A single polynomial approximation for tan(x) works in infinite precision
up to |x| < pi/2, but in finite precision, to restrict the accumulated
roundoff error to < 1 ulp, |x| must be restricted to less than about
sqrt(0.5/((1.5+1.5)/3)) ~= 0.707. We restricted it a bit more to
give a safety margin including some slop for optimizations. Now that
we use double precision for the calculations, the accumulated roundoff
error is in double-precision ulps so it can easily be made almost 2**29
times smaller than a single-precision ulp. Near x = pi/4 its maximum
is about 0.5+(1.5+1.5)*x**2/3 ~= 1.117 double-precision ulps.
The minimax polynomial needs to be different to work for the larger
interval. I didn't increase its degree the old degree is just large
enough to keep the final error less than 1 ulp and increasing the
degree would be a pessimization. The maximum error is now ~0.80
ulps instead of ~0.53 ulps.
The speedup from this optimization for uniformly distributed args in
[-2pi, 2pi] is 28-43% on athlons, depending on how badly gcc selected
and scheduled the instructions in the old version. The old version
has some int-to-float conversions that are apparently difficult to schedule
well, but gcc-3.3 somehow did everything ~10 cycles or ~10% faster than
gcc-3.4, with the difference especially large on AXPs. On A64s, the
problem seems to be related to documented penalties for moving single
precision data to undead xmm registers. With this version, the speed
is cycles is almost independent of the athlon and gcc version despite
the large differences in instruction selection to use the FPU on AXPs
and SSE on A64s.
This is a minor interface change. The function is renamed from
__kernel_tanf() to __kernel_tandf() so that misues of it will cause
link errors and not crashes.
This version is a routine translation with no special optimizations
for accuracy or efficiency. It gives an unimportant increase in
accuracy, from ~0.9 ulps to 0.5285 ulps. Almost all of the error is
from the minimax polynomial (~0.03 ulps and the final rounding step
(< 0.5 ulps). It gives strange differences in efficiency in the -5
to +10% range, with -O1 fairly consistently becoming faster and -O2
slower on AXP and A64 with gcc-3.3 and gcc-3.4.
arg to __kernel_rem_pio2() gives 53-bit (double) precision, not single
precision and/or the array dimension like I thought. prec == 2 is
used in e_rem_pio2.c for double precision although it is documented
to be for 64-bit (extended) precision, and I just reduced it by 1
thinking that this would give the value suitable for 24-bit (float)
precision. Reducing it 1 more to the documented value for float
precision doesn't actually work (it gives errors of ~0.75 ulps in the
reduced arg, but errors of much less than 0.5 ulps are needed; the bug
seems to be in kernel_rem_pio2.c). Keep using a value 1 larger than
the documented value but supply an array large enough hold the extra
unused result from this.
The bug can also be fixed quickly by increasing init_jk[0] in
k_rem_pio2.c from 2 to 3. This gives behaviour identical to using
prec == 1 except it doesn't create the extra result. It isn't clear
how the precision bug affects higher precisions. 113-bit (quad) is
the largest precision, so there is no way to use a large precision
to fix it.
they can be #included in other .c files to give inline functions, and
use them to inline the functions in most callers (not in e_lgammaf_r.c).
__kernel_tanf() is too large and complicated for gcc to inline very well.
An athlons, this gives a speed increase under favourable pipeline
conditions of about 10% overall (larger for AXP, smaller for A64).
E.g., on AXP, sinf() on uniformly distributed args in [-2Pi, 2Pi]
now takes 30-56 cycles; it used to take 45-61 cycles; hardware fsin
takes 65-129.
On athlons, this gives a speedup of 10-20% for tanf() on uniformly
distributed args in [-2Pi, 2Pi]. (It only directly applies for 43%
of the args and gives a 16-20% speedup for these (more for AXP than
A64) and this gives an overall speedup of 10-12% which is all that it
should; however, it gives an overall speedup of 17-20% with gcc-3.3
on AXP-A64 by mysteriously effected cases where it isn't executed.)
