vendors that list the vendor ID in the proper byte order. The second
section is for vendors that get it backwards. The third is for what
appear to be 'random' ones (although 0xcxxx appears to be coherent
enough that maybe somebody else is assigning those numbers).
o AD1980 hook.
o ac97_fix_auxout.
and:
o Associate AC97_MIX_AUXOUT with SOUND_MIXER_OGAIN rather than
SOUND_MIXER_MONITOR.
o Add ac97_fix_tone to remove tone controls from mixer if invalid.
are all bogus, and the cards that don't decode things quite right
often have hundreds of them. This will fix starvation of small dmesg
buffers and allow better debugging to happen. I thought about adding
an override, but there is such a thing as too many knobs. :-)
- Fix up TX speed changes.
- Make mpi-350 cards sort-of work with new firmware. It RXs okay but TXs
only work for about 14 packets then fails to get an interrupt. The
TX watchdog fires. It has been reported that my hack for now doesn't
break cards with the older firmware. It appears my card has lost
the ability to RX or TX at all but other peoples cards work. I assume
it got damaged in tansport.
MFC: 1 week.
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
quietly discard them; this just permits them to be collected with bpf)
o add a counter for the number of rate control frames discarded when not in
monitor mode
o move the rx "too short" statistic in the stat structure so non-error rx stats
are together (NB: ABI change to apps that collect stats via driver ioctl)
mistakes (this mistake was not an issue because the length is only used to
decide whether or not to allocate a cluster)
o while here, move a beacon length comment to the "right place"
present, and non-zero when it is (or may be) absent. The test
cbb_child_present was backwards. However, typical usage in the tree
would cause it to do the right thing because the card really wasn't
there the OK flag would be turned on.
Also, assume that if any of these bits are turned on we don't have a
card, rather than requiring both of them in the suspend/resume
routines.
Noticed by: cognet
to what is in NetBSD. I have a few cards that tickles this bug, and
this just keeps us from panicing. It doesn't actually fix the problem
(that will happen once I figure out why some cards hate the address
their CIS is mapped to high memory).
A timecounter will be selected when registered if its quality is
not negative and no less than the current timecounters.
Add a sysctl to report all available timecounters and their qualities.
Give the dummy timecounter a solid negative quality of minus a million.
Give the i8254 zero and the ACPI 1000.
The TSC gets 800, unless APM or SMP forces it negative.
Other timecounters default to zero quality and thereby retain current
selection behaviour.
Correctly handle additional disks without BIOS partition tables.
Previously, vinum_scandisk stopped scanning additional disks for
native partitions after any good partition was found. This applies
to all platforms, but was a particular problem on systems without
BIOS partition tables.
Submitted by: harti
the hardware mutex if it is held. Re-add calls to Enable/Clear fixed events.
This is not known to have caused problems. Bug symptoms might have included
instability after an aborted suspend attempt or power/sleep buttons not
being enabled.
CP-168U board. It initializes and attaches in the same way as the
older (but higher performance) C168H. The only difference is the
board ID, which is 0x1681.
PR: kern/53548
Submitted by: regnauld@catpipe.net
MFC after: 1 week
the Palm device and the USB host controller deadlock. The USB host
controller is expecting an early-end-of-transmission packet with 0
data, and the Palm doesn't send one because it's already communicated
the amount of data it's going to send in a header (which ucom/uvisor
are oblivious to). This is the problem that has been known on the
pilot-link lists as the "[Free]BSD USB problem", but not understood.
Submitted by: Nathan J. Williams <nathanw@MIT.EDU>
for partly-aligned operations through /dev/crypto (unlikely)
o add missing case in iov code that never showed up because of the above bug
Submitted by: "Jason L. Wright" <jason@thought.net>
MFC after: 3 days
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
These are 10/100 only NICs found on the IBM Thinkpad R40E and
G40. These seem to be based on the BCM5705 MAC but with a PHY
that doesn't support 1000Mbps modes.
Submitted by: Igor Sviridov <sia@nest.org>
ioctls.
In the particular case of ptrace(), this commit more-or-less reverts
revision 1.53 of sys_process.c, which appears to have been erroneous.
Reviewed by: iedowse, jhb
to configure this correctly yields many watchdog timeouts even on lightly
loaded machines. This is a common complaint from users with Dell 1750
servers with built-in dual 5704 NICs.
the time the card is inserted and the time that the card is
configured. This can lead to interrupt storms. The O2Micro suggested
workaround is to route the card function interrupt to IRQ1. It
appears from my testing that this is an acceptable workaround for most
chipsets (there's still some issue with the ricoh chipset).
