* Fix a bug where caches were flushed on non-C3 transitions.
* Be sure a working flush cache instruction is present before using it.
* Disable C3 completely if it isn't present.
may want to shut down here but the chance of BIOS vendors getting this
wrong is high. They're only supposed to announce this when all batteries
hit their critical level but past experience indicates we should be
conservative about this for now.
with acpi but the timer runs twice as fast. Note that the main problem
(system doesn't work properly with acpi disabled) should be fixed separately.
Changes:
* Add a quirk to disable the timer
* Merge the P5A and P5A-B quirks since they appear to be based on the
same ASL.
PR: i386/72450
Tested by: Kevin Oberman <oberman es.net>
MFC after: 3 days
allocate unallocated memory resources from the top 32MB of the address
space rather than the top 2GB. While the latter works on some
chipsets, it fails badly on others. 32MB is more conservative and
matches what cheap harware from this era is hardwired to pass.
table. acpidump(8) concatenates the body of the DSDT and SSDTs so an
edited ASL will contain all the necessary information. We can't use a
completely empty table since ACPI-CA reports this as a problem.
MFC after: 3 days
would turn off all fans when initializing a zone. However, the HP Omnibook
500 generates a notify saying the zone needs to be re-evaluated whenever
its fan is switched on or off. This produced an infinite loop. Also, note
that running _SCP can generate the same notify.
Since we need to make sure old fan references are turned off when getting
new ones, run acpi_tz_monitor() first. This will turn off any unneeded
fans. Then, check for new settings. After that, run acpi_tz_monitor()
again to turn on/off any fans referenced by the new settings.
Tested by: brooks
returned and then infer the state from calls to _ON/_OFF. This works
around a problem in systems that don't correctly report the state (i.e.
the HP Omnibook 500 reports "on" for its fan always after it has been
turned on once).
unless ACPI_DEBUG is defined. Users don't typically care about errant
breakpoint instructions. The HP Pavilion 7915 has this in its PCI0
_INI method for rev 0x6040000 of the RSDT.
should only affect current resources, it seems best to wait until all
configuration is done before disabling it. If this fixes any problems, it
is a MT5 candidate.
hold its own values, pass them up to the parent (acpi0) and merge/uniq them
on the way. After the namespace evaluation, acpi will reserve these
resources and manage them via rman before bus_generic_probe() and
bus_generic_attach(). This is necessary because some systems specify
conflicting resources in separate sysresource objects. It's also cleaner
in that the interface between sysresource and acpi is now merely the parent's
resource list. This code handles the following cases:
1. Unique resource: add it to the parent via bus_set_resource().
2. New wholly contained in old: discard new.
3. New tail overlaps old head: grow old head downward.
AND/OR
4. New head overlaps old tail: grow old tail upward.
Tested by: Pawel Worach <sajd_at_telia.com>
Tested by: Radek Kozlowski <radek_at_raadradd.com>
MFC after: 5 days
systems that have overlapping regions specified in their sysresource
objects. This patch fixes ATA DMA and acpi_timer allocation for such
sysctems. It should eventually be moved to resource_list_add() if it is
a valid generalized approach. The minimal approach for 5.3 is:
"Loop through all current resources to see if the new one overlaps
any existing ones. If so, the old one always takes precedence and
the new one is adjusted (or rejected). We check for three cases:
1. Tail of new resource overlaps head of old resource: truncate the
new resource so it is contiguous with the start of the old.
2. New resource wholly contained within the old resource: error.
3. Head of new resource overlaps tail of old resource: truncate the
new resource so it is contiguous, following the old."
Tested by: Radek Kozlowski <radek_at_raadradd.com>
Discussed with: imp
MFC after: 4 days
callers. These ioctls attempted to enable and disable the ACPI
interpreter at runtime. In practice, it is not possible to boot with
ACPI and then disable it on many systems and trying to do so can cause
crashes, interrupt storms, etc. Binary compatibility with userland is
retained.
MFC after: 2 days
also generates a notify. Since we held the lock over this call, the
notify never got to run and the battery status read never returned.
Document this also.
Tested by: Maxim Maximov <mcsi_at_mcsi.pp.ru>
Approved by: re (scottl)
* Remove the interrupt wrapper that locked Giant and call the handler
directly. Mark the handler as MPSAFE.
* Don't attempt to detect if a handler is installed. Leave that to the
bus_alloc_resource() function.
* Serialize operations in acpi_video_bind_outputs(), acpi_video_detach(),
acpi_video_notify_handler(), acpi_video_power_profile(), and the sysctls.
