instead, just dec/inc in the ctor/dtor. For now, increment/decrement
in two's, since we're now performing the operation once per pair,
not once per pipe. Not really any measurable performance change
in my micro-benchmarks, but doing less work is good, especially when
it comes to atomic operations.
Suggested by: alc
it is still above the critical temperature on the next poll cycle. This
is a 10 second advance notice by default. Document the private
(non-standard) notify we will be using with devd(8).
changes to jointly allocated pipe pairs. Replace these checks
with pipe_present checks. This avoids a NULL pointer dereference
when a pipe is half-closed.
Submitted by: Peter Edwards <peter.edwards@openet-telecom.com>
used for the ICMP reply source in reponse to packets which are not
directly addressed to us. By default continue with with normal
source selection.
Reviewed by: bms
1. Root from inside a jail was able to unmount any file system
(except /).
2. Unprivileged root was able to unmount file systems mounted by
privileged root (execpt /).
3. User from inside a jail was able to mount file system when
sysctl vfs.usermount was set to 1.
4. User was able to mount file system when vfs.usermount was set to 1
(that's ok) and unmount it even if vfs.usermount was equal to 0
(that's not correct).
Possibility from point 1 was reported by: Dariusz Kowalski <darek@76.pl>
Only a part of this fix will be MFC'ed (if approved).
PR: kern/60149
Reviewed by: rwatson
Approved by: scottl (mentor)
MFC after: 3 days
the system. Also, decrease the poll interval to 10 seconds from 30
seconds. This is needed because some systems will report an invalid high
temperature for one poll cycle. It is suspected this is due to the
embedded controller timing out. A typical value is 138C for one cycle on a
system that is otherwise 65C. This prevents the system from prematurely
shutting down after one invalid reading. It will still shut down after 30
seconds of high temperature, which is the same as previous default
behavior.
Tested by: Scott Lambert <lambert AT lambertfam.org>
is for an 802.11 device or not. At least one driver I have does not
support the OID_802_11_NETWORK_TYPES_SUPPORTED OID.
Also, for now, don't do anything special in the ndis_suspend() method.
I originally wanted to shut down the NIC but leave the IFF_UP flag alone
since technically the interface is meant to remain up, but an interrupt
may be delivered to the ISR on suspend, and if this happens while the
NIC is halted, we will crash, since none of the miniport driver methods
will function.
This needs to be dealt with properly later, but for now this prevents
a panic, and the resume method properly re-inits the NIC.
the thread that calls pmap_pte_quick() and by virtue of the page queues
lock being held, we can manage PADDR1/PMAP1 as a CPU private mapping.
The most common effect of this change is to reduce the overhead of the page
daemon on multiprocessors.
In collaboration with: tegge
packet along with data, instead of in their own packet. When serving files
of size (packetsize - headersize) or smaller, this will result in one less
packet crossing the network. Quick testing with thttpd and http_load has
shown a noticeable performance improvement in this case (350 vs 330 fetches
per second.)
Included in this commit are two support routines, iov_to_uio, and m_uiotombuf;
these routines are used by sendfile to construct the header mbuf chain that
will be linked to the rest of the data in the socket buffer.
sense with sched_4bsd as it does with sched_ule.
- Use P_NOLOAD instead of the absence of td->td_ithd to determine whether or
not a thread should be accounted for in sched_tdcnt.
when uma_reclaim() was called. This was introduced when the zone
working-set algorithm was removed in favor of using the per cpu caches
as the working set.
would allocate two 'struct pipe's from the pipe zone, and malloc a
mutex.
- Create a new "struct pipepair" object holding the two 'struct
pipe' instances, struct mutex, and struct label reference. Pipe
structures now have a back-pointer to the pipe pair, and a
'pipe_present' flag to indicate whether the half has been
closed.
- Perform mutex init/destroy in zone init/destroy, avoiding
reallocating the mutex for each pipe. Perform most pipe structure
setup in zone constructor.
