for limiting disk (actually filesystem) IO.
Note that in some cases these limits are not quite precise. It's ok,
as long as it's within some reasonable bounds.
Testing - and review of the code, in particular the VFS and VM parts - is
very welcome.
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5080
for all struct bio you get back from g_{new,alloc}_bio. Temporary
bios that you create on the stack or elsewhere should use this before
first use of the bio, and between uses of the bio. At the moment, it
is nothing more than a wrapper around bzero, but that may change in
the future. The wrapper also removes one place where we encode the
size of struct bio in the KBI.
When destroying a character device the si_devsw field is set to NULL
before all references are gone, to indicate the character device is
going away. This can cause a NULL-dereference fault inside physio().
The callers of physio() should own a thread reference on the cdev and
if si_devsw is seen as non-NULL, it is usable during the execution of
the function. Else an ENXIO error code is returned.
Reviewed by: kib
MFC after: 2 weeks
pbufs is a limited resource, and their allocator is not SMP-scalable.
So instead of always allocating pbuf to immediately convert it to bio,
allocate bio just here. If buffer needs kernel mapping, then pbuf is
still allocated, but used only as a source of KVA and storage for a list
of held pages.
On 40-core system doing many 512-byte reads from user level to array of
raw SSDs this change removes huge lock congestion inside pbuf allocator.
It improves peak performance from ~300K to ~1.2M IOPS. On my previous
24-core system this problem also existed, but was less serious.
Reviewed by: kib
MFC after: 2 weeks
- Remove excessive parenthesis
- Use KNF continuation indentation
- Cut down on excessive continuation lines
- More consistent style in messages
- Use uprintf() instead of printf()
Submitted by: bde
configure sa(4) to request no I/O splitting by default.
For tape devices, the user needs to be able to clearly understand
what blocksize is actually being used when writing to a tape
device. The previous behavior of physio(9) was that it would split
up any I/O that was too large for the device, or too large to fit
into MAXPHYS. This means that if, for instance, the user wrote a
1MB block to a tape device, and MAXPHYS was 128KB, the 1MB write
would be split into 8 128K chunks. This would be done without
informing the user.
This has suboptimal effects, especially when trying to communicate
status to the user. In the event of an error writing to a tape
(e.g. physical end of tape) in the middle of a 1MB block that has
been split into 8 pieces, the user could have the first two 128K
pieces written successfully, the third returned with an error, and
the last 5 returned with 0 bytes written. If the user is using
a standard write(2) system call, all he will see is the ENOSPC
error. He won't have a clue how much actually got written. (With
a writev(2) system call, he should be able to determine how much
got written in addition to the error.)
The solution is to prevent physio(9) from splitting the I/O. The
new cdev flag, SI_NOSPLIT, tells physio that the driver does not
want I/O to be split beforehand.
Although the sa(4) driver now enables SI_NOSPLIT by default,
that can be disabled by two loader tunables for now. It will not
be configurable starting in FreeBSD 11.0. kern.cam.sa.allow_io_split
allows the user to configure I/O splitting for all sa(4) driver
instances. kern.cam.sa.%d.allow_io_split allows the user to
configure I/O splitting for a specific sa(4) instance.
There are also now three sa(4) driver sysctl variables that let the
users see some sa(4) driver values. kern.cam.sa.%d.allow_io_split
shows whether I/O splitting is turned on. kern.cam.sa.%d.maxio shows
the maximum I/O size allowed by kernel configuration parameters
(e.g. MAXPHYS, DFLTPHYS) and the capabilities of the controller.
kern.cam.sa.%d.cpi_maxio shows the maximum I/O size supported by
the controller.
Note that a better long term solution would be to implement support
for chaining buffers, so that that MAXPHYS is no longer a limiting
factor for I/O size to tape and disk devices. At that point, the
controller and the tape drive would become the limiting factors.
sys/conf.h: Add a new cdev flag, SI_NOSPLIT, that allows a
driver to tell physio not to split up I/O.
sys/param.h: Bump __FreeBSD_version to 1000049 for the addition
of the SI_NOSPLIT cdev flag.
kern_physio.c: If the SI_NOSPLIT flag is set on the cdev, return
any I/O that is larger than si_iosize_max or
MAXPHYS, has more than one segment, or would have
to be split because of misalignment with EFBIG.
(File too large).
In the event of an error, print a console message to
give the user a clue about what happened.
scsi_sa.c: Set the SI_NOSPLIT cdev flag on the devices created
for the sa(4) driver by default.
Add tunables to control whether we allow I/O splitting
in physio(9).
Explain in the comments that allowing I/O splitting
will be deprecated for the sa(4) driver in FreeBSD
11.0.
Add sysctl variables to display the maximum I/O
size we can do (which could be further limited by
read block limits) and the maximum I/O size that
the controller can do.