I originally intended to use double precision for all internals of
float trig functions and will probably still do this, but benchmarking
showed that converting to double precision and back is a pessimization
in cases where a simple float precision calculation works, so it may
be optimal to switch precisions only when using extra precision is
much simpler.
__ieee754_rem_pio2f() to its 3 callers and manually inline them.
On Athlons, with favourable compiler flags and optimizations and
favourable pipeline conditions, this gives a speedup of 30-40 cycles
for cosf(), sinf() and tanf() on the range pi/4 < |x| <= 9pi/4, so
thes functions are now signifcantly faster than the hardware trig
functions in many cases. E.g., in a benchmark with uniformly distributed
x in [-2pi, 2pi], A64 hardware fcos took 72-129 cycles and cosf() took
37-55 cycles. Out-of-order execution is needed to get both of these
times. The optimizations in this commit apparently work more by
removing 1 serialization point than by reducing latency.
s_cosf.c and s_sinf.c:
Use a non-bogus magic constant for the threshold of pi/4. It was 2 ulps
smaller than pi/4 rounded down, but its value is not critical so it should
be the result of natural rounding.
s_cosf.c and s_tanf.c:
Use a literal 0.0 instead of an unnecessary variable initialized to
[(float)]0.0. Let the function prototype convert to 0.0F.
Improved wording in some comments.
Attempted to improve indentation of comments.
number of branches.
Use a non-bogus magic constant for the threshold of pi/4. It was 2 ulps
smaller than pi/4 rounded down, but its value is not critical so it should
be the result of natural rounding. Use "<=" comparisons with rounded-
down thresholds for all small multiples of pi/4.
Cleaned up previous commit:
- use static const variables instead of expressions for multiples of pi/2
to ensure that they are evaluated at compile time. gcc currently
evaluates them at compile time but C99 compilers are not required
to do so. We want compile time evaluation for optimization and don't
care about side effects.
- use M_PI_2 instead of a magic constant for pi/2. We need magic constants
related to pi/2 elsewhere but not here since we just want pi/2 rounded
to double and even prefer it to be rounded in the default rounding mode.
We can depend on the cmpiler being C99ish enough to round M_PI_2 correctly
just as much as we depended on it handling hex constants correctly. This
also fixes a harmless rounding error in the hex constant.
- keep using expressions n*<value for pi/2> in the initializers for the
static const variables. 2*M_PI_2 and 4*M_PI_2 are obviously rounded in
the same way as the corresponding infinite precision expressions for
multiples of pi/2, and 3*M_PI_2 happens to be rounded like this, so we
don't need magic constants for the multiples.
- fixed and/or updated some comments.
define also, but res_config.h was not included into libc/net/name6.c.
So getipnodebyaddr() ignored the multiple PTRs.
PR: kern/88241
Submitted by: Dan Lukes <dan__at__obluda.cz>
MFC after: 3 days
The threshold for not being tiny was too small. Use the usual 2**-12
threshold. This change is not just an optimization, since the general
code that we fell into has accuracy problems even for tiny x. Avoiding
it fixes 2*1366 args with errors of more than 1 ulp, with a maximum
error of 1.167 ulps.
The magic number 22 is log(DBL_EPSILON)/2 plus slop. This is bogus
for float precision. Use 9 (~log(FLT_EPSILON)/2 plus less slop than
for double precision). The code for handling the interval
[2**-28, 9_was_22] has accuracy problems even for [9, 22], so this
change happens to fix errors of more than 1 ulp in about 2*17000
cases. It leaves such errors in about 2*1074000 cases, with a max
error of 1.242 ulps.
The threshold for switching from returning exp(x)/2 to returning
exp(x/2)^2/2 was a little smaller than necessary. As for coshf(),
This was not quite harmless since the exp(x/2)^2/2 case is inaccurate,
and fixing it avoids accuracy problems in 2*6 cases, leaving problems
in 2*19997 cases.
