
that msync(2) is its only caller.
- Migrate the parts of the old vm_map_clean() that examined the internals
of a vm object to a new function vm_object_sync() that is implemented in
vm_object.c. At the same, introduce the necessary vm object locking so
that vm_map_sync() and vm_object_sync() can be called without Giant.
Reviewed by: tegge
are zx1 based machines and they don't particularly like it when we
poke at them with PC legacy code. The atkbd and psm devices were
disabled in the hints file so that one could enable them on machines
that support legacy devices, but that's not really something you can
expect from a first-time installer. This still leaves syscons (sc)
and the vga device, which were enabled by default and wrecking havoc
anyway. We could disable them by default like the atkbd and psm
devices, but there's really no point in pretending we're in a better
shape that way.
o pickup Giant in divert_packet to protect sbappendaddr since it
can be entered through MPSAFE callouts or through ip_input when
mpsafenet is 1
o add missing locking on output
o add locking to abort and shutdown
o add a ctlinput handler to invalidate held routing table references
on an ICMP redirect (may not be needed)
Supported by: FreeBSD Foundation
o add assertions in tcp_respond to validate inpcb locking assumptions
o use local variable instead of chasing pointers in tcp_respond
Supported by: FreeBSD Foundation
whether or not the isr needs to hold Giant when running; Giant-less
operation is also controlled by the setting of debug_mpsafenet
o mark all netisr's except NETISR_IP as needing Giant
o add a GIANT_REQUIRED assertion to the top of netisr's that need Giant
o pickup Giant (when debug_mpsafenet is 1) inside ip_input before
calling up with a packet
o change netisr handling so swi_net runs w/o Giant; instead we grab
Giant before invoking handlers based on whether the handler needs Giant
o change netisr handling so that netisr's that are marked MPSAFE may
have multiple instances active at a time
o add netisr statistics for packets dropped because the isr is inactive
Supported by: FreeBSD Foundation
PALM_4 initialisation hack. I've not confirmed it myself, but
seeing as we already don't use it for the Sony Clie_41, let's drop
it from the Clie_40 also and see what happens.
(Question: What about the Clie_S360 and Clie_NX60 devices? Do we
need to drop Palm4 from those as well? Possibly, but I've not had
any reports about those so I don't know.)
PR: kern/56575
MFC after: 3 days
is highly MD in an emulation environment since it operates on the host
environment. Although the setregs functions are really for exec support
rather than signals, they deal with the same sorts of context and include
files. So I put it there rather than create yet another file.
since there is no direct association between M:N thread and kse,
sometimes, a thread does not have a kse, in that case, return a pctcpu
from its last kse, it is not perfect, but gives a good number to be
displayed.
pmap_pte() and pmap_pte_quick(). The distinction being based upon the
locks that are held by the caller. When the given pmap is not the
current pmap, pmap_pte() should be used when Giant is held and
pmap_pte_quick() should be used when the vm page queues lock is held.
- When assigning to PMAP1 or PMAP2, include PG_A anf PG_M.
- Reenable the inlining of pmap_is_current().
In collaboration with: tegge
