and libdevstat, since the new way of doing things is to just list
maintainership in src/MAINTAINERS.
Also, remove duplicate entries in src/MAINTAINERS for those utilities. I
already had entries for them.
variable RELEASE_BUILD_FIXIT is defined, a camcontrol binary will be
built that only knows the "rescan" and "reset" subcommands. The
resulting code is small enough to still fit onto the boot floppy.
Reviewed by: ken
MFC after: 1 week
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
related patches. These include:
* Mode page editting can be scripted. This involves two
things: first, if stdin is not a tty, changes are read from
stdin rather than invoking $EDITOR. Second, and more
importantly, not all modepage entries must be included in the
change set. This means that camcontrol can now gracefully handle
more intrusive editting from the $EDITOR, including removal or
rearrangement of lines. It also means that you can do stuff
like:
# echo "WCE: 1" | camcontrol modepage da3 -m 8 -e
# newfs /dev/da3
# echo "WCE: 0" | camcontrol modepage da3 -m 8 -e
* Range-checking on user-supplied input values. modeedit.c now
uses the field width specifiers to determine the maximum
allowable value for a field. If the user enters a value larger
than the maximum, it clips the value to the max and warns the
user. This also involved patching cam_cmdparse.c to be more
consistent with regards to the "count" parameter to arg_put
(previously is was the length of strings and 1 for all integral
types). The cam_cdbparse(3) man page was also updated to reflect
the revised semantics.
* In the process, I removed the 64 entry limit on mode pages (not
that we were even close to hitting that limit). This was a nice
side-effect of the other changes.
* Technically, the new mode editting functionality allows editting
of character array entries in mode pages (type 'c' or 'z'),
however since buff_encode doesn't grok them it is currently
useless.
* Camcontrol gained two new options related to mode pages: -l and
-b. The former lists all available mode pages for a given
device. The latter forces mode page display in binary format
(the default when no mode page definition was found in
scsi_modes).
* Added support for mode page names to scsi_modes. Allows names to
be displayed alongside mode numbers in the mode page
listing. Updated scsi_modes to use the new functionality. This
also adds the semicolon into the scsi_modes syntax as an
optional mode page definition terminator. This is needed to name
pages without providing a page format definition.
* Updated scsi_all.h to include a structure describing mode page
headers.
* Added $FreeBSD$ line to scsi_modes.
Inspired by: dwhite
Reviewed by: ken