All armv6 processors are plenty fast enough for HZ=1000.
No changes are made for older arm systems, because some chips are a bit
wimpy for 1000 while others do fine, so it has to be set on a per-config
basis.
BREAK_TO_DEBUGGER if they have a serial console (most do). A burst of
serial line noise (such as unplugging a usb serial adapter) can look like
a break and drop a working system into the debugger. The alt break sequence
(<CR>~^B) works fine on both serial and non-serial consoles.
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
These are left over from long ago when there was no way to load modules
on early armv6 platforms, and when there was a build problem with ahc
that has long since been fixed, and they just keep getting copy-pasted
into new configs.
in effect due to r250753. That is sufficient for all SoCs with a 32 byte
cache line size. Systems with 64 byte cache lines will need the option;
that will be done in a separate commit.
Thanks to loos@ for pointing out r250753.
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
All these configs already exist in 10-stable. A few that don't (and
thus can't be MFC'd yet) will be committed separately.
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
such that when commenting/uncommentting lines, horizontal spacing is
maintained...
Also fix some minor comment formatting to line things up, etc...
Reviewed by: gnn, imp
MFC after: 1 week
