seems to be necessary for the 8139C+ under certain circumstances, and
doesn't appear to hurt the other chips. (In the failure case, the
packet would be sent through the TX DMA ring but not get echoed
back. I suspect this has something to do with the link state changing
unexpectedly.)
autoload and then copying the contends of the station address
registers. For some reason, reading the EEPROM on the 8169S doesn't
work right. This gets around the problem, and allows us to read
the station address correctly on the 8169S.
- Insert a delay after initiating packet transmition in re_diag() to
allow lots of time for the frame to echo back to the host, and wait
for both the 'RX complete' and 'timeout expired' bits in the ISR
register to be set.
- Deal more intelligently with the fact that the frame length
field in the RX descriptor is a different width on the 8139C+
than it is on the 8169/8169S/8110S
- For the 8169, you have to set bit 17 in the TX config register
to enter digital loopback mode, but for the 8139C+, you have to
set both bits 17 and 18. Take this into account so that re_diag()
works properly for both types of chips.
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
we think is the correct trigger mode and polarity. This allows us to
implement BUS_CONFIG_INTR() as an update of the RTE in question.
Consequently, we can trust the RTE when we enable an interrupt and
avoids that we need to know about the trigger mode and polarity at
that time.
method. This is necessary on ia64 where it's known that serial interfaces
described in the ACPI namespace may not have the well-known IRQs assigned
to them. This confuses us in thinking they are PCI based interrupts and
wrongly program the APIC.
but has invalid 64 bit pointers for FACS and DSDT.
o Finish work to print all of the FADT and FACS.
o Resort the comment generating functions. Submitted by: marcel
Courtesy of: BSDcon back wall
about interrupt trigger mode and interrupt polarity. This allows ACPI
for example to pass interrupt resource information up the hierarchy.
The default implementation of the method therefore is to pass the
request to the parent.
Reviewed by: jhb, njl
- Add 'enable_exim="YES"' to rc.conf(5)
- Use the default exim configuration file from the port
- When using sendmail, disable some more scripts that use sendmail specific
parameters
- Have sysinstall tweak mailer.conf(5) substitution
- Use 'N' flag for newsyslog(8)
Submitted by: Oliver Eikemeier <eikemeier@fillmore-labs.com>
Reviewed by: sheldonh, simon
Tested by: myself (trhodes) and submitter
for the 8169S, according to my sample board. The RealTek Linux driver
mentions 0x00800000. I'm assigning this to the 8110S until I get
more info on it. (The (preliminary) RealTek docs only say that 8169S/8110S
chips will have some combination of those two bits set, but doesn't say
exactly what bit combination goes with which chip variant.)
intpin register is expressed in hardware where 0 means none, 1 means INTA,
2 INTB, etc. The other way is commonly used in loops where 0 means INTA,
1 means INTB, etc. The matchpin argument to pci_cfgintr_search() is
supposed to be the first form, but we passsed in a loop index of the
second. This fix adds one to the loop index to convert to the first form.
Reported by: Pavlin Radoslavov <pavlin@icir.org>
is not a size of 1. Since we already know there is a FIFO, we can
safely assume that it is at least 16 bytes. Note that all this is
mostly academic anyway. We don't use the size of the Rx FIFO
currently. If we add support for hardware flow control, we only
care about Rx FIFO sizes larger than 16.