The main goal is to protect the shared device list and prevent conflicting
settings.
* Add assertions that the sx lock is held in the leaf functions.
* Restructure the event handling path. acpi_tz_thread() now calls
acpi_tz_timeout() any time an event occurs. acpi_tz_timeout() checks
the flags and calls acpi_tz_power_profile(), acpi_tz_establish(), and
acpi_tz_monitor() as appropriate. Notifies only do a wakeup and let
acpi_tz_thread() do the actual work. This path is cleaner and allows
locking since the call path is now always a D.A.G.
* Add the acpi_tz_signal() function to set flags and wake the thread.
* Remove the tz_tmp_updating flag since calls are serialized by
acpi_tz_thread().
* Remove Giant locking.
* Serialize acpi_pwr_switch_consumer() and acpi_pwr_wake_enable().
* Make acpi_pwr_switch_consumer() have a single exit point.
* Add assertions to the leaf functions they call.
* Fix a memory leak in acpi_pwr_deregister_consumer(). However, it is
currently ifdefed out so this code was unused.
* Serialize access to acpi_pci_link_config(), acpi_pci_find_prt(),
acpi_pci_link_route(), and acpi_pci_link_resume().
* Add lock assertions to all functions called by them.
* Serialize notifying the user in acpi_lid_notify_status_changed(). This
way multiple lid events occur in order.
* Add an initialization pass to get the lid status at boot-time. This
pass does not notify any apps but gets the initial status.
* Use the common serialization macros instead of rolling our own.
* Increase the coverage of the lock in EcSpaceHandler() to cover the entire
loop to avoid dropping the lock when reading more than one byte.
* Serialize ops in acpi_cmbat_notify_handler(), acpi_cmbat_ioctl(),
acpi_cmbat_init_battery(), and acpi_cmbat_get_battinfo().
* Get the softc directly in acpi_cmbat_get_total_battinfo() rather than
build an array of them.
* Don't queue a _BIF query after receiving a notify. Since we clear the
timespec, a _BIF query will be done in the context of the next caller.
* Add asserts to leaf functions that operate on shared data.
* Remove the bst/bif updating flags now that we hold the lock over the
full query.
* Explain various comments in more detail.
* Serialize acpi_battery_get_battdesc(), acpi_battery_register(), and
acpi_battery_remove().
* Assert that the sx lock is held in acpi_batteries_init().
* Remove check for device_get_softc() returning NULL.
* Serialize notification of acline changes in acpi_acad_get_status().
* Remove the initializing flag. With the locking, we don't need to
push off requests for the acline before initialization is done.
* Don't check device_get_softc(), it can't return NULL.
* Serialize calls to acpi_alloc_resource(), acpi_release_resource(),
acpi_Enable(), acpi_Disable(), and acpi_debug_sysctl().
* Acquire the ACPI mutex in acpi_register_ioctl(), acpi_deregister_ioctl(),
and acpiioctl().
* Acquire the mutex while disabling subsequent requests to enter a
sleep state in acpi_SetSleepState().
* Be sure to re-enable sleep requests and don't run resume methods when
the current request fails.
* Don't check if sleep requests are disabled in the ACPIIO_SETSLPSTATE
ioctl. acpi_SetSleepState() does this for us.
* Remove the acquisition of Giant from the struct cdevsw.
* Remove the ACPI_USE_THREADS option.
* Add and comment our locking primitives. The mutex primitives use a
a static mutex and the serialization ones use a static sx lock. A global
acpi_mutex is used for access to global resources (i.e., writes to the
SMI_CMD register.)
* Remove 4.x compat defines.
there is no irq link. Since we now use the stored copy of PRT, not the
one that used to be passed into acpi_pcib_route_interrupt(), we need it in
the list. [1]
Fix a bug in acpi_pci_find_prt() where we weren't checking the bus, thus
choosing the wrong PRT entry to use for routing the link. Also, add a
printf for the case where the PRT entry is not found as this should not
happen.
Tested by: marcel [1]
incomplete in that the PRT routing was not aware of link programming.
Fix this by doing all routing through the link devices. The new algorithm
for setting up links is:
1. Read _CRS to get current setting. If invalid (not in _PRS), then set
to 0.
2. Attempt to call _DIS on the link. If successful, mark the link as not
routed. Otherwise, assume it still is.
Then when a routing request occurs:
3. Update weights for all IRQs
4. Attempt to route the initial IRQ if valid
5. If that fails, walk through the sorted list, attempting to route IRQs.
6. Configure the trigger/polarity based on _PRS.
Other changes:
* Add acpi_pci_find_prt() to look up the PRT entry for a given device and
acpi_pci_link_route() to select/route the best IRQ for it.
