The QCA9565 is a 1x1 2.4GHz 11n chip with integrated on-chip bluetooth.
The AR9300 HAL already has support for this chip; it just wasn't
included in the probe/attach path.
Tested:
* This commit brought to you over a QCA9565 wifi connection from
FreeBSD.
* .. ie, basic STA, pings, no iperf or antenna diversity checking just yet.
The HAL already included the STBC fields; it just needed to be exposed
to the driver and net80211 stack.
This should allow single-stream STBC TX and RX to be negotiated; however
the driver and rate control code currently don't do anything with it.
* Finish adding the HAL capability to announce whether a NIC supports
spectral scan or not;
* Add spectral scan methods to the HAL structure;
* Add HAL_SPECTRAL_PARAM for configuration of the spectral scan logic.
The capability ID and HAL_SPECTRAL_PARAM struct are from Qualcomm
Atheros.
This fixes the incorrect slot (and likely ACK/RTS timeout) values
which I see when enabling half/quarter rate support on the AR9280.
The resulting math matches the expected calculated default values.
The existing method for testing for MRR is to call the "SetupXTXDesc"
HAL method and see if it returns AH_TRUE or AH_FALSE. This capability
explicitly lists what number of multi-rate attempts are possible.
"1" means "one rate attempt supported".
to being more generic.
Other embedded SoCs also throw the configuration/PCI register
info into flash.
For now I'm just hard-coding the AR9280 option (for on-board AR9220's on
AP94 and commercial designs (eg D-Link DIR-825.))
TODO:
* Figure out how to support it for all 11n SoC NICs by doing it in
ar5416InitState();
* Don't hard-code the EEPROM size - add another field which is set
by the relevant chip initialisation code.
* 'owl_eep_start_loc' may need to be overridden in some cases to 0x0.
I need to do some further digging.
The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.
This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.
Obtained by: Linux, Atheros
The AR5008/AR9001 series NICs have a bug where BB register reads
will occasionally be corrupted. This could cause issues with things
such as ANI, which adjust operational parameters based on the
BB radio register reads. This was introduced in the AR5008 chip
and fixed with the first released AR9002 series NIC (AR9280v2.)
A followup commit will implement the acutal WAR when reading
BB registers. I'm still not sure how I'll implement it - whether
it should be done in the osdep layer, or whether it should just
live in the AR5416 HAL. Either way, they can use this capability
bit to determine whether to implement the WAR or not.
Thankyou to various sources inside Atheros who have helped me track
down what this particular issue is.
Obtained from: Atheros
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
and the Atheros reference code.
The radar detection code needs to know what the current DFS domain is.
Since net80211 doesn't currently know this information, it's extracted
from the HAL regulatory domain information.
The specifics:
* add a new ath_dfs API hook, ath_dfs_init_radar_filters(), which
updates the radar filters whenever the regulatory domain changes.
* add HAL_DFS_DOMAIN which describes the currently configured DFS domain .
* add a new HAL internal variable which tracks the currently configured
HAL DFS domain.
* add a new HAL capability, HAL_CAP_DFS_DMN, which returns the currently
configured HAL DFS domain setting.
* update the HAL DFS domain setting whenever the channel setting is
updated.
Since this isn't currently used by any radar code, these should all
be no-ops for existing users.
Obtained from: Atheros
Submitted by: KBC Networks, sibridge
Approved by: re (kib, blanket)
Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.
The particulars:
* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.
The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.
Obtained from: Linux, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
ctl/ext noise floor values.
This routine doesn't check to see whether the radio is MIMO
capable - instead, it simply returns either the raw values,
the "nominal" values if the raw values aren't yet available
or are invalid, or '0' values if there's no valid channel/
no valid MIMO values.
Callers are expected to verify the radio is a MIMO radio
(which for now means it's an 11n chipset, there are non-11n
MIMO chipsets out there but I don't think we support them,
at least in MIMO mode) before exporting the MIMO values.
From the ath9k source:
==
11N: we can no longer afford to self link the last descriptor.
MAC acknowledges BA status as long as it copies frames to host
buffer (or rx fifo). This can incorrectly acknowledge packets
to a sender if last desc is self-linked.
==
Since this is useful for pre-AR5416 chips that communicate PHY errors
via error frames rather than by on-chip counters, leave the support
in there, but disable it for AR5416 and later.
Linux ath9k only enables this for AR9280 and later NICs; so
create a capability for it so it isn't enabled for earlier
NICs.
Enabling hardware PS-POLL support will come in a later commit
and will be disabled by default.
rather than duplicating them for the v14 (ar5416+) and v4k (ar9285) codebases.
Further chipsets (eg the AR9287) have yet another EEPROM format which will use
these routines to calculate things.
It's used to calculate:
* the initial per-rate entries for short/long preamble ACK durations;
* packet durations for TDMA slot decisions;
* RTS/CTS protection durations;
* updating the duration field in the 802.11 frame header
This way invalid durations will generate a warning, prompting for it to be
fixed.
The higher levels (net80211, if_ath, ath_rate) need this to make correct
choices about what MCS capabilities to advertise and what MCS rates are
able to be TXed.
In summary:
* AR5416 - 2/3 antennas, 2x2 streams
* AR9160 - 2/3 antennas, 2x2 streams
* AR9220 - 2 antennas, 2x2 sstraems
* AR9280 - 2 antennas, 2x2 streams
* AR9285 - 2 antennas but with antenna diversity, 1x1 stream
This will eventually be used by rate control modules and by the TX
code for calculating packet duration when handling rts/cts protection.
Obtained from: sam@, rpaulo@, linux ath9k
This, along with an initval change which will appear in a subsequent commit,
fixes bus panics that I have been seing with the AR9220 on a Routerstation Pro
(AR7161 MIPS board.)
Obtained from: Linux ath9k
PR: kern/154220
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
o add HAL_CAP_BSSIDMATCH to identify parts that have the support for
disabling bssid match
o honor capability for set/get rx filter
o use HAL_CAP_BSSIDMATCH in driver to decide whether to use the bssid
match disable or fall back to promisc mode
Reviewed by: rpaulo
Approved by: re (rwatson)
