a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
On some architectures, u_long isn't large enough for resource definitions.
Particularly, powerpc and arm allow 36-bit (or larger) physical addresses, but
type `long' is only 32-bit. This extends rman's resources to uintmax_t. With
this change, any resource can feasibly be placed anywhere in physical memory
(within the constraints of the driver).
Why uintmax_t and not something machine dependent, or uint64_t? Though it's
possible for uintmax_t to grow, it's highly unlikely it will become 128-bit on
32-bit architectures. 64-bit architectures should have plenty of RAM to absorb
the increase on resource sizes if and when this occurs, and the number of
resources on memory-constrained systems should be sufficiently small as to not
pose a drastic overhead. That being said, uintmax_t was chosen for source
clarity. If it's specified as uint64_t, all printf()-like calls would either
need casts to uintmax_t, or be littered with PRI*64 macros. Casts to uintmax_t
aren't horrible, but it would also bake into the API for
resource_list_print_type() either a hidden assumption that entries get cast to
uintmax_t for printing, or these calls would need the PRI*64 macros. Since
source code is meant to be read more often than written, I chose the clearest
path of simply using uintmax_t.
Tested on a PowerPC p5020-based board, which places all device resources in
0xfxxxxxxxx, and has 8GB RAM.
Regression tested on qemu-system-i386
Regression tested on qemu-system-mips (malta profile)
Tested PAE and devinfo on virtualbox (live CD)
Special thanks to bz for his testing on ARM.
Reviewed By: bz, jhb (previous)
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D4544
In dual emac mode, the CPSW subsystem provides two independent ethernets.
This is implemented (as recommended by TI's TRM) with a mixture of switch
settings (vlans) and specific features of CPSW subsystem.
The driver was splitted to accommodate the shared parts (RX and TX rings
for example) while it still provides two independent ethernets.
Each of the ethernet ports driver has it's own set of MDIO registers among
the other private settings.
Previously this driver always operate in promisc mode, now the Switch ALE
(address table entry) is properly initialized and enabled.
The driver is also tested (and known to work) with both ports operating in
single port mode (active_slave 0 or 1).
Tested on uBMC (dual emac mode, both ports in single mode, giga and fast
ethernet) and BBB (single port, fast ethernet).
Sponsored by: Rubicon Communications (Netgate)
We changed the ABI for ARM in 10, an removed support for the old ABI in 11,
as such binaries from these releases are unable to be run on a head kernel.
Reviewed by: bz, emast
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5652
r296861 addressed a build failure due to undefined SYS_freebsd6_lseek
by adding a COMPAT_FREEBSD6 conditional, but we do not support FreeBSD 6
compatibility on armeb anyway so remove it completely.
Reviewed by: andrew, bz
Differential Revision: https://reviews.freebsd.org/D5643
the ABI in 10.0, and have removed support for the old ABI in 11. As such
any of these options to provide compatibility prior to 10 are unneeded.
Sponsored by: ABT Systems Ltd
The following pheripherals are supported: UART, MMC, AHCI, EHCI, PCIe, I2C,
PMIC, GPIO, CPU temperature and clock.
Note: The PCIe driver is pure mash at this moment. It will be reworked
immediately when both D5237 and D2579 enter the current tree.
This commit provides attachment of xhci-platform for A38X boards, making
it possible to mount FreeBSD world from USB3.0 flash. 'xhci' device was
added to files.mv (as optional) and kernconf of Armada38x was enhanced.
It was also necessary to open programmable memory windows of USB3.0.
fdt_win_setup needed improvement so it's able to traverse through
children of internal-regs node.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: hselasky
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5031
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
code for the A20 to use the new PLATFORM_SMP interface, and extends it to
add support for the new SoCs allowing for both to coexist within the same
kernel.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D5342
adds a lock to ensure only a single device is accessing the hardware. A
reference count is added to only enable when we start to use the clock,
and to disable after we have finished needing the clock.
This was extracted from a larger review to add OHCI support to the
Allwinner SoCs.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
X-Differential Revision: https://reviews.freebsd.org/D5481
Very similar to the A10 RTC controller with a few register offsets changed
and a different location for the LOSC switch status.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5500
taskqueue_enqueue() was changed to support both fast and non-fast
taskqueues 10 years ago in r154167. It has been a compat shim ever
since. It's time for the compat shim to go.
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: sephe
Differential Revision: https://reviews.freebsd.org/D5131
is the physical memory size so may be larger than a u_long can hold, e.g.
on ARM with LPAE we could see an address space of up to 40 bits. On ARM
u_long is only 32 bits so the memory size will be truncated, possibly to
zero.
Reported by: bz
Sponsored by: ABT Systems Ltd
Summary:
As part of the migration of rman_res_t to be typed to uintmax_t, memory ranges
must be clamped appropriately for the bus, to prevent completely bogus addresses
from being used.
This is extracted from D4544.
Reviewed By: cem
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5134
Use u_long instead of uint32_t variables to avoid overflow
in case of PA space bigger than 32-bit.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Approved by: cognet (mentor)
Reviewed by: andrew, br, wma
Differential revision: https://reviews.freebsd.org/D5393
different methods to start the secondary cores in a kernel built for
multiple SoCs, e.g. with the Allwinner A20 and A31.
Sponsored by: ABT systems Ltd
Differential Revision: https://reviews.freebsd.org/D5466
Newer Allwinner MMC implementations use a different FIFO register offset
(0x200 instead of 0x100). Since the FDT uses the same compat string for
both cases, base the decision on which FIFO offset to use on the Allwinner
SoC family.
Reviewed by: Emmanuel Vadot <manu@bidouilliste.com>
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5468
the interrupt framework is also going to be used by another (MIPS)
architecture. IPI implementations may vary much across different
architectures.
An IPI implementation should still define INTR_IPI_COUNT and use
intr_ipi_setup_counters() to setup IPI counters which are inside of
intrcnt[] and intrnames[] arrays. Those are used for sysctl and ddb.
Then, intr_ipi_increment_count() should be used to increment obtained
counter.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D5459
Most calls to bus_alloc_resource() use "anywhere" as the range, with a given
count. Migrate these to use the new bus_alloc_resource_anywhere() API.
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D5370
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
support for the i2c, mmc, and gmac clocks. Further clocks can be added as
needed.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D5339
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
driver. This mostly involves selecting the register offsets to use at
runtime based on the hardware we are talking to.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5327