* Remove duplicated code in acpi_pcib_route_interrupt() that picked the
first IRQ from _PRS.
* Remove unneeded arguments from acpi_pcib_resume() and friends.
* Ignore _STA on link devices but report if it seems strange.
* Add a prt_source handle to the PRT structure since the ACPI struct
ACPI_PCI_ROUTING_TABLE uses a fixed-size entry for it. We'll need to
dynamically size this object if we want to use it the same way ACPI-CA
does. Null-terminate the source.
Tested by: Luo Hong <luohong99_at_mails.tsinghua.edu.cn>,
Jeffrey Katcher <jmkatcher_at_yahoo.com>
Info from: jhb, Len Brown (Intel)
message if they are incorrect. Also, remove the hack of allowing the
initial irq setting to not be in _PRS. As before, the old behavior can be
regained by defining ACPI_OLD_PCI_LINK.
following behavior:
* Link devices return invalid status (_STA) values. The results are very
unreliable -- sometimes never present. Just ignore the status and pick
the best configuration from _PRS.
* Link devices return invalid current settings (_CRS). Even after setting
the link value, many systems still return a different setting for _CRS.
When setting an IRQ, don't bother to check _CRS to see if we succeeded.
Note that we still check _CRS before routing and this should be addressed
as well.
Since this is a sensitive area, leave the old behavior accessible via
uncommenting the define for ACPI_OLD_PCI_LINK at the top of the file. Once
this has been thoroughly tested, this option and the code it covers will
be removed.
Thanks to Len Brown at Intel for informing us of these issues as he worked
around them in Linux.
ACPI_DEBUG. This upset the ordering that acpi_probe_order() was meant to
provide, causing devices to attach before the sysresource object. This
debugging feature has been unnecessary for a while so just remove it.
Testing by: marcel
FOREACH_SAFE. Remove bad cast of retp and instead use an additional
arg to pass back the number of valid outputs. Use the package convenience
functions for parsing packages.
left around after the PCI probe, acpi_video stopped attaching because while
it was an acpi child device, it really is a PCI device. Fix this by making
it a PCI child.
* Remove non-handle ivars accesses since child busses only implement
acpi_get_handle().
* Access the acpi softc directly through the devclass instead of through
the implied parent.
* Clean up a potential panic on unload by freeing the sysctl context before
storing NULL in the OID.
Found by: marks
allows a bus to re-enumerate its child handles and optionally replace
them with new children, arranged to the bus's liking. (The current device
space is flat with all devices immediately under acpi0). Add comments
for each interface.
when the battery is fully charged. That breaks some of the arithmetic in
calculating the remaining capacity (ends up with more than 100%).
This commit makes sure the max is 100.
Approved by: njl
needed so that sysresource objects are created first to reserve all regions,
then other devices can allocate from them. Otherwise, acpi_timer (the only
ACPI device with an identify routine), would allocate its resources from
the nexus, causing the later sysresource reserve to fail.
Debugging by: Taku YAMAMOTO, Andrea Campi
this more accurately reflects what the underlying hardware of most
acpi machines that don't have children pci busses.
We still need a better way to get this information from acpi/hardware.
header pointer and then casting it to the ecdt pointer. This fixes the
-O2 build. I'm unsure what changed recently to reveal this error since
this code has been unchanged for months.
instead of a mutex so we do not unblock it in msleep(). If we do this,
another event could occur, resetting the status register since reads
reset it. While I'm here, remove the backoff approach. Instead, sleep
in 10 ms chunks for up to the configured timeout using either DELAY (if
we aren't booted yet) or tsleep.
Help from: dillon
Tested by: Andrew Thompson andy AT fud.org.nz
Unify the code to disable GPEs with the enable code. Shutdown is handled
the same way. ACPI now does all wake/sleep prep for child devices so
now they no longer need to call external functions in the suspend/resume
path. Add the flags to non-ACPI busses (i.e., pci).
This brings us into line with the standard, which requires power resources
be enabled when wake is enabled for a given device. Move the dereferencing
code into its own function, +acpi_pwr_dereference_resource().
code that was never really used. Print a message when disabling ACPI via
a quirk. Allow the user to override the blacklist decision by setting
hint.acpi.0.disabled="0". Add missing AcpiTerminate() calls; they are
needed to clean up if bailing out after AcpiInitializeSubsystem().
namespace. This is to allow decoupling of attachments from ACPI where they
need some functionality when ACPI is present but do not want to require ACPI
to always be loaded.
starting value. This is more pedantically correct (since the handle
isn't always identical to the start of the resource) and also doesn't
access the innards of struct resource direct (which I forbid in my
tree). We need to do this for all resource types, not just ioport.