- VM memory mappings for pageable buffers are still done outside of
the UMA zone.
- Change MAC API to speak 'struct pipepair' instead of 'struct pipe',
update many policies. MAC labels are also handled outside of the
UMA zone for now. Label-only policy modules don't have to be
recompiled, but if a module is recompiled, its pipe entry points
will need to be updated. If a module actually reached into the
pipe structures (unlikely), that would also need to be modified.
These changes substantially simplify failure handling in the pipe
code as there are many fewer possible failure modes.
On half-close, pipes no longer free the 'struct pipe' for the closed
half until a full-close takes place. However, VM mapped buffers
are still released on half-close.
Some code refactoring is now possible to clean up some of the back
references, etc; this patch attempts not to change the structure
of most of the pipe implementation, only allocation/free code
paths, so as to avoid introducing bugs (hopefully).
This cuts about 8%-9% off the cost of sequential pipe allocation
and free in system call tests on UP and SMP in my micro-benchmarks.
May or may not make a difference in macro-benchmarks, but doing
less work is good.
Reviewed by: juli, tjr
Testing help: dwhite, fenestro, scottl, et al
track the load for the sched_load() function. In the SMP case this member
is not defined because it would be redundant with the ksg_load member
which already tracks the non ithd load.
- For sched_load() in the UP case simply return ksq_sysload. In the SMP
case traverse the list of kseq groups and sum up their ksg_load fields.
of sched_load(). This variable tracks the number of running and runnable
non ithd threads. This removes the need to traverse the proc table and
discover how many threads are runnable.
at packet arrival.
For benchmarking purposes SO_BINTIME is preferable to SO_TIMEVAL
since it has higher resolution and lower overhead. Simultaneous
use of the two options is possible and they will return consistent
timestamps.
This introduces an extra test and a function call for SO_TIMEVAL, but I have
not been able to measure that.
and ffs_write(). These calls trace their origins to the dead vfs_ioopt
code, first appearing in revision 1.39 of ufs_readwrite.c.
Observed by: bde
Discussed with: tegge
interrupt handler so that no locks are needed, and schedules the
command completion routine with a taskqueue_fast. This also corrects the
locking in the command thread and removes the need for operation flags.
Simple load tests show that this is now considerably faster than FreeBSD 4.x
in the SMP case when multiple i/o tasks are running.
"scheduler" here has very little to do with scheduling. It is actually
the swapper, and it really must be the last SYSINIT'ed item like its
comment says, since proc0 metamorphoses into swapper by calling
scheduler() last in mi_start(), and scheduler() never returns.. Rev.1.29
of subr_4bsd.c broke this by adding another SI_ORDER_FIRST item
(kproc_start() for schedcpu_thread() onto the SI_SUB_RUN_SCHEDULER_LIST.
The sorting of SYSINITs with identical orders (at all levels) is
apparently nondeterministic, so this resulted in schedule() sometimes
being called second last and schedcpu_thread() not being called at all.
This quick fix just changes the code to almost match the comment
(SI_ORDER_FIRST -> SI_ORDER_ANY). "LAST" is misspelled "ANY", and
there is no way to ensure that there is only 1 very lst SYSINIT.
A more complete fix would remove the SYSINIT obfuscation.
won't associate in BSS mode if you use AUTHMODE_SHARED. I probably don't
understand enough to know when SHARED should be used vs. OPEN or WPA.
For now, go back to what works.
bit for this being the last CTIO2. It didn't matter since it really was the
last CTIO2 and the resources recycled, but still....
Add in CTIO3 define for future DAC work.
for direct-mapped addresses. Assume that any address less than KVA
is one of these and return it. Also assert that an address is KVA
does have a valid mapping - callers of pmap_kextract don't check
the return value, since they assume that they have a valid virtual
address.
addressing of memory. Makes a substantial improvement for apps that
stress the limited amount of KVM on PPC (e.g. untarring the ports tree).
uma_machdep.c stolen from amd64/ia64.
updated for the regparm ABI on amd64.