Fixed naming errors in pseudo-code in comments.
The threshold for not being tiny was confusing and too small. Use the
usual 2**-12 threshold and simplify the algorithm slightly so that
this threshold works (now use the threshold for sinhf() instead of one
for 1+expm1()). This is just a small optimization.
The magic number 22 is log(DBL_EPSILON)/2 plus slop. This is bogus
for float precision. Use 9 (~log(FLT_EPSILON)/2 plus less slop than
for double precision).
The threshold for switching from returning exp(x)/2 to returning
exp(x/2)^2/2 was a little smaller than necessary. This was not quite
harmless since the exp(x/2)^2/2 case is inaccurate. Fixing it happens
to avoid accuracy problems for 2*6 of the 2*151 args that were handled
by the exp(x)/2 case. This leaves accuracy problems for about 2*19997
args near the overflow threshold (~89); the maximum error there is
2.5029 ulps.
There are also accuracy probles for args in +-[0.5*ln2, 9] -- 2*188885
args with errors of more than 1 ulp, with a maximum error of 1.384 ulps.
Fixed a syntax error and naming errors in pseudo-code in comments.
specialized for float precision. The new polynomial has degree 8
instead of 14, and a maximum error of 2**-34.34 (absolute) instead of
2**-30.66. This doesn't affect the final error significantly; the
maximum error was and is about 0.8879 ulps on amd64 -01.
The fdlibm expf() is not used on i386's (the "optimized" asm version
is used), but probably should be since it was already significantly
faster than the asm version on athlons. The asm version has the
advantage of being more accurate, so keep using it for now.
polynomial for __kernel_tanf(). The old one was the double-precision
polynomial with coefficients truncated to float. Truncation is not
a good way to convert minimax polynomials to lower precision. Optimize
for efficiency and use the lowest-degree polynomial that gives a
relative error of less than 1 ulp. It has degree 13 instead of 27,
and happens to be 2.5 times more accurate (in infinite precision) than
the old polynomial (the maximum error is 0.017 ulps instead of 0.041
ulps).
Unlike for cosf and sinf, the old accuracy was close to being inadequate
-- the polynomial for double precision has a max error of 0.014 ulps
and nearly this small an error is needed. The new accuracy is also a
bit small, but exhaustive checking shows that even the old accuracy
was enough. The increased accuracy reduces the maximum relative error
in the final result on amd64 -O1 from 0.9588 ulps to 0.9044 ulps.
special case pi/4 <= |x| < 3*pi/4. This gives a tiny optimization (it
saves 2 subtractions, which are scheduled well so they take a whole 1
cycle extra on an AthlonXP), and simplifies the code so that the
following optimization is not so ugly.
Optimize for the range 3*pi/4 < |x| < 9*Pi/2 in the same way. On
Athlon{XP,64} systems, this gives a 25-40% optimization (depending a
lot on CFLAGS) for the cosf() and sinf() consumers on this range.
Relative to i387 hardware fcos and fsin, it makes the software versions
faster in most cases instead of slower in most cases. The relative
optimization is smaller for tanf() the inefficient part is elsewhere.
The 53-bit approximation to pi/2 is good enough for pi/4 <= |x| <
3*pi/4 because after losing up to 24 bits to subtraction, we still
have 29 bits of precision and only need 25 bits. Even with only 5
extra bits, it is possible to get perfectly rounded results starting
with the reduced x, since if x is nearly a multiple of pi/2 then x is
not near a half-way case and if x is not nearly a multiple of pi/2
then we don't lose many bits. With our intentionally imperfect rounding
we get the same results for cosf(), sinf() and tanf() as without this
optimization.
standard in C99 and POSIX.1-2001+. They are also not deprecated, since
apart from being standard they can handle special args slightly better
than the ilogb() functions.
Move their documentation to ilogb.3. Try to use consistent and improved
wording for both sets of functions. All of ieee854, C99 and POSIX
have better wording and more details for special args.