Reviewed by: njl
are currently all bad BIOS revisions that will never be able to support
ACPI. They were derived by examining which BIOS's are blacklisted by other
operating systems. Other types of quirks will be possible here as well.
smp_rendezvous() to ensure we run on the BSP. This reverts rev 1.128.
Add a comment indicating that MI code should be the one that runs all
shutdown functions on the BSP with the APs halted. This should work
around problems in power off while waiting for the MI code to be improved.
actually used. For most ACPI devices this means deferring the call
until bus_alloc_resource().
- Add a function acpi_config_intr() to call BUS_CONFIG_INTR() for an
ACPI IRQ resource using the trigger mode and polarity information
stored in the ACPI resource object.
- Add a function acpi_lookup_irq_resource() to lookup the ACPI IRQ
resource that corresponds to a specified rid and new-bus resource.
- Have the ACPI PCI bridge driver call BUS_CONFIG_INTR() on interrupts
that it routes through link devices.
- Remove needactivate variable from acpi_alloc_resource() by changing the
function not modify the flags variable but just mask off RF_ACTIVE when
calling rman_reserve_resource().
Reviewed by: njl (1, an earlier version)
device associated with any PCI devices that are enumerated in the ACPI
tree when adding children to an ACPI PCI bus and remove the duplicate
ACPI-only device_t and replace the device_t associated with the handle with
the ACPI and PCI aware device_t.
allocation was passed up to nexus. Now, we probe sysresource objects and
manage the resources they describe in a local rman pool. This helps
devices which attach/detach varying resources (like the _CST object) and
module loads/unloads. The allocation/release routines now check to see if
the resource is described in a child sysresource object and if so,
allocate from the local rman. Sysresource objects add their resources to
the pool and reserve them upon boot. This means sysresources need to be
probed before other ACPI devices.
Changes include:
* Add ordering to the child device probe. The current order is: system
resource objects, embedded controllers, then everything else.
* Make acpi_MatchHid take a handle instead of a device_t arg.
* Replace acpi_{get,set}_resource with the generic equivalents.
which doesn't support ACPI power states. Return AE_NOT_FOUND for these
cases and don't print the warning message. Also, print the name of the
handle instead of device when unable to switch states. The device is often
not attached at this point and so its name is NULL, which doesn't help
debugging.
"stray irq 9" messages on my Thinkpad. It may also help with general
reboot consistency although the recent hang on reboot was solved by
acpi_cpu.c rev 1.39.
after. Unify the paths for all Cx states. Remove cpu_idle_busy and
instead do the little profiling we need before re-enabling interrupts.
Use 1 quantum as estimate for C1 sleep duration since the timer interrupt
is the main reason we wake.
While here, change the cx_history sysctl to cx_usage and report statistics
for which idle states were used in terms of percent. This seems more
intuitive than counters. Remove the cx_stats structure since it's no
longer used. Update the man page.
Change various types which do not need explicit size.
correct. Instead, check it against the possible settings (_PRS) when
the link is probed. This is important when using APIC mode but link
devices still have PIC mode settings. This is also what Linux does.
Additional prodding by: Len Brown len dot brown at intel dot com
based on the destination sleep state. Add a method to restore the old
state on resume. This is needed for the case of suspending to a very low
state disabling a GPE (i.e. S4), resuming, and then suspending to a higher
state (i.e. S3). This case should now keep the proper GPEs enabled.
device can wake the system. For example:
dev.root0.nexus0.acpi0.acpi_lid0.wake: 1
dev.root0.nexus0.acpi0.acpi_button0.wake: 1
dev.root0.nexus0.acpi0.pcib0.wake: 0
dev.root0.nexus0.acpi0.sio0.wake: 0
acpi_wake_init:
Evaluate _PRW and set the GPE type
acpi_wake_set_enable:
Enable or disable a device's GPE.
acpi_wake_sleep_prep:
Perform any last-minute changes to the device to prepare it for
entering the given sleep state.
Also, walk the entire namespace when transitioning to a sleep state,
disabling any GPEs which aren't appropriate for the given state. Transition
acpi_lid and acpi_button to the new API.
This clears the way for non-ACPI-aware devices to wake the system (i.e.
modems) and fixes a problem where systems power up after shutdown when a
GPE is triggered.
