I missed. Since I did no rearrange any softcs, casting the result of
device_get_softc() to (struct ifnet **) and derefrencing it yeilds a
pointer to the ifp. This makes at least vr(4) nics work.
NetBSD got activated. NetBSD has an additional change in
their mii.c rev 1.26 which got missed with that merger:
: When probing for a PHY, look at the EXTSTAT bit in the BMSR, as well,
: not just the media mask. This prevents PHYs/TBIs that only support
: Gigabit media from slipping through the cracks.
With this GE only ones like from the SK-9844 are detected again.
PR: i386/63313, i386/71733, kern/73725
Tested by: matt baker <matt at sevenone dot com>, Jin Guojun <jin at george dot lbl dot gov>
Approved by: rwatson (mentor)
Obtained from: NetBSD mii.c rev 1.26
MFC after: 1 week
I have from Broadcom does not give much information on these devices,
so the Broadcom Linux driver was used for clues to what these chips
support. It turns out they are similar to the 5705 with the 5751
being the PCI-Express version and needing special work-arounds and
settings.
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
a more complete subsystem, and removes the knowlege of how things are
implemented from the drivers. Include locking around filter ops, so a
module like aio will know when not to be unloaded if there are outstanding
knotes using it's filter ops.
Currently, it uses the MTX_DUPOK even though it is not always safe to
aquire duplicate locks. Witness currently doesn't support the ability
to discover if a dup lock is ok (in some cases).
Reviewed by: green, rwatson (both earlier versions)
properly. This causes the autonegotiation to e.g. never establish a
100baseTX full-duplex link. The solution to this problem is to manually
write the capabilities from the BMSR to the ANAR every time a media
change occurs, even when already in autonegotiation mode.
The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the
NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which
will set the ANAR according to the BMSR) even when the PHY alread is in
autonegotiation mode. However, while doing the same on FreeBSD (which
involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use
mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia()
causes this driver to no longer work properly in the other modes.
Another drawback of that approach is that this will also force writing
the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which
are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is
known to be used together with 3 different PHYs while only the DP83840A
require this workaround).
So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in
nsphy_service() unconditionally when hanging off of a hme(4) and serving
a media change
This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
o Extend the if_data structure with an ifi_link_state field and
provide the corresponding defines for the valid states.
o The mii_linkchg() callback updates the ifi_link_state field
and calls rt_ifmsg() to notify listeners on the routing socket
in addition to the kqueue KNOTE.
o If vlans are configured on a physical interface notify and update
all vlan pseudo devices as well with the vlan_link_state() callback.
No objections by: sam, wpaul, ru, bms
Brucification by: bde
the falling edge of a media state change.
This is in preparation for media state change notification to the
routing socket.
No objections by: sam, wpaul, ru, bms
Brucification by: bde
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Tested at 100Mbit only, using Asus P4P800 onboard 3C940.
The -stable version of this patch I have in use for ~2 weeks now, and works
just fine for me.
Based on: Nathan L. Binkert's patch for OpenBSD
Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com>
MFC after: 2 weeks
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
These are 10/100 only NICs found on the IBM Thinkpad R40E and
G40. These seem to be based on the BCM5705 MAC but with a PHY
that doesn't support 1000Mbps modes.
Submitted by: Igor Sviridov <sia@nest.org>
- 5705 doesn't support jumbo frames
- Statistics must be read from registers
- RX return ring must be capped at 512 entries
- Omit initialization of certain device blocks
- Acknowledge link change interrupts by setting the 'link changed'
bit in the status register (used to have no effect)
- Remember to toggle the MI completion bit too
- Set the mbuf low watermark differently (on-chip memory buffers,
not BSD mbufs)
- Don't enable Ethernet@WireSpeed feature for certain 5705 chip revs
- Add additional PCI IDs for 5705 and 5782 parts
- Add a forgotten 5704 PCI ID
Most changes ripped kicking and screaming from the Broadcom linux driver.
Thanks to Paul Saab for sanity testing. (My lack of sanity has been
confirmed.)
patch workarounds for each phy revision.
Obtained from: NetBSD & Broadcom Linux driver
- Disable AUTOPOLL when accessing the PHY as it may cause PCI errors.
Obtained from: NetBSD
- Check the UPDATED bit in the status block so the driver knows
that the status block as indeed changed since the last access.
Broadcom documentation states drivers should unset the UPDATED/CHANGED
bits after reading them.
- When changing media types, first loop the phy then set the media.
Broadcom documentation and Linux drivers do this and I observed
much better handling of link after this change.
- Broadcom documentation states that for 1000BaseT operation,
autonegotiation must be enabled. Fix hard coding of media so that
the driver only advertises 1000BaseT as the supported media type
and enable autonegotition.
- Only set Master/Slave on the 5701.
Obtained from Broadcom Linux driver.
cards to test; however the submitter reports that this patch works
with the on-board interface on the IBM x235 server.
Submitted by: Jung-uk Kim <jkim@niksun.com>
MFC after: 1 month
when this is needed. Work around bogus second PHY in the DFE-580 card
via a change in the if_ste.c driver.
Suggested by: jdp
Reviewed by: jdp
MFC after: 3 days
