Add a "-x" option to chown(8)/chgrp(1) similar to the same option in
du(1), cp(1) etc, to prevent the crossing of mountpoints whilst using the
commands recursively.
PR: bin/130855
Submitted by: keramida
Make script(1) a little less broken.
Close the file descriptor to the TTY. There is no reason why the parent
process should keep track of the descriptor. This ensures that the
application inside properly drains the TTY during exit(2).
Reported by: alfred
It seems PCI_OUR_REG_[1-5] registers are not mapped on PCI
configuration space on Yukon Ultra(88E8056) such that accesses to
these registers were NOPs which in turn make msk(4) instable on
this controller. Use indirect access method to access
PCI_OUR_REG_[1-5] registers. This should fix a long standing
instability bug which prevented msk(4) working on Yukon Ultra.
Special thanks to koitsu who gave me remote access to his system.
PR: kern/114631, kern/116853
r204975:
Enable hardware fixes for BCM5704 B0 as recommended by data sheet.
r204978:
Set maximum read byte count to 2048 for PCI-X BCM5703/5704 devices.
Also disable relaxed ordering as recommended by data sheet for
PCI-X devices. For PCI-X BCM5704, set maximum outstanding split
transactions to 0 as indicated by data sheet.
For BCM5703 in PCI-X mode, DMA read watermark should be less than
or equal to maximum read byte count configuration. Enforce this
limitation in DMA read watermark configuration.
r204979:
Fix typo in r204975.
r204981:
Fix typo in r204978.
Remove taskqueue based interrupt handling. After r204541 msk(4)
does not generate excessive interrupts any more so we don't need
to have two copies of interrupt handler.
While I'm here remove two STAT_PUT_IDX register accesses in LE
status event handler. After r204539 msk(4) always sync status LEs
so there is no need to resort to reading STAT_PUT_IDX register to
know the end of status LE processing. Just trust status LE's
ownership bit.
Implement rudimentary interrupt moderation with programmable
countdown timer register. The timer resolution may vary among
controllers but the value would be represented by core clock
cycles. msk(4) will automatically computes number of required clock
cycles from given micro-seconds unit.
The default interrupt holdoff timer value is 100us which will
ensure less than 10k interrupts under load. The timer value can be
changed with dev.mskc.0.int_holdoff sysctl node.
Note, the interrupt moderation is shared resource on dual-port
controllers so you can't use separate interrupt moderation value
for each port. This means we can't stop interrupt moderation in
driver stop routine. Also have msk_tick() reclaim transmitted Tx
buffers as safety belt. With this change there is no need to check
missing Tx completion interrupt in watchdog handler, so remove it.
Honor ip.fw.one_pass when a packet comes out of a pipe without being delayed.
I forgot to handle this case when i did the mtag cleanup three months ago.
I am merging immediately because this bugfix is important for
people using RELENG_8.
PR: 145004
Fix the race between dotdot lookup and forced unmount, by using
msdosfs-specific variant of vn_vget_ino(), msdosfs_deget_dotdot().
As was done for UFS, relookup the dotdot denode after the call to
msdosfs_deget_dotdot(), because vnode lock is dropped and directory
might be moved.
MFC r204675:
When returning error from msdosfs_lookup(), make sure that *vpp is NULL.
Properly progress through the list of IPv6 addresses using in6_addr size.
Right now if a jail has multiple IPv6 addresses, it will print them
shifting only 4 bytes at a time. Example:
2001:4dd0:ff41::b23f:a9
2001:4dd0:ff41::b23f:aa
Becomes:
2001:4dd0:ff41::b23f:a9
ff41::b23f:a9:2001:4dd0
By casting to in6_addr, it uses the correct offsets.
Scrt1_c.o was accidentally compiled with -DGCRT (profiling), like gcrt1_c.o.
This problem is i386-specific, the other architectures are OK.
If you have problems with PIE executables such as samba and cups leaving
behind gmon files, rebuild them after installing this change.
PR: ports/143924
Disable TSO on BCM5755M controller until I understand better for
the issue. I still have no idea why TSO does not work on this
controller. davidch@ also confirmed there is no known TSO related
issues for this controller.
r204373:
Move TSO setup to new function bce_tso_setup(). Also remove VLAN
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
r204374:
Add TSO support on VLANs. bce(4) controllers require VLAN hardware
tagging to make TSO work on VLANs so explicitly disable TSO on VLAN
if VLAN hardware tagging is disabled.
r204368:
Allow disabling VLAN hardware tag stripping with software work
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
r204370:
Make sure to stop controller first before changing MTU. And if
interface is not running don't initialize controller.
While here remove unnecessary update of error variable.
r204371:
Make toggling TSO, VLAN hardware checksum offloading work. Also fix
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
r204372:
Prefer m_collapse(9) over m_defrag(9).
r204363:
Optimize inserting LE for TX checksum computation. Controller does
not require checksum LE configuration if checksum start and write
position is the same as before. So keep track last checksum start
and write position and insert new LE whenever the position is
changed. This reduces number of LEs used in TX path as well as
slightly enhance TX performance.
r204365:
Don't hardcod register offset to set PCIe max read request size.
