the changes. Make sure that pci_alloc_msix() does give us the vectors
we need and fall back to MSI when it doesn't, also release any that
were allocated when insufficient.
MFC after: 3 days
ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however it does result in different behavior in the
ioctl routine when you are using a module vs static, and I
think the behavior should be the same.
MFC after: 3 days
irrespective of the setting of lem_rx_process_limit, while
giving a chance to the taskqueue scheduler to act after
each chunk.
This makes lem_rxeof similar to the one in if_em.c and if_igb.c .
if_lem.c and if_em.c: add a sysctl to manually configure the
'itr' moderation register.
Approved by: Jack Vogel
well as enabled when necessary. And simplify the checksum routine
itself, adding UDP bit to the test. Thanks to Kevin Lo for pointing
out the problems and code suggestions.
done in ixgbe, thanks to Mike Karels for this fix. When exiting
promiscuous mode MPE bit was being unconditionally cleared, this
should not be done if we are in MAX multicast groups.
the older if_start/non-multiqueue interface from the stack. This
is not the default, but can be turned on in the Makefile now regardless
of the OS level to allow either testing or use of ALTQ.
MFC after: one week
- bear with me, there are lots of white space changes, I would not
do them, but I am a mere consumer of this stuff and if these drivers
are to stay in shape they need to be taken.
em driver changes: support for the new i217/i218 interfaces
igb driver changes:
- TX mq start has a quick turnaround to the stack
- Link/media handling improvement
- When link status changes happen the current flow control state
will now be displayed.
- A few white space/style changes.
lem driver changes:
- the shared code uncovered a bogus write to the RLPML register
(which does not exist in this hardware) in the vlan code,this
is removed.
of the newer drivers. The basic problem was
that the driver was pulling the mbuf off the
drbr ring and then when sending with xmit(), encounting
a full transmit ring. Thus the lower layer
xmit() function would return an error, and the
drivers would then append the data back on to the ring.
For TCP this is a horrible scenario sure to bring
on a fast-retransmit.
The fix is to use drbr_peek() to pull the data pointer
but not remove it from the ring. If it fails then
we either call the new drbr_putback or drbr_advance
method. Advance moves it forward (we do this sometimes
when the xmit() function frees the mbuf). When
we succeed we always call advance. The
putback will always copy the mbuf back to the top
of the ring. Note that the putback *cannot* be used
with a drbr_dequeue() only with drbr_peek(). We most
of the time, in putback, would not need to copy it
back since most likey the mbuf is still the same, but
sometimes xmit() functions will change the mbuf via
a pullup or other call. So the optimial case for
the single consumer is to always copy it back. If
we ever do a multiple_consumer (for lagg?) we
will need a test and atomic in the put back possibly
a seperate putback_mc() in the ring buf.
Reviewed by: jhb@freebsd.org, jlv@freebsd.org
This prevents quad igb card on high core machines, without any nmbcluster or
igb queue tuning wedging the boot process if all nics are configured.
Reviewed by: jfv
Approved by: pjd (mentor)
MFC after: 1 week
fail or not. The mbuf pointer is no longer valid, so
can't be reused after.
Fix igb_mq_start() where mbuf pointer was used after
drbr_enqueue().
This eventually leads us to all invocations of
igb_mq_start_locked() called with third argument as NULL.
This allows us to simplify this function.
Submitted by: Karim Fodil-Lemelin <fodillemlinkarim gmail.com>
Reviewed by: jfv
device drivers that used to provide this feature.
This is a subset of 241856 (which was reverted)
Reviewed by: des
Approved by: cperciva (implicit)
MFC after: 1 week
tree used it incorrectly, which lead to inaccurate overrated
if_obytes accounting. The drbr(9) used to update ifnet stats on
drbr_enqueue(), which is not accurate since enqueuing doesn't
imply successful processing by driver. Dequeuing neither mean
that. Most drivers also called drbr_stats_update() which did
accounting again, leading to doubled if_obytes statistics. And
in case of severe transmitting, when a packet could be several
times enqueued and dequeued it could have been accounted several
times.
o Thus, make drbr(9) API thinner. Now drbr(9) merely chooses between
ALTQ queueing or buf_ring(9) queueing.
- It doesn't touch the buf_ring stats any more.
- It doesn't touch ifnet stats anymore.
- drbr_stats_update() no longer exists.
o buf_ring(9) handles its stats itself:
- It handles br_drops itself.
- br_prod_bytes stats are dropped. Rationale: no one ever
reads them but update of a common counter on every packet
negatively affects performance due to excessive cache
invalidation.
- buf_ring_enqueue_bytes() reduced to buf_ring_enqueue(), since
we no longer account bytes.
o Drivers handle their stats theirselves: if_obytes, if_omcasts.
o mlx4(4), igb(4), em(4), vxge(4), oce(4) and ixv(4) no longer
use drbr_stats_update(), and update ifnet stats theirselves.
o bxe(4) was the most correct driver, it didn't call
drbr_stats_update(), thus it was the only driver accurate under
moderate load. Now it also maintains stats itself.
o ixgbe(4) had already taken stats from hardware, so just
- drop software stats updating.
- take multicast packet count from hardware as well.
o mxge(4) just no longer needs NO_SLOW_STATS define.
o cxgb(4), cxgbe(4) need no change, since they obtain stats
from hardware.
Reviewed by: jfv, gnn
- Use a dedicated task to handle deferred transmits from the if_transmit
method instead of reusing the existing per-queue interrupt task.
Reusing the per-queue interrupt task could result in both an interrupt
thread and the taskqueue thread trying to handle received packets on a
single queue resulting in out-of-order packet processing and lock
contention.
- Don't define ixgbe_start() at all where if_transmit is used.
