build it on the i386 and alpha architectures, where this has been
set up (there is also a sparc64-bitops.h in sys/gnu/ext2fs, but it
appears to be broken and it is not linked up).
This should unbreak the sparc64 LINT build.
built by LINT. Also override a number of knobs for enabling and
disabling various modules in the ALL_MODULES case to further increase
LINT's module coverage.
Submitted by: ru
on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
from the tree until it is fixed. Since it is an atm driver, it isn't
commonly used so this will not negatively impact too many people.
harti can reconnect it when he resurfaces and corrects the en module
problems. This should allow snapshots to start succeeding again.
Reported by: lots of people
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
following changes have been done:
- stylify. The original code was too hard to read.
- get rid of a number of compilation options (Adaptec-only, Eni-only, no-DMA).
- more debugging features.
- locking. This is not correct yet in the absence of interface layer locking,
but is correct enough to not to cause lock order reversals.
- remove RAW mode. There are no users of this in the tree and I doubt that
there are any.
- remove NetBSD compatibility code. There was no way to keep NetBSD non-busdma
and FreeBSD busdma code together.
- if_en now buildable as a module.
This has been actively tested on sparc64 and i386 with ENI server and
client cards and an Adaptec card (thanks to kjc).
Reviewed by: mdodd, arr
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
Interface (SMAPI) BIOS, which is present on some IBM
Thinkpad models (560, 600, 770 to name a few.)
The SMAPI BIOS provides access to System Information,
System Configuration, and Power Management.
module dependency system rely on linker behaviour that is machine dependent
and not part of the elf spec, and only work by accident on other platforms.
Approved by: re
the supported platforms. We build it into GENERIC, and it is currently
listed on the supported module list for drivers.conf on i386, which
breaks the release build. This may fix the release build for RC1 on
i386.
Conspiracy of: re
