free_vinum: Wait for daemon to stop by checking the
vinum_conf.flags & VF_DAEMONOPEN.
vinum_modevent:
When compiled with VINUMDEBUG, check if we have
forgotten to free any memory, and log an error if we
have.
vinumopen: Allow open of an empty subdisk (otherwise we can't
initialize it).
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
- When trying to map ports, if mapping TL_PCI_LOIO or TL_PCI_LOMEM fails,
try mapping the other one. Apparently, some ThunderLAN parts swap these
two registers while others don't.
- Add support for bitrate (non-MII) PHYs. If no MII-based PHY is found,
program the chip for bitrate mode. This is required for the TNETE110
part, which doesn't have MII support. (It's also obsolete, but there
are still some people out there who have them.) With this change and the
change above, the Compaq Netflex-3/P 10baseT/BNC board works correctly.
(Thanks to Matthew Dodd for getting me one of these cards.)
- Convert to bus_space_foo() for register accesses.
- Add changes to support FreeBSD/Alpha. I still have to actually test
this in my Alpha box so I'm not going to update /sys/alpha/conf/GENERIC
yet.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
VINUM_<object>CONFIG: return ENXIO rather than EFAULT if an object
doesn't exist.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
vinum_scandisk: increment drive use count when we find a good one.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
Remove unused (and braindead) functions volume_index, plex_index,
sd_index and drive_index.
Add a flag VF_CREATED for volumes. VF_NEWBORN was being used in two
capacities, and they clashed, my Lord, they clashed.
find_object: restructure the search loop as a result of the change in
variable use.
Decrement object use count in the remove_<object> functions, not in
the free_<object> functions, which are often called with partially
initialized (and uncounted) objects.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
* bus_setup_intr() as a wrapper for BUS_SETUP_INTR
* bus_teardown_intr() as a wrapper for BUS_TEARDOWN_INTR
* device_get_nameunit() which returns e.g. "foo0" for name "foo" and unit 0.
* device_set_desc_copy() malloc a copy of the description string.
* device_quiet(), device_is_quiet(), device_verbose() suppress probe message.
Add one method to the BUS interface, BUS_CHILD_DETACHED() which is called
after the child has been detached to allow the bus to clean up any memory
which it allocated on behalf of the child.
I also fixed a bug which corrupted the list of drivers in a devclass if
a driver was added to more than one devclass.
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
.gdbinit.crash contains a top-level .gdbinit suitable for debugging
crash dumps
.gdbinit.serial contains a top-level .gdbinit suitable for serial
debugging
Each of these two files reads the following files:
.gdbinit.kernel: This file contains general macros suitable for kernel
debugging. It is not related to vinum
.gdbinit.vinum: This file contains macros specific to debugging
vinum.
.gdbinit.paths: Contains information about the location of the source
and object files on the system.
.gdbinit.crash contains a top-level .gdbinit suitable for debugging
crash dumps
.gdbinit.serial contains a top-level .gdbinit suitable for serial
debugging
Each of these two files reads the following files:
.gdbinit.kernel: This file contains general macros suitable for kernel
debugging. It is not related to vinum
.gdbinit.vinum: This file contains macros specific to debugging
vinum.
.gdbinit.paths: Contains information about the location of the source
and object files on the system.
longjmp. I suspect that the occasional double panic may be the result
of incorrect parameters to longjmp. This happens, of course, like the
entire file, only with -DVINUMDEBUG.
give_sd_to_plex: Don't set Raid-5 subdisk state here.
config_subdisk: handle the name parameter correctly when the subdisk
was referenced in a previous plex definition. The
name parameter must come first.
Handle autosizing relatively correctly. There is
still a danger of losing drive space if problems
occur with an autosized subdisk.
Set state to empty, not up, when complete. This also
solves a nagging problem about enforcing the need to
initialize RAID-5 plexes.
config_plex: handle the name parameter correctly when the plex
was referenced in a previous volume definition. The
name parameter must come first.
Handle initial state better.
update_plex_config:
Calculate the trim factor for RAID-5 plexes correctly.