Add history for the logb() functions and ilogbl(). Fix history for
ilogb().
so that it can be faster for tiny x and avoided for reduced x.
This improves things a little differently than for cosine and sine.
We still need to reclassify x in the "kernel" functions, but we get
an extra optimization for tiny x, and an overall optimization since
tiny reduced x rarely happens. We also get optimizations for space
and style. A large block of poorly duplicated code to fix a special
case is no longer needed. This supersedes the fixes in k_sin.c revs
1.9 and 1.11 and k_sinf.c 1.8 and 1.10.
Fixed wrong constant for the cutoff for "tiny" in tanf(). It was
2**-28, but should be almost the same as the cutoff in sinf() (2**-12).
The incorrect cutoff protected us from the bugs fixed in k_sinf.c 1.8
and 1.10, except 4 cases of reduced args passed the cutoff and needed
special handling in theory although not in practice. Now we essentially
use a cutoff of 0 for the case of reduced args, so we now have 0 special
args instead of 4.
This change makes no difference to the results for sinf() (since it
only changes the algorithm for the 4 special args and the results for
those happen not to change), but it changes lots of results for sin().
Exhaustive testing is impossible for sin(), but exhaustive testing
for sinf() (relative to a version with the old algorithm and a fixed
cutoff) shows that the changes in the error are either reductions or
from 0.5-epsilon ulps to 0.5+epsilon ulps. The new method just uses
some extra terms in approximations so it tends to give more accurate
results, and there are apparently no problems from having extra
accuracy. On amd64 with -O1, on all float args the error range in ulps
is reduced from (0.500, 0.665] to [0.335, 0.500) in 24168 cases and
increased from 0.500-epsilon to 0.500+epsilon in 24 cases. Non-
exhaustive testing by ucbtest shows no differences.
commit moved it). This includes a comment that the "kernel" sine no
longer works on arg -0, so callers must now handle this case. The kernel
sine still works on all other tiny args; without the optimization it is
just a little slower on these args. I intended it to keep working on
all tiny args, but that seems to be impossible without losing efficiency
or accuracy. (sin(x) ~ x * (1 + S1*x**2 + ...) would preserve -0, but
the approximation must be written as x + S1*x**3 + ... for accuracy.)
case never occurs since pi/2 is irrational so no multiple of it can
be represented as a float and we have precise arg reduction so we never
end up with a remainder of 0 in the "kernel" function unless the
original arg is 0.
If this case occurs, then we would now fall through to general code
that returns +-Inf (depending on the sign of the reduced arg) instead
of forcing +Inf. The correct handling would be to return NaN since
we would have lost so much precision that the correct result can be
anything _except_ +-Inf.
Don't reindent the else clause left over from this, although it was already
bogusly indented ("if (foo) return; else ..." just marches the indentation
to the right), since it will be removed too.
Index: k_tan.c
===================================================================
RCS file: /home/ncvs/src/lib/msun/src/k_tan.c,v
retrieving revision 1.10
diff -r1.10 k_tan.c
88,90c88
< if (((ix | low) | (iy + 1)) == 0)
< return one / fabs(x);
< else {
---
> {
a declaration was not translated to "float" although bit fiddling on
double variables was translated. This resulted in garbage being put
into the low word of one of the doubles instead of non-garbage being
put into the only word of the intended float. This had no effect on
any result because:
- with doubles, the algorithm for calculating -1/(x+y) is unnecessarily
complicated. Just returning -1/((double)x+y) would work, and the
misdeclaration gave something like that except for messing up some
low bits with the bit fiddling.
- doubles have plenty of bits to spare so messing up some of the low
bits is unlikely to matter.
- due to other bugs, the buggy code is reached for a whole 4 args out
of all 2**32 float args. The bug fixed by 1.8 only affects a small
percentage of cases and a small percentage of 4 is 0. The 4 args
happen to cause no problems without 1.8, so they are even less likely
to be affected by the bug in 1.8 than average args; in fact, neither
1.8 nor this commit makes any difference to the result for these 4
args (and thus for all args).