Limit our maximum I/O size (recorded in the cdev's
si_iosize_max) by MAXPHYS. This isn't strictly
necessary, because physio(9) will limit it to
MAXPHYS, but it will provide some clarity for the
application.
Record the controller's maximum I/O size reported
in the Path Inquiry CCB.
sa.4: Document the block size behavior, and explain that
the option of allowing physio(9) to split the I/O
will disappear in FreeBSD 11.0.
Sponsored by: Spectra Logic
The previous method was to set the D_UNMAPPED_IO flag in the cdevsw
for the driver. The problem with this is that in many cases (e.g.
sa(4)) there may be some instances of the driver that can handle
unmapped I/O and some that can't. The isp(4) driver can handle
unmapped I/O, but the esp(4) driver currently cannot. The cdevsw
is shared among all driver instances.
So instead of setting a flag on the cdevsw, set a flag on the cdev.
This allows drivers to indicate support for unmapped I/O on a
per-instance basis.
sys/conf.h: Remove the D_UNMAPPED_IO cdevsw flag and replace it
with an SI_UNMAPPED cdev flag.
kern_physio.c: Look at the cdev SI_UNMAPPED flag to determine
whether or not a particular driver can handle
unmapped I/O.
geom_dev.c: Set the SI_UNMAPPED flag for all GEOM cdevs.
Since GEOM will create a temporary mapping when
needed, setting SI_UNMAPPED unconditionally will
work.
Remove the D_UNMAPPED_IO flag.
nvme_ns.c: Set the SI_UNMAPPED flag on cdevs created here
if NVME_UNMAPPED_BIO_SUPPORT is enabled.
vfs_aio.c: In aio_qphysio(), check the SI_UNMAPPED flag on a
cdev instead of the D_UNMAPPED_IO flag on the cdevsw.
sys/param.h: Bump __FreeBSD_version to 1000045 for the switch from
setting the D_UNMAPPED_IO flag in the cdevsw to setting
SI_UNMAPPED in the cdev.
Reviewed by: kib, jimharris
MFC after: 1 week
Sponsored by: Spectra Logic
but assumes that a thread reference was already obtained on the passed
device. Use the function from physio(), to avoid two extra dev_mtx
lock and unlock. Note that physio() is always used as the cdevsw
method, or is called from a cdevsw method, and the caller already owns
the reference.
dev_strategy() is left to keep KPI intact, but now it is implemented
as a wrapper around dev_strategy_csw().
Do some style cleanup in physio().
Requested and reviewed by: kan (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
In physio, check if device can handle unmapped IO and pass an
appropriately mapped buffer to the driver strategy routine. The
only driver in the tree that can handle unmapped buffers is one
exposed by GEOM, so mark it as such with the new flag in the
driver cdevsw structure.
This fixes insta-panics on hosts, running dconschat, as /dev/fwmem
is an example of the driver that makes use of physio routine, but
bypasses the g_down thread, where the buffer gets mapped normally.
Discussed with: kib (earlier version)
buf->b-dev.
Put a bio between the buf passed to dev_strategy() and the device driver
strategy routine in order to not clobber fields in the buf.
Assert copyright on vfs_bio.c and update copyright message to canonical
text. There is no legal difference between John Dysons two-clause
abbreviated BSD license and the canonical text.
- Create a new function bdone() which sets B_DONE and calls wakup(bp). This
is suitable for use as b_iodone for buf consumers who are not going
through the buf cache.
- Create a new function bwait() which waits for the buf to be done at a set
priority and with a specific wmesg.
- Replace several cases where the above functionality was implemented
without locking with the new functions.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
substitute BUF_WRITE(foo) for VOP_BWRITE(foo->b_vp, foo)
substitute BUF_STRATEGY(foo) for VOP_STRATEGY(foo->b_vp, foo)
This patch is machine generated except for the ccd.c and buf.h parts.
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
- Let physio take read/write compatible args and have it use uio->uio_rw
to determine the direction.
- physread/physwrite are now #defines for physio
- Remove the inversly named minphys(), dev->si_iosize_max takes over.
- Physio() always uses pbufs.
- Fix the check for non page-aligned transfers, now only unaligned
transfers larger than (MAXPHYS - PAGE_SIZE) get fragmented (only
interesting for tapes using max blocksize).
- General wash-and-clean of code.
Constructive input from: bde
d_maxio is replaced by the dev->si_iosize_max field which the driver
should be set in all calls to cdevsw->d_open if it has a better
idea than the system wide default.
The field is a generic dev_t field (ie: not disk specific) so that
tapes and other devices can use physio as well.
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
lockmgr locks. This commit should be functionally equivalent to the old
semantics. That is, all buffer locking is done with LK_EXCLUSIVE
requests. Changes to take advantage of LK_SHARED and LK_RECURSIVE will
be done in future commits.
Made a new (inline) function devsw(dev_t dev) and substituted it.
Changed to the BDEV variant to this format as well: bdevsw(dev_t dev)
DEVFS will eventually benefit from this change too.