Set the number of down subdisks correctly when reading
from disk config.
Contributed-by: "Richard Seaman, Jr." <dick@tar.com>
Tested-by: Chris Piazza <cpiazza@home.net>
Tugrul Galatali <tugrul@ianai.BlackSun.org>
grog
This code includes lots of stuff for verbose probing. I'm not 100%
sure that the output of the verbose probe is correct, but everything
else works fine, and -CURRENT was broken for the 5591 before, so I'm
committing it anyway.
sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
if uio->uio_offset != -1. This fixes a problem with aio_read/write
and permits a straightforward implementation of pread/pwrite.
PR: kern/8669
Submitted by: John Plevyak <jplevyak@inktomi.com>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
the IP header (this would not work for bridged packets).
This has been fixed long ago in the 2.2 branch.
Problem noticed by: a few people
Fix suggested by: Remy Nonnenmacher
settings you've just sent them and return random values if you follow
the set by a get. This causes problems when you latter run a Tag-enabled
command when you've command tagged mode off.
kern.chroot_allow_open_directories = 0
chroot(2) fails if there are open directories.
kern.chroot_allow_open_directories = 1 (default)
chroot(2) fails if there are open directories and the process
is subject of a previous chroot(2).
kern.chroot_allow_open_directories = anything else
filedescriptors are not checked. (old behaviour).
I'm very interested in reports about software which breaks when
running with the default setting.
affects cases where there is a slave but no master. These bugs
were usually recovered from provided ATAPI was configured, but only
after lengthy delays. Configuring ATAPI still fixes some bugs for
non-atapi drives.
Don't wait for seek complete in wdreset(). If necessary for pre-ata
drives, it can be waited for later (we got it wrong by only looking
at it for drive 0 anyway). It is set as part of a historical
signature for ata drives but doesn't say anything useful about the
reset state. It is cleared as part of a non-historical signature
for atapi drives so that drivers which don't understand atapi drives
seem to see no drive. Waiting for it caused lengthy delays and
broke the status returned by wdreset() in cases where the master
was not an ata drive. Then the whole wdprobe() failed in some
cases where the recovery code didn't work.
Don't wait for drive ready in wdreset(). The considerations are
the same as for seek complete, except drive ready does say something
useful about the reset state of ata drives, and waiting for it
later is required anyway for such drives.
Lengthy delays can now be avoided by not configuring nonexistent
(ata) drives. Unfortunately, this breaks detection of atapi drives
in some configurations.
Recognize aic7895 controllers that have been "acquired" by a RAIDPort
card as normal aic7895s.
Recognize the aic7815 Raid Parity/Memory controller chip and notify
the user that it's RAID functionality will be ignored.
Don't mess with the IRQMS bit in the host control register unless
we are an aic7770 chip.
Use calling context to determine if the card is already paused when
we update the target message request bit field in controller scratch
ram. Looking at the paused bit in the HCNTRL register opened up a
race condition.
Insert delays in the target message request update routine as a temporary
work around for what looks like a chip bug. I'm still investigating this
one.
Fix the Abort/Abort Tag/BDR handler to pull its message from the message
buffer in our softc instead of attempting to get it from a register on
the controller. The message is never recorded by the controller in the
new message scheme.
Don't rely on having an SCB when a BDR occurs. We can issue these during
invalid reconnects to.
Fix a few cases where we were restarting the sequencer but then still
falling out of a switch statement to unpause the sequencer again.
This could cause us to mess up sequencer state if it generated another
pausing interrupt between the time of the restart and unpause.
Kill the 'transceiver settle' loop during card initialization. I
failed to realize that a controller that is not connected to any
cables will never settle or enable the SCSI transceivers at all.
The correct solution is to monitor the IOERR interrupt which indicates
that the transceiver state has changed (UW<->LVD).
Modify the aic7xxx assembler to properly echo input when stdin is not
a tty.
remove the splbio() around the call to launch read requests.
launch_requests:
Move the splbio() protection outside the entire launch_loop. The
previous location was causing problems with IDE drives, where the
call to the strategy routine often did not complete until after
complete_rqe deallocated the request structure.
