FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
where having this disabled was actually hurting us, since so many
BIOSes include legacy USB emulation that takes control of all usb
ports and only the ehci driver knows how to disable it.
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
It can be switched back once 5.3 is tested and released. Also turn on
PREEMPTION as many of the stability problems with it have been fixed.
MT5: 3 days.
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
NO_ADAPTIVE_MUTEXES. This option has been enabled by default on amd64 for
quite some time, and has been extensively tested on i386 and sparc64. It
shows measurable performance gains in many circumstances, and few negative
effects. It would be nice in t he future if adaptive mutexes actually went
to sleep after a certain amount of spinning, but that will require quite a
bit more testing.
known samples of broken chipsets that needed mixed mode in the first place
are so broken (ie: locks up) that we can't use IO APIC mode at all and it
needs to be turned off in the bios. So, the MIXED_MODE penalty on the
good chipsets gained nothing.
Approved by: re (scottl)
- turn on SMP in generic
- add 'device atpic' - this is unconditional on i386, but certain nvidia
based systems need to disable acpi because the reference bios seems to be
hosed. If acpi is disabled, we won't find the apic. amd64 has the
mptable code in a seperate compile option as well.
- turn sym back on, it doesn't fail to compile anymore.
Approved by: re
of "dumb" PCI-based serial/parallel boards get a hint how to enable
them.
I wasn't sure about the ia64, pc98, powerpc, and sparc64 archs whether
they'd support puc(4) or not.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
stolen from the ia64/ia32 code (indeed there was a repocopy), but I've
redone the MD parts and added and fixed a few essential syscalls. It
is sufficient to run i386 binaries like /bin/ls, /usr/bin/id (dynamic)
and p4. The ia64 code has not implemented signal delivery, so I had
to do that.
Before you say it, yes, this does need to go in a common place. But
we're in a freeze at the moment and I didn't want to risk breaking ia64.
I will sort this out after the freeze so that the common code is in a
common place.
On the AMD64 side, this required adding segment selector context switch
support and some other support infrastructure. The %fs/%gs etc code
is hairy because loading %gs will clobber the kernel's current MSR_GSBASE
setting. The segment selectors are not used by the kernel, so they're only
changed at context switch time or when changing modes. This still needs
to be optimized.
Approved by: re (amd64/* blanket)
