Support is working on the Silicon Image SiI3124/3132.
Support is working on some AHCI chips but far from all.
Remember this is WIP, so test reports and (constructive) suggestions are welcome!
for a configurable number of seconds, spin the disk down. Spin it back
up on the next request.
Notice that the timeout is only armed by a request, so to spin down a
disk you may have to do:
atacontrol spindown ad10 5
dd if=/dev/ad10 of=/dev/null count=1
To disable spindown, set timeout to zero:
atacontrol spindown ad10 0
In order to debug any trouble caused, this code is somewhat noisy on the
console.
Enabling spindown on a disk containing / or /var/log/messages is not
going to do anything sensible.
Spinning a disk up and down all the time will wear it out, use sensibly.
Approved by: sos
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
Note: this might print failure messages on some systems, unfortunatly
the info from the device, stating if flushing is supported, cannot be trusted
so the operation is always issued on all devices, just in case...
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
Add code to properly detach/attach disks that are part of a RAID.
Mark a disk that is attached on an ATA channel belonging to a
RAID as a spare disk that can be used for rebuilding failed RAID1's.
Add support for rebuilding failed RAID1's.
Several fixes to the detach/attach code.
For replacing a disk in a failed RAID1 do the following:
Find the controller channel# of the failed disk.
Exec 'atacontrol detach <channel#>' to free the disk from the system.
Replace the failed disk with a new one of at least the same size.
If your have your disks in drawers/enclosures this can be done with
the system still running.
Exec 'atacontrol attach <channel#>' to add the disk to the system and
mark it as a valid spare for rebuild.
Exec 'atacontrol rebuild <array#>'
The system will rebuild the array on the fly, the array can still
be used during this, although with slower performance.
Please let me know of any problems with this!
Sponsored by: Advanis Inc.
MFC after: 2 weeks
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
Proberly fail outstanding bio requests on devices that are detached.
This makes it possible to change between disk/cdrom/dvd/whathaveyou
in a notebook, just by suspending it, changing the device in the
bay (or what you model calls it), unsuspend and the ATA driver
will figure out what disappeared and properly fail those, and attach
any new devices found.
IBM's DPTA and DTLA series of drives (no other disk vendors are known
to support this) on non-Promise controllers (promise controllers lockup
when given the tagged queuing specific commands).
It gives especially master/slave comboes about 5% better performance.
Add support for the Promise ATA100 OEM chip (pdc20265)
Add support for the Cyrix 5530
Change the way status is read from the drives, use the alternate
status reg when possible.
Better support for DEVFS, the acdXtY devices are now created when needed.
Lots of little cleanups.
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
was needed to make attach/detach of devices work, which is
needed for the PCCARD support.
(PCCARD support is still not working though, more to come on that)
Support the CMD646 chip which is used on many alphas, sadly only
in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes.
Lots of cosmetic fixes here and there.
Sorry for the size of this megapatchfromhell but it was not
possible otherwise...
newbus patches based on work from: dfr (Doug Rabson)
correctly on both master and slave.
Smash together the ata_params & atapi_params structures as they
are more or less equal anyways.
Get rid of the last SYSINIT's in here.
on all combinations (I hope)...
Add DMA support for the AMD 756 chip (K7 chipset) this is actually the
same as the VIA 82C686 chip (the ATA part that is).
Treat the intel MX chipset PIIX as a PIIX4
Allow UDMA on all disks that say they can handle it.
Cleanup probe printf's a bit
Remove alot of the old #ifdef DEBUG crap.
On UDMA CRC errors retry operation as it might be a fluke, if not fall
back to PIO mode on the failing drive. If you get alot of these your
cabeling is most likely not good enough.
On HARD error using DMA, retry once using PIO, if it succeds using PIO
fall back to PIO mode on the failing drive.
their HotRod controller and on SIIG PCI ultra DMA controller. These
changes also made lots of the Promise code go away, its all much more
generic this way.
Get rid of atapi_immed_cmd, instead use the queue to move atapi commands
from interrupt context if nessesary, the entire atapi layer has
gotten an overhaul.
Lots of fixes to utililize the new features in subr_disk.c etc, and
get rid of the last biots of softc arrays in the drivers, the
only one left is atadevices which cannot easily go away (yet).
Use our own malloc names, its a lot easier to track memory usage this way.
General cleanup overall.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
The atapi subsystem has gotten better error handeling and timeouts,
it also tries a REQUEST SENSE command when devices returns errors,
to give a little more info as to what went wrong. It might be a
little verbose for now, but I'm interested in as much feedback on
errors as possible, especially timeouts, as I'm a bit in doubt if
I've chosen resonable default values everywhere.
The disk driver has been changed a bit to prepare for tagged queing,
which is next on my list.
The disk driver has grown a dump routine, I got one implementation
from Darrell Anderson <anderson@cs.duke.edu> which also did
partial dumps (usefull on big memory machines) I left out the
partial stuff for now, and changed the rest alot to fit into the new
ad_request framework.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
Fixed problems:
LS120/ZIP drives still currupted data.
Reworked once again, buffered I/O is just ignoring any sizehints
it is given :(
Now the atapifd driver splits up requests for devices that has
limitted transfer size.
ISA only configs fails on boot with interrupt timeouts.
The new-bus integration introduced a bug where the softc ptr
was lost during the probe.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
reports on those most welcome!
Fixed problems:
Hang on probe on "fantom" devices.
The probe now use a timeout to avoid hangs if no interrupt
is recevied.
There has also been more general code clenaups, and some reorgs.