Also, only look at the NOT_A_CARD bit when the bridge tells us there's
a card present. At least one test caused this to be true after the
card was removed, but the author couldn't recreate it with the
workaround in place. The change is more conservative than the
previous code, but still has the work around that wasn't present in
the older code.
BGE_MACSTAT_MI_COMPLETE bit in the MAC status register as a link
change indicator. We turn this bit on now because some of the newer
chips need it, but it usually just means that reading/writing
an MII/GMII register has completed, not that a link change has
occured.
the standard.
1) When the bridge tells us that we have a card that isn't recognized, we
use the force register to force the CV_TEST to run. This test causes the
bridge to re-evaluate the card. Once this re-evaluation process happens,
we get a new interrupt that may say it is ready to process. We try this up
to 20 times. Tests have shown that this appears to correctly reset the
'Unknown card type' problem that I saw on my Sony PCG-505TS.
2) Take a page from OLDCARD and always read the CSC register in the ISR.
Some TI (and it seems maybe Ricoh) chipsets require this to behave
properly. This work around appears to work due to some power management
protocols that were improperly implemented. Maybe it can be removed when
this driver supports the full PME# protocol described in the standards.
3) Minor additional debug printf when debugging is enabled.
4) Minor additional commentary for things that are obvious only after study.
# I'm committing this from my Sony PCG-505TS using shared PCI interrupts
# and NEWCARD, but there are some issues with the Ricoh bridge still, but
# at least now I can boot with the card inserted and have it work.
PCG-505BX (for example) has one of those:
wi0: <Intersil Prism3> mem 0xf8000000-0xf8000fff at device 2.0 on pci2
wi0: 802.11 address: 00:02:8a:94:d8:73
wi0: using RF:PRISM3(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.5.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
has the same product id, but different vendor id. It also appears
that the MELCO's id should be 0x18a instead of 0x8a01. Fix this.
Submitted by: Shizuka Kudo-san
and up commands. When configuring the interface down only the
connections that are currently closing are deleted from the connection
table. When the interface is configured up, all connections that
are in the table are re-opened.
connections that have been open (and were not closing) when
the interface was stopped. This makes the behaviour of fatm(4) more like
the behaviour of en(4).
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
- Build SGL's for ATA_PASSTHROUGH commands
- Fallback to using the sgl_offset when the opcode is unknown for building
SGL's/
- Add ioctl calls for adding and removing units.
- Define previously undefined AEN's
- Allocate memory for the ioctl payload in multiples of 512bytes.
MFC after: 1 week
preparation for supporting the OPENVCC and CLOSEVCC ioctls which
are needed for ng_atm. This required some re-organisation of the code
(mostly converting array indexes to pointers). This also gives us
an array of open vccs that will help in using the generic GETVCCS handler.
the macro definition, and cause the generation of syntactically
incorrect code that gcc happens to accept.
Reviewed by: schweikh (mentor)
MFC after: 4 weeks
larger than normal frames, to account for the case where a bge(4) NIC
is used with VLANs. Since we set the IFCAP_VLAN_MTU flag, we must allow
reception of frames up to 1522 bytes in size rather than 1518.
Note that it is possible to work around this bug by doing:
# ifconfig bge0 mtu 1504
prior to configuring any VLAN interfaces.
recompiling the driver. See the comments near the top of "if_em.h"
for descriptions of these delays. Four new loader tunables control
the system-wide default values:
hw.em.tx_int_delay
hw.em.rx_int_delay
hw.em.tx_abs_int_delay
hw.em.rx_abs_int_delay
The tunables are specified in microseconds. The valid range is
0-67108 usec., and 0 means that the timer is disabled.
There are also four new sysctls (actually, a set of four for each
"em" device in the system) to query and change the interrupt delays
after the system is up:
hw.em0.tx_int_delay
hw.em0.rx_int_delay
hw.em0.tx_abs_int_delay (not present for 82542/3/4 adapters)
hw.em0.rx_abs_int_delay (not present for 82542/3/4 adapters)
It seems to be OK to change these values even while the adapter is
passing traffic.
Approved by: Prafulla Deuskar <pdeuskar@FreeBSD.ORG>
MFC after: 4 weeks