Corrections to the log message in 1.8: the bug only applies to tan()
and not tanf(), not because the float type can't represent numbers
large enough to trigger the problem (e.g., the example in the fdlibm-5.3
readme which is > 1.0e269), but because:
- the float type can't represent small enough numbers. For there to be
a possible problem, the original arg for tanf() must lie very near an
odd multiple of pi/2. Doubles can get nearer in absolute units. In
ulps there should be little difference, but ...
- ... the cutoff for "small" numbers is bogus in k_tanf.c. It is still
the double value (2**-28). Since this is 32 times smaller than
FLT_EPSILON and large float values are not very uniformly distributed,
only 6 args other than ones that are initially below the cutoff give
a reduced arg that passes the cutoff (the 4 problem cases mentioned
above and 2 non-problem cases).
Fixing the cutoff makes the bug affect tanf() and much easier to detect
than for tan(). With a cutoff of 2**-12 on amd64 with -O1, 670102
args pass the cutoff; of these, there are 337604 cases where there
might be an error of >= 1 ulp and 5826 cases where there is such an
error; the maximum error is 1.5382 ulps.
The fix in 1.8 works with the reduced cutoff in all cases despite the
bug in it. It changes the result in 84492 cases altogether to fix the
5826 broken cases. Fixing the fix by translating "double" to "float"
changes the result in 42 cases relative to 1.8. In 24 cases the
(absolute) error is increased and in 18 cases it is reduced, but it
remains less than 1 ulp in all cases.
rewritten, now timers created with same sigev_notify_attributes will
run in same thread, this allows user to organize which timers can
run in same thread to save some thread resource.
The log message for 1.5 said that some small (one or two ulp) inaccuracies
were fixed, and a comment implied that the critical change is to switch
the rounding mode to to-nearest, with a switch of the precision to
extended at no extra cost. Actually, the errors are very large (ucbtest
finds ones of several hundred ulps), and it is the switch of the
precision that is critical.
Another comment was wrong about NaNs being handled sloppily.
and medium size args too: instead of conditionally subtracting a float
17+24, 17+17+24 or 17+17+17+24 bit approximation to pi/2, always
subtract a double 33+53 bit one. The float version is now closer to
the double version than to old versions of itself -- it uses the same
33+53 bit approximation as the simplest cases in the double version,
and where the float version had to switch to the slow general case at
|x| == 2^7*pi/2, it now switches at |x| == 2^19*pi/2 the same as the
double version.
This speeds up arg reduction by a factor of 2 for |x| between 3*pi/4 and
2^7*pi/4, and by a factor of 7 for |x| between 2^7*pi/4 and 2^19*pi/4.
using under FreeBSD. Before this commit, all float precision functions
except exp2f() were implemented using only float precision, apparently
because Cygnus needed this in 1993 for embedded systems with slow or
inefficient double precision. For FreeBSD, except possibly on systems
that do floating point entirely in software (very old i386 and now
arm), this just gives a more complicated implementation, many bugs,
and usually worse performance for float precision than for double
precision. The bugs and worse performance were particulary large in
arg reduction for trig functions. We want to divide by an approximation
to pi/2 which has as many as 1584 bits, so we should use the widest
type that is efficient and/or easy to use, i.e., double. Use fdlibm's
__kernel_rem_pio2() to do this as Sun apparently intended. Cygnus's
k_rem_pio2f.c is now unused. e_rem_pio2f.c still needs to be separate
from e_rem_pio2.c so that it can be optimized for float args. Similarly
for long double precision.
This speeds up cosf(x) on large args by a factor of about 2. Correct
arg reduction on large args is still inherently very slow, so hopefully
these args rarely occur in practice. There is much more efficiency
to be gained by using double precision to speed up arg reduction on
medium and small float args.
