in a P6 SMP system. Some MB bios'es don't set the registers up correctly
for the AP's. Additionally, set the memory between 0xa0000 and 0xbffff
as write combining.
savers are also modified so that they behave in the same way as the
blank saver on MDA and CGA, although it's not the way these screen
savers are supposed to work, but fading monitor and tickling green
monitor cannot be done on MDA and CGA, AFAIK. So, this is the second
best solution.
As of this change, the current state of support of screen savers is
summarized in the following table.
MDA CGA EGA VGA
blank OK OK NA OK
daemon OK OK OK OK
fade * * NA OK
green * * NA OK
snake OK OK OK OK
star OK OK OK OK
OK: works
NA: doesn't work, the module cannot be loaded for this adapter.
*: behave the same way as the blank saver.
As you can see, EGA is left out for now. But, we can do no better, as
EGA registers cannot be read...
Reviewed by: sos
shown to be harmful in that it results in the card not being detected
properly on warmboot due to the station address failing to be read
correctly from the NVRAM.
RST's being ignored, keeping a connection around until it times out, and
thus has the opposite effect of what was intended (which is to make the
system more robust to DoS attacks).
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
overruns (not that it was a problem, but it could be):
1) Doubled the number of receive buffers in the DMA chain to 64.
2) Do packet receive processing before transmit in the interrupt routine.
if it is in 10Mbps mode and gets certain types of garbage prior to
the packet header. The work-around involves reprogramming the
multicast filter if nothing is received in some number of seconds
(currently set at 15). As a side effect, implemented complete support
for multicasting rather than the previous 'receive all multicasts'
hack, since we now have the ability to program the filter table.
Fixed a serious bug which crept in with the timeout() changes;
the cookie was only saved on the first timeout() call in fxp_init()
and wasn't updated in the most common place in fxp_stats_update()
when the timeout was rescheduled. This bug would have resulted in
an eventual panic if fxp_stop() was called (which happens when any
interface flags are changed, for example).
Fixed a bug in Alpha support that would have caused the TxCB
descriptor chain to span a page boundry, causing serious problems
if the pages didn't happen to be contiguous.
Removed some gratuitous bit masking that was left over from an
older implementation.
Fixed a bug where too much was copied from the configuration
template, spilling over into memory that followed it.
Fixed handling of if_timer...it was cleared too early in some cases.
It seems I didn't count my 0's properly when adding the new masks into
icu_vector.s pushing SWI_AST_MASK off the end of the array and screwing
up the indexing for SWI_CLOCK_MASK.
Fix the bug icu_vector.s and also reformat the code in both icu_vector.s and
apic_vector.s so that it will be much harder to make the same mistake in
the future.
Submitted by: Bruce Evans <bde@zeta.org.au>
machine generates an NMI for each floating point error, just like an old XT.
Since it is ISA only, reading the EISA status port yields 0xff, which would
give a spurious EISA panic. The simplest thing to do is to ignore the 0xff.
operands that are set during seqeuncer program download instead of at
assembly time.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
operands that are set during seqeuncer program download instead of at
assembly time.
Convert the sequencer code to use" downloaded constants" for four run time
constants that vary depending on the board type. This frees up 4 bytes
of sequencer scratch ram space where these constants used to be stored and
also removes the additional instructions required to load their values
into the accumulator prior to using them.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
The scratch ram savings is important as the old code used to clober the
SCSICONF register on 274X cards which sits near the top of scratch ram
space. The SCSICONF register controls bus termination, and clobbering
it is not a good thing. Now we have 4 bytes to spare.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
1. Clustered I/O is switched by the MNT_NOCLUSTERR and MNT_NOCLUSTERW
bits of the mnt_flag. The sysctl variables, vfs.foo.doclusterread
and vfs.foo.doclusterwrite are deleted. Only mount option can
control clustered I/O from userland.
2. When foofs_mount mounts block device, foofs_mount checks D_CLUSTERR
and D_CLUSTERW bits of the d_flags member in the block device switch
table. If D_NOCLUSTERR / D_NOCLUSTERW are set, MNT_NOCLUSTERR /
MNT_NOCLUSTERW bits will be set. In this case, MNT_NOCLUSTERR and
MNT_NOCLUSTERW cannot be cleared from userland.
3. Vnode driver disables both clustered read and write.
4. Union filesystem disables clutered write.
Reviewed by: bde
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
(usually a couple of thousand) to 25. The measured impact on cache-hits
doesn't justify spending memory this way:
Target number of free vnodes versus namecache hit rate in % during a
make world:
10 98.5316
200 98.5479
500 98.5546
1000 98.5709
3000 98.6006
4000 98.6126
report slightly more than 64MB of total memory. This can happen due to the
total being the sum of both base and extended memory.
Submitted by: Alan Cox <alc@cs.rice.edu>
hash chain traversal isn't needed. This also allows untimeout to recompute
the hash to find the bucket that the entry to remove is stored in so
that each callout entry no longer needs to store that information.
Reviewed by: Nate Williams <nate@mt.sri.com>