Tested by: Vijay Singh
Reviewed by: jfv
MFC after: 2 weeks
adapter->dropped_pkts instead of if_ierrors because if_ierrors is
overwritten by hw stats collection.
Submitted by: Andrew Boyer <aboyer@averesystems.com>
Reviewed by: Jack F Vogel <jfv@freebsd.org>
MFC after: 2 weeks
#defines. This also has the advantage that it makes the names more
compact, iand also allows us to correct the non-uniform naming of
the PCIM_LINK_* defines, making them all consistent amongst themselves.
This is a mostly mechanical rename:
s/PCIR_EXPRESS_/PCIER_/g
s/PCIM_EXP_/PCIEM_/g
s/PCIM_LINK_/PCIEM_LINK_/g
When this is MFC'd, #defines will be added for the old names to assist
out-of-tree drivers.
Discussed with: jhb
MFC after: 1 week
"m_getjcl:invalid cluster type" that occurred some
time back with the igb driver. This happens often when
booting over the net. I believe the NIC hardware is left
in a warm state when handed over to the driver, and a stray
RX interrupt happens earlier than the code is prepared for
it to happen. This change was verified to fix the problem,
its kind of a bandaid... but it is similar to what was done
in the igb code.
packet delivery, always enqueue when possible. Also
correct the DEPLETED test as multiple bits might be
set. Thanks to Randall Stewart for the changes!
system with sparse CPU IDs, you can have a valid CPU ID > mp_ncpus (e.g. if
you have two CPUs 0 and 4, with mp_maxid == 4 and mp_ncpus == 2).
Introduced at svn r235210
Submitted by: jhb@
Reviewed by: jfv@
when used in qemu (and this driver is for non-PCIe cards,
so probably its largest use is in virtualized environments).
Approved by: Jack Vogel
MFC after: 3 days
setting in the igb and em driver. This was necessitated by
a shared code change that I was given late in the game, a data
type changed from bool to int, in the last update I dealt with
it by a cast, but it was pointed out (thanks jhb) that there
was a potential problem with this. John suggested this safer
approach, and it is fine with me...
MFC after:2 days (to catch the 9.1 update)
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
as possible when using more than one igb(4) adapter. This
means that queues will not be bound to the same CPUs if
there are more CPUs availble.
This is only applicable to a system that has multiple interfaces.
Obtained from: Yahoo! Inc.
MFC after: 3 days
portions were already reapplied in r233708:
- Use a dedicated task to handle deferred transmits from the if_transmit
method instead of reusing the existing per-queue interrupt task.
Reusing the per-queue interrupt task could result in both an interrupt
thread and the taskqueue thread trying to handle received packets on a
single queue resulting in out-of-order packet processing.
- Call ether_ifdetach() earlier in igb_detach().
- Drain tasks and free taskqueues during igb_detach().
MFC after: 1 week
- Do not define the foo_start() methods or set if_start in the ifnet if
multiq transmit is enabled. Also, set if_transmit and if_qflush before
ether_ifattach rather than after when multiq transmit is enabled. This
helps to ensure that the drivers never try to mix different transmit
methods.
- Properly restart transmit during resume. igb(4) was not restarting it
at all, and em(4) was restarting even if the link was down and was
calling the wrong method if multiq transmit was enabled.
- Remove all the 'more' handling for transmit completions. Transmit
completion processing does not have a processing limit, so it always
runs to completion and never has more work to do when it returns.
Instead, the previous code was returning 'true' anytime there were
packets in the queue that weren't still in the process of being
transmitted. The effect was that the driver would continuously
reschedule a task to process TX completions in effect running at 100%
CPU polling the hardware until it finished transmitting all of the
packets in the ring. Now it will just wait for the next TX completion
interrupt.
- Restart packet transmission when the link becomes active.
- Fix the MSI-X queue interrupt handlers to restart packet transmission if
there are pending packets in the relevant software queue (IFQ or buf_ring)
after processing TX completions. This is the root cause for the OACTIVE
hangs as if the MSI-X queue handler drained all the pending packets from
the TX ring, nothing would ever restart it. As such, remove some
previously-added workarounds to reschedule a task to poll the TX ring
anytime OACTIVE was set.
Tested by: sbruno
Reviewed by: jfv
MFC after: 1 week
order to avoid otherwise harmless witness warnings when these are acquired
at the same time and due to both using MTX_NETWORK_LOCK as their type.
The right fix actually would be to use different, descriptive types for
these. However, the latter would require undesirable changes to the shared
code base. Another approach would be to just supply NULL as the type, which
was deemed as less desirable though as it would cause the unique but cryptic
name also to be used for the type and to diverge from the type used by other
network device drivers.
MFC after: 1 week
USERSPACE:
1. add support for devices with different number of rx and tx queues;
2. add better support for zero-copy operation, adding an extra field
to the netmap ring to indicate how many buffers we have already processed
but not yet released (with help from Eddie Kohler);
3. The two changes above unfortunately require an API change, so while
at it add a version field and some spares to the ioctl() argument
to help detect mismatches.
4. update the manual page for the two changes above;
5. update sample applications in tools/tools/netmap
KERNEL:
1. simplify the internal structures moving the global wait queues
to the 'struct netmap_adapter';
2. simplify the functions that map kring<->nic ring indexes
3. normalize device-specific code, helps mainteinance;
4. start exploring the impact of micro-optimizations (prefetch etc.)
in the ixgbe driver.
Use 'legacy' descriptors on the tx ring and prefetch slots gives
about 20% speedup at 900 MHz. Another 7-10% would come from removing
the explict calls to bus_dmamap* in the core (they are effectively
NOPs in this case, but it takes expensive load of the per-buffer
dma maps to figure out that they are all NULL.
Rx performance not investigated.
I am postponing the MFC so i can import a few more improvements
before merging.
