Taking over the sector following the MBR causes problems on some
machines, and the actual gains are fairly small in terms of how
the space is presently used.
Since we need a number of further features (eg. handling extended
partitions) that can't be readily accommodated in the basic boot0
design anyway, rather choose to implement the additional stuff
separately and concentrate on compatibility rather than features
here.
to allow commonality between varying platforms. This is a step
towards parsing the diskless configuration information with MI code
inside the kernel.
Export the interface hardware address to the kernel, so that it is possible
to determine the boot interface with certainty.
Export the NFS filehandle for the root mount to the kernel, so that the
kernel does not need to perform a mount RPC call.
BOOT_BTX_NOHANG, then BTX will be compiled with the appropriate flags so
that it reboots after a fault instead of hanging forever.
Requested by: ps
Approved by: rnordier
identifier to the DHCP server. Now you can check for this string
in your dhcp configuration to decide whether you will hand out a
lease to the client or not.
to 0x600 via a 'rep movsw'. Once that was done, %cx was zero, so we could
simply use 'movb' to update the lower byte of %cx in preparation for
zeroing out the fake partition entry used to boot to other drives via F5.
Well, in the new boot0, we don't actually relocate ourselves, instead it
is easier to create the fake partition entry first and then just use it to
get the BIOS to load all of boot0 into memory at 0x600. However, since we
aren't doing the relocate code anymore, we don't know that %cx == 0 when
we hit the 'movb' to setup %cx for clearning the fake partition entry.
Thus, if %ch != 0 when the BIOS started boot0, then it would end up zeroing
a lot more memory than just 8 words. The solution is to do a word move of
$8 into %cx.
Debugging help from: David Wolfskill <dhw@whistle.com>
Linux kernel image, and is designed to be dropped into a Linux system
and booted via LILO. Once booted, the user is greeted by the FreeBSD
loader. This still isn't quite complete, as the the root= specification
from LILO isn't currently passed to the loader yet.
- Autodetection and support of the BIOS EDD extensions to work around the
1024 cylinder limit on all but really ancient BIOS's.
- To work around some BIOS's which break when EDD is used with older drives,
we only attempt to use EDD if the cylinder is > 1023.
- Since this new code required more space than we had left, expand boot0 to
2 sectors (1024 bytes) in length.
- Add support for boot0 being multiple sectors using predefined constants.
If boot0 needs to be extended in the future, all that is required is
bumping the NUM_SECTORS constant.
- Now that we have more room to work with, add a few more fs type
descriptions while making others more verbose.
use the BIOS Equipment List to determine how many hard drives are
installed and if the drive number we received in %dl is valid.
- Don't bother to disable interrupts when setting up the stack. The 8086
and beyond implicitly disable interrupts after an instruction that sets
%ss (for example, a pop or a mov) so that you can safely set %ss and %sp
in two consecutive instructions. An exception to this is the lss
instruction, which can set both registers simultaneously and thus doesn't
need this hack.
- Add support for EDD BIOS extensions to support booting off of hard drives
of nearly arbitrary length.
- Add in support for the EDD (Enhanced Disk Drive) BIOS extensions to
use LBA mode for accessing drives past cylinder 1024. This should allow
us to load a kernel from anywhere on a newer drive up to 2 TB. Part
of this came from the PR below.
PR: i386/13847
Submitted by: Tor Egge <Tor.Egge@fast.no>
theory, this should allow the K7V Athlon motherboard to boot ok with boot
virus protection enabled. However, I have no hardware to test this. It
shouldn't break anything though. :)
Prodded by: Kelly Yancey <kbyanc@posi.net>
