Commit Graph

11 Commits

Author SHA1 Message Date
Jake Burkholder
e39756439c Back out the previous change to the queue(3) interface.
It was not discussed and should probably not happen.

Requested by:		msmith and others
2000-05-26 02:09:24 +00:00
Jake Burkholder
740a1973a6 Change the way that the queue(3) structures are declared; don't assume that
the type argument to *_HEAD and *_ENTRY is a struct.

Suggested by:	phk
Reviewed by:	phk
Approved by:	mdodd
2000-05-23 20:41:01 +00:00
Warner Losh
be8bcd17eb More pnpids. 2000-03-25 03:24:43 +00:00
Warner Losh
25f061dedd Fix plug and play support:
o Cut out the probed stuff.  We no longer need it since newbus implicitly
  checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload.  Untested because aha doesn't yet
  support identify and there are some interactions with PnP that I've
  not yet worked out.

With this I can boot the AHA-1542CP FW F.0.  All the aha resources
appear to be picked up via pnp now.
2000-01-24 07:08:40 +00:00
Peter Wemm
c3aac50f28 $Id$ -> $FreeBSD$ 1999-08-28 01:08:13 +00:00
Justin T. Gibbs
378d6d7395 The 1542 cards do not allow adapter commands to be queued while mailbox
commands are outstanding.  You'd think they'd just clear the IDLE bit,
but alas, no.  Delay until all pending mailbox commands have completed
in aha_cmd to work around this.

Report sync rates correctly on Fast Adaptec cards.  Clones may still be
reported incorrectly since there is no documenation on how they report
extended sync values.

Clean up some unused fields in the aha softc.
1999-05-25 20:15:20 +00:00
Warner Losh
07353d4247 o enable plug and play support for the aha driver. Given the cumbersome
pnp system in freebsd, I'm not sure how useful this will be, but my
  1542CP seems to work well in plug and play mode and does seem to
  probe correctly at all the oddball addresses/irq/drqs that I tried.
  [[
     I was unable to get /kernel.conf or /kernel.config to read in, so
     I wasn't able to verify that this method of userconfig works.  that's
     one thing that makes pnp so hard to use in the current scheme.
     Pointers to the right new way of doing this accepted.
  ]]
o Add some kludges to maybe bring support for 1540A/1542A into the
  driver.  Since I have no 154xA cards, and the only person I know
  that has them hasn't given me feedback, I'm making this commit
  blind.
o Honor unit numbers that are in the config file now.  This allows one
  to hard wire the unit numbers (and have high unit numbers for plug
  and pray devices, which can't seem to be hardwired) and have the
  cards not migrate from aha1 -> aha0 should aha0 go on the fritz.  I
  didn't verify that hard wired scsi busses would work, but did verify
  that hard wired aha addresses did work to a limited extent.  Both
  aha0 and aha1 must be hardwired, or when the card that was in aha0
  goes away, the probe for aha0 might pick up the card that otherwise
  would have been aha1.
1999-01-20 06:21:27 +00:00
Justin T. Gibbs
d0993d7584 Fix probes when a port address is specified.
Convert from BT'isms to AHA'isms

Don't fail the probe if the illegal command bit is set in the status
register.  If the BusLogic MultiMaster probe preceeded us, it may well
have determined that the card we are attaching to was not a true MultiMaster
by sending us a command that fails on the 154X.

Reset the adapter before doing the inquiry.  This provides extra sanity
and will also clear the illegal command status bit that my be left over
from the MultiMaster probe.
1998-11-10 06:44:42 +00:00
Warner Losh
27af0eb7b6 GC unused stuff. 1998-10-02 04:37:49 +00:00
Warner Losh
667b14c256 Misc cleanup and probe rework:
o Use the board id command to find out what kind of board
	  we're talking to.  If we're talking to a board that is has
	  an ID that is shared between boards supported by the aha
	  driver and the bt driver, then use the bt's geometry
	  register to weed out the bt cards.  Otherwise assume that we
	  support this card.
	o Remove bt esetup command sending to the card.  It seems to
	  wedge too many cards.
	o Revert to doing a soft reset after an invalid command.  This
	  change didn't fix anything, so I'm backing it out.  The
	  whole issue of card resetting needs to be revisisted at some
	  point so that we can do it properly on all hardware.
	o GC unused stuff in some places.
1998-10-01 04:53:55 +00:00
Justin T. Gibbs
5d55526b65 Adaptec 154X SCSI-Host Adapter driver for CAM.
Submitted by:	Warner Losh <imp@village.org>
1998-09-15 07:39:55 +00:00