Solution-independently-found-by: Russell Neeper <r-neeper@tamu.edu>
Problem-reported-by: Vallo Kallaste <vallo@matti.ee>
John Saunders <john@nlc.net.au>
Bernd Walter <ticso@cicely.de> (maybe)
Check for partition types FS_VINUM and FS_UNUSED. Accept both, but
complain about FS_UNUSED. At a later date, only FS_VINUM will be
accepted.
Threatened-since: over a year
Add a flag `force' (VF_FORCECONFIG) to force name changes of
existing drives.
config_drive:
If the drive already has a vinum label, and name doesn't match the
specified drive, do it anyway if the 'force' flag is specified.
finish_config:
Reset the `force' flag.
Continually-tripped-over-by: Karl Pielorz <kpielorz@tdx.co.uk>
give_sd_to_drive:
If the drive is down, take the subdisk down and don't try to fix
things.
update_plex_config:
Don't try to update the config parameters of a plex which isn't
fully configured (state plex_init or plex_unallocated).
Correctly calculate the amount to trim off a striped or RAID-5 plex
whose size is not a multiple of the stripe size.
/usr/sbin/sysctl -> ${DESTDIR}/sbin/sysctl in some versions of 2.2,
and this link was broken if DESTDIR was set.
Added a SYMLINKS macro. This works the same as LINKS, except it
creates symlinks and the linked-to pathname may be relative. This
is more flexible than LN_FLAGS, since it supports installing
symlinks independently of hard links.
Use `ln -f[s] ...' instead of `rm -f ...; ln [-s] ...' for LINKS and
SYMLINKS. This is equivalent if the target is neither a directory nor
a symlink to a directory.
PR: 8279
Remove more (redundant) map timestamp increments from properly
synchronized routines. (Changed: vm_map_entry_link, vm_map_entry_unlink,
and vm_map_pageable.)
Micro-optimize vm_map_entry_link and vm_map_entry_unlink, eliminating
unnecessary dereferences. At the same time, converted them from macros
to inline functions.
compiled with or without debugging support. This enables us to catch
(fatal) mismatches between the kernel and userland.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
Add VINUM_BIGDRIVE for pretending we have macho hardware.
pretends that each drive is 100 times as large as it really is. Not
for use at home.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
This solved a problem where 'vinum resetconfig' only reset half
the drives.
Reported-by: Brad Knowles <blk@skynet.be>
Karl Pielorz <kpielorz@tdx.co.uk>
Change the super device. We now have three super devices:
1. The normal superdevice used by vinum(8).
2. The superdevice used by vinum(8) when compiled with debug support.
3. The superdevice used by the daemon.
This method allows vinum(8) to determine debug mismatches. Also check
correctly for the device type. The old code did not check all bits of
the minor number.
Reported-by: a cast of thousands, most recently by Brad Knowles
<blk@skynet.be>.
address) so that the first 16MB of physical memory is allocated
last rather than first. On large-memory machines, this avoids
the exhaustion of low physical memory before isa_dmainit has run.
for passing in their own data space and associated page table information.
Update the support files so that any pages in the vm86 page table are
mapped, rather than just one page.
Restore the E820 memory probe, and have it use the new interface.
of private_tss, and there's no need to use a bit array. Also fixes
the problem of using `je' after btrl, since cmpl sets ZF.
Noticed by: Luoqi, on -current
with the new boot loader configuration process. I got a lot of
help from Daniel Sobral, and both Dan and I got help from Mike
Smith. This really belongs in Warner's UPDATING, but he's not
been answering his email recently, so that will wait a little.
Robert Nordier also gave me a lot of help, but he hasn't seen the
last version, and can't be blamed for my errors.
Approved by: jkh
Reviewed by: Mike Smith
gave yet another internal register layout model for what is
*still* the same architecture. I hope they saved billyuns of gates
'coz otherwise this is *really* annoying.
thwank in register layout goop). A different mboxcmd approach. Some PDB change
infrastructure. Some better management of loopdown/loopup events (keep them
distinct from resource starvation for simq freeze/unfreeze actions).