__kernel_sinf(). The old ones were the double-precision polynomials
with coefficients truncated to float. Truncation is not a good way
to convert minimax polynomials to lower precision. Optimize for
efficiency and use the lowest-degree polynomials that give a relative
error of less than 1 ulp -- degree 8 instead of 14 for cosf and degree
9 instead of 13 for sinf. For sinf, the degree 8 polynomial happens
to be 6 times more accurate than the old degree 14 one, but this only
gives a tiny amount of extra accuracy in results -- we just need to
use a a degree high enough to give a polynomial whose relative accuracy
in infinite precision (but with float coefficients) is a small fraction
of a float ulp (fdlibm generally uses 1/32 for the small fraction, and
the fraction for our degree 8 polynomial is about 1/600).
The maximum relative errors for cosf() and sinf() are now 0.7719 ulps
and 0.7969 ulps, respectively.
This supersedes the fix for the old algorithm in rev.1.8 of k_cosf.c.
I want this change mainly because it is an optimization. It helps
make software cos[f](x) and sin[f](x) faster than the i387 hardware
versions for small x. It is also a simplification, and reduces the
maximum relative error for cosf() and sinf() on machines like amd64
from about 0.87 ulps to about 0.80 ulps. It was validated for cosf()
and sinf() by exhaustive testing. Exhaustive testing is not possible
for cos() and sin(), but ucbtest reports a similar reduction for the
worst case found by non-exhaustive testing. ucbtest's non-exhaustive
testing seems to be good enough to find problems in algorithms but not
maximum relative errors when there are spikes. E.g., short runs of
it find only 3 ulp error where the i387 hardware cos() has an error
of about 2**40 ulps near pi/2.
to floats (mainly i386's). All errors of more than 1 ulp for float
precision trig functions were supposed to have been fixed; however,
compiling with gcc -O2 uncovered 18250 more such errors for cosf(),
with a maximum error of 1.409 ulps.
Use essentially the same fix as in rev.1.8 of k_rem_pio2f.c (access a
non-volatile variable as a volatile). Here the -O1 case apparently
worked because the variable is in a 2-element array and it takes -O2
to mess up such a variable by putting it in a register.
The maximum error for cosf() on i386 with gcc -O2 is now 0.5467 (it
is still 0.5650 with gcc -O1). This shows that -O2 still causes some
extra precision, but the extra precision is now good.
Extra precision is harmful mainly for implementing extra precision in
software. We want to represent x+y as w+r where both "+" operations
are in infinite precision and r is tiny compared with w. There is a
standard algorithm for this (Knuth (1981) 4.2.2 Theorem C), and fdlibm
uses this routinely, but the algorithm requires w and r to have the
same precision as x and y. w is just x+y (calculated in the same
finite precision as x and y), and r is a tiny correction term. The
i386 gcc bugs tend to give extra precision in w, and then using this
extra precision in the calculation of r results in the correction
mostly staying in w and being missing from r. There still tends to
be no problem if the result is a simple expression involving w and r
-- modulo spills, w keeps its extra precision and r remains the right
correction for this wrong w. However, here we want to pass w and r
to extern functions. Extra precision is not retained in function args,
so w gets fixed up, but the change to the tiny r is tinier, so r almost
remains as a wrong correction for the right w.
{cos_sin}[f](x) so that x doesn't need to be reclassified in the
"kernel" functions to determine if it is tiny (it still needs to be
reclassified in the cosine case for other reasons that will go away).
This optimization is quite large for exponentially distributed x, since
x is tiny for almost half of the domain, but it is a pessimization for
uniformally distributed x since it takes a little time for all cases
but rarely applies. Arg reduction on exponentially distributed x
rarely gives a tiny x unless the reduction is null, so it is best to
only do the optimization if the initial x is tiny, which is what this
commit arranges. The imediate result is an average optimization of
1.4% relative to the previous version in a case that doesn't favour
the optimization (double cos(x) on all float x) and a large
pessimization for the relatively unimportant cases of lgamma[f][_r](x)
on tiny, negative, exponentially distributed x. The optimization should
be recovered for lgamma*() as part of fixing lgamma*()'s low-quality
arg reduction.