* Add calls to AcpiSetGpeType. We use wake/run as the type for lid and
button switches since wake-only causes Thinkpads to immediately wake on
the second suspend. Note that with wake/run, some systems return both
wake and device-specific notifies so we don't register for system notifies
for lid and button switches.
* Remove the hw.acpi.osi_method tunable since it is not needed.
* Always print unknown notifies for all types.
* Add more cleanup for the EC if it fails to attach.
* Use the GPE handle now that we parse it. This allows GPEs to be defined
in AML GPE blocks.
* Always use ACPI_NOT_ISR since it's ok to acquire a mutex in our thread
which processes queued requests.
return value for BUS_READ_IVAR and thus don't generate the proper NULL
in cases where a device (i.e. on PCI) does not have a handle.
Found by: peadar, tjr
the swizzle method for routing PCI interrupts across the bridge. This
fixes problems with motherboards (typically laptops) whose BIOS doesn't
provide a PRT for the AGP bridge even though there is a device entry for
the bridge in the ACPI namespace.
Tested by: Kenneth Culver culverk at sweetdreamsracing dot biz
devices it cannot attach to. This gets rid of extraneous but harmless
device_probe_and_attach() errors. While I'm here, make the device
description more useful. The !acpi case for cpu is handled by legacy0.
individual asm versions. The global lock is shared between the BIOS and
OS and thus cannot use our mutexes. It is defined in section 5.2.9.1 of
the ACPI specification.
Reviewed by: marcel, bde, jhb
1) In pci.c, we need to check the child device's state, not the parent
device's state.
2) In acpi_pci.c, we have to run the power state change after the acpi
method when the old_state is > new state, not the other way around.
Submitted by: Dmitry Remesov
PR: 65694
added an arbitrary delay to our readings, causing us to use the ACPI-safe
read method when not necessary. Submitted by: bde
Old:
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
New:
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
Also, reduce unnecesary overhead in ACPI-fast by remove the barrier for
reads. The timer in the ACPI-fast case is known to increase monotonically
so there is no need to serialize access to it.
gadgets (hotkeys, lcd, ...) on Asus laptops. I aim to closely track the
acpi4asus project which implements these features in the Linux kernel.
If this breaks your laptop, please let me know how it does it :-)
Approved by: njl (mentor)
workaround was for hardware where the clock was not latched, not for
hardware that was too slow. Also, make variable names more specific for ddb
printing.
what the ACPI-safe workaround is intended to fix. Requested by phk.
Set the bushandle and tag when attaching the timer, don't do it each time
in read_counter(). Pointed out by bde.
Move test_counter() to the end. Staticize acpi_timer_reg.
supported. Symptoms of this bug included unnecessary use of ACPI-safe
and a dmesg that has deltas of about 2^24:
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 16777210, width = 16777208
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
To fix this:
* Use a 32 bit timecounter mask when the timer is 32 bits.
* In test_counter(), use the acpi_TimerDelta function which handles 24/32
bit timers and wraparound.
Miscellaneous fixes:
* Use C99 initializers for timecounter struct.
* Use u_int and uint32_t where appropriate instead of unsigned.
* Remove whitespace-only lines
* Remove the old PIIX4 PCI workaround. The timecounter testing code has
been in use for long enough to prove it's functional.
globally available. acpi_TimerDelta() subtracts two readings from the
ACPI PM timer and returns the difference. It properly distinguishes between
24-bit and 32-bit timers and handles wraparound.
a NULL crsbuf pointer. This shouldn't happen if it returns AE_OK. We'll
figure out why this is happening later.
Submitted by: Bruno Ducrot <ducrot@poupinou.org>
o Save and restore bars for suspend/resume as well as for D3->D0
transitions.
o preallocate resources that the PCI devices use to avoid resource
conflicts
o lazy allocation of resources not allocated by the BIOS.
o set unattached drivers to state D3. Set power state to D0
before probe/attach. Right now there's two special cases
for this (display and memory devices) that need work in other
areas of the tree.
Please report any bugs to me.
Reference objects changed from ACPI_TYPE_ANY to ACPI_TYPE_LOCAL_REFERENCE
in Oct. 2002, this may help systems where switching the cooler on failed.
We support both types for now until this sorts out.
some machines to enable wake events for more devices although I haven't
seen a system yet that uses this form. Also, introduce acpi_GetReference()
which retrieves an object reference from various types.
are enumerated in the ACPI device tree. In addition to the normal PCI
powerstate functionality, the ACPI _PSx methods are executed and ACPI
PowerResources are switched on and off via the acpi_pwr_switch_consumer()
function.
Glanced at by: imp, njl