The register offset is not valid on 88E8072 controller. Also don't
blindly increase max read request size to 4096, instead, use 2048
which seems to be more sane value and only change the value if the
hardware default size(512) was used on that register.
For PCIX controllers, use system defined constant rather than using
magic value.
While I'm here stop showing negotiated link width.
r204366:
Allocate single MSI message. msk(4) used to allocate 2 MSI messages
for controllers like 88E8053 which reports two MSI messages.
Because we don't get anything useful things with 2 MSI messages,
allocating 1 MSI message would be more sane approach.
While I'm here, enable MSI for dual-port controllers too. Because
status block is shared for dual-port controllers, I don't think
msk(4) will encounter problem for using MSI on dual-port
controllers.
r204367:
Remove trailing white spaces.
r204539:
Properly sync status LEs after processing.
r204540:
Make sure to enable flow-control only if established link is
full-duplex. Previously msk(4) used to allow flow-control on
1000baseT half-duplex media. Also GMAC pause is enabled if link
partner is capable of handling it.
While I'm here use IFM_OPTIONS instead of using IFM_GMASK to check
optional flags of link.
r204361:
Reuse the configured LE for VLAN if new LE was created for TSO.
Only old controllers need to create new LE for TSO. This change
makes TSO work over VLANs.
r204362:
Add TSO support on VLANs. Controller requires VLAN hardware tagging
to make TSO work over VLANs.
r204228:
Add TSO support on VLANs. Also make sure to update TSO capability
whenever jumbo frame is configured.
While I'm here remove unnecessary check of VLAN hardware checksum
offloading. vlan(4) already takes care of this.
r204230:
Remove Tx mbuf parsing code for VLAN in TSO path. Controller does
not support TSO over VLAN if VLAN hardware tagging is disabled so
there is no need to check VLAN here.
r204155:
Increase PCIe maximuim read request size to 2048. Because re(4) uses
Tx DMA burst size 2048, I beleive PCIe maximum read request size
also should match to the value of Tx DMA burst size. With this
change I can get more than 800Mbps for TCP bulk transfers.
Previously I was not able to get more than 700Mbps. If I enable TSO
it now shows 927Mbps.
r204219:
Add TSO on VLANs. Because re(4) has a TSO limitation for jumbo
frame, make sure to update VLAN capabilities whenever jumbo frame
is configured.
While I'm here rearrange interface capabilities configuration. The
controller requires VLAN hardware tagging to make TSO work on VLANs
so explicitly check this requirement.
r204151:
Add TSO support on VLAN. Controller requires VLAN hardware tagging
to make TSO work on VLAN. So if VLAN hardware tagging is disabled
explicitly clear TSO on VLAN. While I'm here remove duplicated
VLAN_CAPABILITIES call.
r204223:
Remove Tx mbuf parsing code for VLAN in TSO path. Controller does
not support TSO over VLAN if VLAN hardware tagging is disabled so
there is no need to check VLAN here.
While I'm here make sure to pullup IP/TCP headers in the first
buffer.
Use an unique directory name instead of hardcoded /tmp/.diskless.
A malicious user could create a file named /tmp/.diskless and cause
the script to misbehave.
PR: conf/141258
done in CURRENT over the last 4 months.
HEAD and RELENG_8 are almost in sync now for ipfw, dummynet
the pfil hooks and related components.
Among the most noticeable changes:
- r200855 more efficient lookup of skipto rules, and remove O(N)
blocks from critical sections in the kernel;
- r204591 large restructuring of the dummynet module, with support
for multiple scheduling algorithms (4 available so far)
See the original commit logs for details.
Changes in the kernel/userland ABI should be harmless because the
kernel is able to understand previous requests from RELENG_8 and
RELENG_7. For this reason, this changeset would be applicable
to RELENG_7 as well, but i am not sure if it is worthwhile.
- Fix a bug when adding an interface with an invalid MTU sets the
bridge's MTU if it is the firstly-added one while the addition
itself fails.
- Allow SIOCSIFMTU only when all members have the same MTU.
- Remove IFT_GIF check when defining the brige MTU by the
firstly-added interface's one. The MTU of the gif interface
has to be the same as the bridge's one.
The Australian Antartic Division:
- Macquarie Island will stay on UTC+11 for winter and not switch back from DST.
- Casey station reverted to its normal time of UTC+8 on 5 March 2010.
- Davis station will revert to its normal time of UTC+7 at 10 March 2010
- Mawson station stays on UTC+5.
Syria will start DST on Thursday 1 April 2010 at midnight.
Correct Samao DST start date (26 Sep vs 24 Oct)
Fix a long standing regression of readdir(3) in fdescfs(5) introduced
in r1.48. We were stopping at the first null pointer when multiple file
descriptors were opened and one in the middle was closed. This restores
traditional behaviour of fdescfs.
Tidy up callout for select(2) and read timeout.
- Add a missing callout_drain(9) before the descriptor deallocation.[1]
- Prefer callout_init_mtx(9) over callout_init(9) and let the callout
subsystem handle the mutex for callout function.
PR: kern/144453
Submitted by: Alexander Sack (asack at niksun dot com)[1]
