controller. Some testing has already been done, but its still greenish.
RAID's has to be setup via the BIOS on the SuperTrak, but all RAID
types are supported by the driver. The SuperTrak rebuilds failed arrays
on the fly and supports spare disks etc etc...
Add "device pst" to your config file to use.
As usual bugsreports, suggestions etc are welcome...
Development sponsored by: Advanis
Hardware donated by: Promise Inc.
debugging levels to off by default. Now that debug levels can be
tweaked by sysctl we don't need to go through hoops to get the
different usb parts to produce debug data.
frees it again. The idea was to perform M_WAITOK allocations in a
process context to reduce the risk of later interrupt-context
M_NOWAIT allocations failing, but in fact this code can be called
from contexts where it is not desirable to sleep (e.g. if_start
routines), so it causes lots of witness "could sleep" warnings.
is that some cards built around fm801 chip have the same device ID, only
have radio tuner onboard, but no sound capabilities. Therefore, with such
card inserted and `device pcm' in kernel the user has a big problem, as
the fm801 driver effectively hangs the machine when trying to initialise
nonexistent ac97 codecs (it does 500 retries with 1 second interval!).
It would be better if MediaForte's engeneers were smart enough to put
different device ID into such cards, but it isn't an option.
MFC after: 2 weeks
problems with the firmware and will result in a) poor performance and
b) the inability to associate certain types of cards (most notibly
cisco).
Idea obtained from OpenBSD, but I implemented it by clearing the
IFF_PROMISC flag rather than the refusing to honor it downstream.
1.131 is slightly broken, and I would commit the fix to that here, but it
has been reported that any deviation from the original code is causing
problems with some 82557 chips, causing them to lock hard.
Until those issues have been figured out, going back to the original
code is the best plan.
Frustrated: Silby
o Rename the insanely long PCIC bridge ids.
o Add my copyright to pccbb.c
o Add support for the TI-1510, TI-1520 and TI-4510 series of upcoming
bridges.
o Init MFUNC if it is zero and the TI part has a MFUNC register
at offset 0x8c (1030, 1130 and 1131 don't have anything there, the
1250,1251,1251B and 1450 have a different thing there. The rest
have it. TI is likely to only do MFUNC from now on. The IRQMUX
in the 1250 series of chips needs no tweaks.
o Adjust to new exca interface.
o Add comments about TI chips that I learned in talking to an
engineer at TI.
o Add register definitions for MFUNC.
o Create CB_TI125X chipset type.
o Protect .h against multiple includes.
o eliminate the pointers to the read/write routines. The
bus_space_read routines can cope since we have the offset
field.
o Print a warning if the requested map address is > 16M and
your chipset doesn't support the extended ExCA registers.
of the Netgear GA302-T. I changed the symbolic names in the
submitter's patch to reflect the part number of the chip instead
of the board.
PR: kern/38988
Submitted by: Brad Chapman <chapmanb@arches.uga.edu>
MFC after: 2 days
Through the PITA of endiannness, clock has to be MHz freq << 8.
Don't trust NVRAM on SBus cards.
Set a default initiator ID sensibly.
SBus/ISP now working, what with the change to sbus.c earlier today.
flags include INTR_MPSAFE. Put the flags in a common place so that
both isp_sbus && isp_pci DTRT.
In isp_mbxdma setup, drop any locks prior to calling things like
bus_dmatag_create. This gets rid of these obnoxious WITNESS messages
about 'sleeping with locks held' blah blah blah blah blah.