Fixed various wrong constants for the cutoff for "tiny". For cosine,
the cutoff is when x**2/2! == {FLT or DBL}_EPSILON/2. We round down
to an integral power of 2 (and for cos() reduce the power by another
1) because the exact cutoff doesn't matter and would take more work
to determine. For sine, the exact cutoff is larger due to the ration
of terms being x**2/3! instead of x**2/2!, but we use the same cutoff
as for cosine. We now use a cutoff of 2**-27 for double precision and
2**-12 for single precision. 2**-27 was used in all cases but was
misspelled 2**27 in comments. Wrong and sloppy cutoffs just cause
missed optimizations (provided the rounding mode is to nearest --
other modes just aren't supported).
readable on certain random memory configurations. If the libkvm consumer
tried to read something that was in the very last pdpe, pde or pte slot,
it would bogusly fail.
This is broken in RELENG_6 too.
expr and printf are not available during installworld, so
use /bin/sh arithmetic expansion instead of expr and simply
give up on vanity formatting. ;-)
systems (or on FreeBSD systems when using ports).
2) Overhaul the versioning logic. In particular,
SHLIB_MAJOR number is now computed as "major+minor",
which ensures library versions are the same for
the FreeBSD build system and the portable
libtool/autoconf/automake build system.
link names, usernames, or group names that contain
non-ASCII characters.
In particular, this corrects an inconsistency reported
by Ed Maste when archiving symlinks with odd characters:
long symlinks would get preserved, short ones would
be changed.
broken assignment to floats (e.g., i386 with gcc -O, but not amd64 or
ia64; i386 with gcc -O0 worked accidentally).
Use an unnamed volatile temporary variable to trick gcc -O into clipping
extra precision on assignment. It's surprising that only 1 place needed
to be changed.
For tanf() on i386 with gcc -O, the bug caused errors > 1 ulp with a
density of 2.3% for args larger in magnitude than 128*pi/2, with a
maximum error of 1.624 ulps.
After this fix, exhaustive testing shows that range reduction for
floats works as intended assuming that it is in within a factor of
about 2^16 of working as intended for doubles. It provides >= 8
extra bits of precision for all ranges. On i386:
range max error in double/single ulps extra precision
----- ------------------------------- ---------------
0 to 3*pi/4 0x000d3132 / 0.0016 9+ bits
3*pi/4 to 128*pi/2 0x00160445 / 0.0027 8+
128*pi/2 to +Inf 0x00000030 / 0.00000009 23+
128*pi/2 up, -O0 before fix 0x00000030 / 0.00000009 23+
128*pi/2 up, -O1 before fix 0x10000000 / 0.5 1
The 23+ bits of extra precision for large multiples corresponds to almost
perfect reduction to a pair of floats (24 extra would be perfect).
After this fix, the maximum relative error (relative to the corresponding
fdlibm double precision function) is < 1 ulp for all basic trig functions
on all 2^32 float args on all machines tested:
amd64 ia64 i386-O0 i386-O1
------ ------ ------ ------
cosf: 0.8681 0.8681 0.7927 0.5650
sinf: 0.8733 0.8610 0.7849 0.5651
tanf: 0.9708 0.9329 0.9329 0.7035
of pi/2 (1 line) and expand a comment about related magic (many lines).
The bug was essentially the same as for the +-pi/2 case (a mistranslated
mask), but was smaller so it only significantly affected multiples
starting near +-13*pi/2. At least on amd64, for cosf() on all 2^32
float args, the bug caused 128 errors of >= 1 ulp, with a maximum error
of 1.2393 ulps.
and add a comment about related magic (many lines)).
__kernel_cos[f]() needs a trick to reduce the error to below 1 ulp
when |x| >= 0.3 for the range-reduced x. Modulo other bugs, naive
code that doesn't use the trick would have an error of >= 1 ulp
in about 0.00006% of cases when |x| >= 0.3 for the unreduced x,
with a maximum relative error of about 1.03 ulps. Mistransation
of the trick from the double precision case resulted in errors in
about 0.2% of cases, with a maximum relative error of about 1.3 ulps.
