bttv's audio mux values.
Automatically locate the EEPROM i2c address and read the subsystem_vendor_id
from EEPROM and not the PCI registers.
Add NSMBUS checks around smbus/iicbus i2c bus code
Add GPIO mask for the audio mux to each card type.
Add CARD_ZOLTRIX and CARD_KISS from mailing list searches.
Tested by: Paul Reece <paul@fastlane.net.au>,
Ivan Brawley <brawley@internode.com.au> and
Gilad Rom <rom_glsa@ein-hashofet.co.il>
was available to the programmer to hold chip state information:
Use the SDID register instead of CTEST3. This change actually
simplifies the SCRIPTS code, but I'm not absolutely sure, that
it is OK for all variants of NCR chips around and all device
combinations. I have had this code running on several systems
with 53c810, 875 and 895 controllers for several months.
Suggested by: Gerard Roudier <groudier@club-internet.fr>
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
interrupt configuration reported. (I just discovered my vga card is
being configured for irq 5... :-) This is just reporting. The vga_isa
driver does the real work using the isa compat mappings.
Restore 0x710110b9 ("AcerLabs M15x3 Power Management Unit") - but only
if NALPM == 0.
Restore 0x00051166 ("Ross (?) host to PCI bridge") so that
fixbushigh_Ross() gets called.
Delete generic_pci_bridge(), it's been replaced by other mechanisms (see
the isab and pcib match/probes and the pci_bridge_type() function)
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
uses the AUI port with an on-board AUI to 10baseFL transceiver, not the
10baseT port like I had earlier suspected. The 3c900B-FL should be properly
supported now.
bug in the stats accounting (nicSendBDs counter was bogus when TX ring was
configured to be in host memory).
Update if_tireg.h to look for new firmware fix level.
* Make the network code in the bootstrap more chatty (helps debugging)
* Add nfs root stuff to cpu_rootconf(). I also added a check to make sure
it really was netbooting which allows the use of the same kernel for local
and network boots.
* Tweak the de driver so that it takes the speed setting from the console
for the alpha (some PWSs have broken de chipsets). This is the same
behaviour as NetBSD/alpha.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
resource. Avoids useless interrupts occurring between the allocation
of the interrupt resource and the final initialisation of the
kernel. Cause of these interrupts is unknown (a resuming device?).
- Try to unbreak what I broke by screwing with the tx queuing again.
I'm waiting for a few more people to test out this code and report back
before I move it into current. Hopefully it will be soon. Basically I
reverted to the old TX queuing strategy.
- Add experimental support for the 3c900B-FL (10mbps ST fiber). The card
should be detected properly and the 10baseFL mode supported, but again
I'm still waiting for word from a tester to see if this actually works.
It shouldn't affect the other cards though; all the differences are in
media selection.
- Set the TX start threshold register to get better performance.
- Increase the size of the RX and TX rings. UDP performance was pretty
bad because the TX ring was too small. Should be substantially better
now (I can saturate the link with either TCP or UDP now).
- Change some of the #defines to reflect proper 3Com ASIC names (boomerang,
cyclone, krakatoa, hurricane).
- Simplify and reorganize interrupt handler; ack all interrupts right
away and then process them. This avoids a potential race condition.
(Noted by Matt Dillon.)
- Reorganize the bridging code to eliminate using a goto to jump into
the middle of an if() {} clause. Sorry, that just made my brain itch.
- Use m_adj() in xl_rxeof().
- Make the payload alignment in xl_newbuf() the default (instead of
just conditionally defined for the alpha) to improve NFS performance
(avoids need for nfs_realign()).
from ever catching up to the transmit consumer index. We can't let this
happen because ti_txeof() depends on the assumption that producer == consumer
means the ring is empty, and producer != consumer means the ring has some
number of active descriptors in it.
This will allow software teletext/intercast/subtitles decoding
while watching a TV station.
Based on code from Hiroki Mori <mori@infocity.co.jp> but reworked by
myself.
Add new #ifdef. By defining BKTR_NO_MSP_RESET you can prevent the
MSP34xx being reset by the bt848 driver. This is handy
if you pre-initialise the MSP34xx stereo audio chip in another
operating system first (eg MS Windows).
Suggested by: Randal Hopper<aa8vb@ipass.net>
Suggested by: Yuri Gindin <yuri@xpert.com>
style pci drivers with a simple one-line change to use a module that
registers itself under new-bus and should in theory enable just about all
of the pci drivers to be loadable (kldload and loader(8)) but without
having the impact of converting the APIs yet.
This also fixes the problem of having undefined variables when only
new-style pci drivers are present.
Convert to new bus and bus dma.
Use latest PCI API.
bt_pci.c:
Fix a few bugs in how resourses are released left over from
when this driver was converted to new bus.
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
