the sscape/trix driver active, which (for some reason) disables the
mpu401 driver, causing an undefined reference to mpuintr. This was broken
with rev 1.79 (part of the PC98 nss driver commit).
range attributes after they have been extracted from the master.
Hook up the i686 MP code to do this for each AP.
Be more careful about printing the default memory type for the i686.
Suggestions from: luoqi
- %fs register is added to trapframe and saved/restored upon kernel entry/exit.
- Per-cpu pages are no longer mapped at the same virtual address.
- Each cpu now has a separate gdt selector table. A new segment selector
is added to point to per-cpu pages, per-cpu global variables are now
accessed through this new selector (%fs). The selectors in gdt table are
rearranged for cache line optimization.
- fask_vfork is now on as default for both UP and SMP.
- Some aio code cleanup.
Reviewed by: Alan Cox <alc@cs.rice.edu>
John Dyson <dyson@iquest.net>
Julian Elischer <julian@whistel.com>
Bruce Evans <bde@zeta.org.au>
David Greenman <dg@root.com>
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
Conditionally compile 386-specific code.
pmap_enter:
Eliminate unnecessary TLB shootdowns.
pmap_zero_page and pmap_zero_page_area:
Use invltlb_1pg instead of duplicating the code.
was only looking at old style drivers in the pcidevice_set, which doesn't
exist any more.. Ultimately, the pci and eisa bus drivers will check for
hints for wiring, flags and enable/disable etc as well.
conversion from short to unsigned long which is an argument of
bus_alloc_resource. Since the value -1 is used to indicate no port
reousece, id_port need to be signed (suggested by Doug Rabson and
Peter Wemm.)
With these changes plus the egcs fix I committed a few minutes ago,
"make -DWANT_AOUT world" works again. Most likely, "make upgrade"
is fixed too, though I haven't tested that.
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
because the act of doing the release kills the hints(!). A quirk of
the wrapper caused it to reset all the settings, except perhaps for the
memory address. I've tested this with a real SMC 8013EPC - which uses
shared memory addresses - it seems to work OK.
Use pmap_TLB_invalidate instead of invltlb_1pg to eliminate
unnecessary IPIs.
pmap_remove, pmap_protect and pmap_remove_pages:
Use pmap_TLB_invalidate_all instead of invltlb to eliminate
unnecessary IPIs.
pmap_copy:
Use cpu_invltlb instead of invltlb when updating APTDpde.
pmap_changebit:
Rather than deleting the unused "set bit" option (which may be
useful later), make pmap_changebit an inline that is used
by the new pmap_clearbit procedure.
Collectively, the first three changes reduce the number of TLB shootdown
IPIs by 1/3 for a kernel compile.
attached to the nexus. With one exception, this (for example) allows
you to do wierd things like kldload the eisa bus on the fly and then
drivers, and have it auto probe the eisa bus when the drivers come online.
The one exception being pci, it only adds the pcib after the presence of
the pci bus is detected and that's #if'ed code.
A side effect of this is that isa and eisa will be attached to the nexus
directly rather than the PCI->ISA or PCI->EISA bridges. I'm not sure if
this is good or bad at this point, but it seems to be closer to the way
things are for the i386 family... This is likely to be followed up.
This also fixes compilation without a PCI bus configured and will allow
eisa to work without PCI too.
- fix cut/paste problem. :-)
- don't forget to call isa_dmacascade()
- reset the port after we release resources.
That last one is a trap to watch out for.. The isa bus driver uses the
same port/irq/mem/etc variables for the initial probe hints as it does
for allocation/deallocation tracking. Releasing a resource clears the
variable and then you loose the hint during attach.. (ouch!)
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.
Submitted by: Doug Rabson <dfr@nlsystems.com>
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
only worked for configurations with "swap on generic".
usr.sbin/config/config.y:
- ignore all "swap [on] device ...' specifications except for
warning about them. They haven't done anything related to swap
for almost 4 years, and were previously silently ignored,
except for "swap on generic" which stopped swap${KERNEL}.c
from being generated. Code to support swapping is now deader
than before.
usr.sbin/config/mkswapconf.c:
- don't generate a dummy setconf() function in swap${KERNEL}.c.
sys/i386/conf/files.i386:
- swapgeneric.c is now standard. It should be merged into autoconf.c
so that it doesn't conflict with swap${KERNEL}.c for kernels named
"generic".
sys/i386/i386/autoconf.c:
- don't call setroot() for mfs roots. Since setroot() doesn't do anything
harmful, this was just a waste of time, except possibly for booting with
-a it may have helped prevent an undesireable call to setconf() by
finding a bogus rootdev.
- honor -a for ffs roots. -a now overrides all other ways of specifying
the root device. Previously, -r had precedence over -a, and the -a
handling was usually a no-op.
- don't honor -a for non-ffs roots, since it would currently just get in
the way of a clean panic.
sys/i386/i386/swapgeneric.c:
- don't declare things that are now always declared in swap${KERNEL}.c.
Don't decide things that are now decided in autoconf.c. Code to
support the "generic" case is now dead instead of useless.
in the RB_ASKNAME case. I had thought that I made this change in
rev.1.18, but rev.1.18 only affects obscure subcases of the
RB_DFLTROOT case (subcases where the compiled in default root is
not found in bdevsw[] -- then the root device is set to the first
device in the half-baked table that is also in bdevsw[]).
Removed yet more vestiges of config-time swap configuration.
All it did was match a specific device ID and turn on a quirk for
the wdc driver.
Incidently, at line 1462 there is a return that prevents the generic
ide_pci code from trying to look at the device. I'd be interested
to know if we can take out the return and let the generic code "see" it.
I've left the return in because that's the way it worked before.
(Be sure to rerun config after cvsup or you'll get undefined files!)
perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
Sense ${DEBUG} to decide on building kernel.debug or not.
Use a common install and install.debug target to minimize duplication.
(I deleted the ELF transition kernel warning, it was getting dated..)
Requested-by: ache
bde
dg
Modify targets for debug kernels: when -g was specified, make will
now build a debug kernel called kernel.debug, and create a stripped
version called kernel at the same time. The two targets install and
install.debug are otherwise unchanged.
Requested-by: dillon
Update man page accordingly.