Context switch debug regs.
Update for fpu simplification
Don't needlessly reload %cr3, in case the cpu has the tlb flush filter
turned off. Re-add LAZY_SWITCH stubs.
profiling buffers and hash table. This makes it a lot easier to
do multiple profiling runs without rebooting or performing
gratuitous arithmetic. Sysctl is named debug.mutex.prof.reset.
Reviewed by: jake
- witness_lock() is split into two pieces: witness_checkorder() and
witness_lock(). Witness_checkorder() determines if acquiring a specified
lock at the time it is called would result in a lock order. It
optionally adds a new lock order relationship as well. witness_lock()
updates witness's data structures to assume that a lock has been acquired
by stick a new lock instance in the appropriate lock instance list.
- The mutex and sx lock functions now call checkorder() prior to trying to
acquire a lock and continue to call witness_lock() after the acquire is
completed. This will let witness catch a deadlock before it happens
rather than trying to do so after the threads have deadlocked (i.e. never
actually report it).
- A new function witness_defineorder() has been added that adds a lock
order between two locks at runtime without having to acquire the locks.
If the lock order cannot be added it will return an error. This function
is available to programmers via the WITNESS_DEFINEORDER() macro which
accepts either two mutexes or two sx locks as its arguments.
- A few simple wrapper macros were added to allow developers to call
witness_checkorder() anywhere as a way of enforcing locking assertions
in code that might acquire a certain lock in some situations. The
macros are: witness_check_{mutex,shared_sx,exclusive_sx} and take an
appropriate lock as the sole argument.
- The code to remove a lock instance from a lock list in witness_unlock()
was unnested by using a goto to vastly improve the readability of this
function.
instead of taskqueue_swi. This shaves from 1 to 10% of the overhead.
Overhaul the locking once more, there was a few possible races that
are now closed.
panic() so that the buffer overflow just beyond this point is always
caught, even when the code is not compiled with INVARIANTS.
Change chn_setblocksize() buffer reallocation code to attempt to avoid
the feed_vchan16() buffer overflow by attempting to always keep the
bufsoft buffer at least as large as the bufhard buffer.
Print a diagnositic message
Danger! %s bufsoft size increasing from %d to %d after CHANNEL_SETBLOCKSIZE()
if our best attempts fail. If feed_vchan16() were to be called by
the interrupt handler while locks are dropped in chn_setblocksize()
to increase the size bufsoft to match the size of bufhard, the panic()
code in feed_vchan16() will be triggered. If the diagnostic message
is printed, it is a warning that a panic is possible if the system
were to see events in an "unlucky" order.
Change the locking code to avoid the need for MTX_RECURSIVE mutexes.
Add the MTX_DUPOK option to the channel mutexes and change the locking
sequence to always lock the parent channel before its children to avoid
the possibility of deadlock.
Actually implement locking assertions for the channel mutexes and fix
the problems found by the resulting assertion violations.
Clean up the locking code in dsp_ioctl().
Allocate the channel buffers using the malloc() M_WAITOK option instead
of M_NOWAIT so that buffer allocation won't fail. Drop locks across
the malloc() calls.
Add/modify KASSERTS() in attempt to detect problems early.
Abuse layering by adding a pointer to the snd_dbuf structure that points
back to the pcm_channel that owns it. This allows sndbuf_resize() to do
proper locking without having to change the its API, which is used by
the hardware drivers.
Don't dereference a NULL pointer when setting hw.snd.maxautovchans
if a hardware driver is not loaded. Noticed by Ryan Sommers
<ryans at gamersimpact.com>.
Tested by: Stefan Ehmann <shoesoft AT gmx.net>
Tested by: matk (Mathew Kanner)
Tested by: Gordon Bergling <gbergling AT 0xfce3.net>