The mistranslation involved not doing implicit masking of the 32-bit
float word corresponding to to implicit masking of the lower 32-bit
double word by clearing it.
sinf() uses __kernel_cosf() for half of all cases so its errors from
this bug are similar. tanf() is not affected.
The error bounds in the above and in my other recent commit messages
are for amd64. Extra precision for floats on i386's accidentally masks
this bug, but only if k_cosf.c is compiled with -O. Although the extra
precision helps here, this is accidental and depends on longstanding
gcc precision bugs (not clipping extra precision on assignment...),
and the gcc bugs are mostly avoided by compiling without -O. I now
develop libm mainly on amd64 systems to simplify error detection and
debugging.
17+17+24 bit pi/2 must only be used when subtraction of the first 2
terms in it from the arg is exact. This happens iff the the arg in
bits is one of the 2**17[-1] values on each side of (float)(pi/2).
Revert to the algorithm in rev.1.7 and only fix its threshold for using
the 3-term pi/2. Use the threshold that maximizes the number of values
for which the 3-term pi/2 is used, subject to not changing the algorithm
for comparing with the threshold. The 3-term pi/2 ends up being used
for about half of its usable range (about 64K values on each side).
a maximum error of 2.905 ulps for cosf(), but the algorithm for cosf()
is good for < 1 ulps and happens to give perfect rounding (< 0.5 ulps)
near +-pi/2 except for the bug. The extra relative errors for tanf()
were similar (slightly larger). The bug didn't affect sinf() since
sinf'(+-pi/2) is 0.
For range reduction in ~[-3pi/4, -pi/4] and ~[pi/4, 3pi/4] we must
subtract +-pi/2 and the only complication is that this must be done
in extra precision. We have handy 17+24-bit and 17+17+24-bit
approximations to pi/2. If we always used the former then we would
lose up to 24 bits of accuracy due to cancelation of leading bits, but
we need to keep at least 24 bits plus a guard digit or 2, and should
keep as many guard bits as efficiency permits. So we used the
less-precise pi/2 not very near +-pi/2 and switched to using the
more-precise pi/2 very near +-pi/2. However, we got the threshold for
the switch wrong by allowing 19 bits to cancel, so we ended up with
only 21 or 22 bits of accuracy in some cases, which is even worse than
naively subtracting pi/2 would have done.
Exhaustive checking shows that allowing only 17 bits to cancel (min.
accuracy ~24 bits) is sufficient to reduce the maximum error for cosf()
near +-pi/2 to 0.726 ulps, but allowing only 6 bits to cancel (min.
accuracy ~35-bits) happens to give perfect rounding for cosf() at
little extra cost so we prefer that.
We actually (in effect) allow 0 bits to cancel and always use the
17+17+24-bit pi/2 (min. accuracy ~41 bits). This is simpler and
probably always more efficient too. Classifying args to avoid using
this pi/2 when it is not needed takes several extra integer operations
and a branch, but just using it takes only 1 FP operation.
The patch also fixes misspelling of 17 as 24 in many comments.
For the double-precision version, the magic numbers include 33+53 bits
for the less-precise pi/2 and (53-32-1 = 20) bits being allowed to
cancel, so there are ~33-20 = 13 guard bits. This is sufficient except
probably for perfect rounding. The more-precise pi/2 has 33+33+53
bits and we still waste time classifying args to avoid using it.
The bug is apparently from mistranslation of the magic 32 in 53-32-1.
The number of bits allowed to cancel is not critical and we use 32 for
double precision because it allows efficient classification using a
32-bit comparison. For float precision, we must use an explicit mask,
and there are fewer bits so there is less margin for error in their
allocation. The 32 got reduced to 4 but should have been reduced
almost in proportion to the reduction of mantissa bits.
in 1993 in rev.1.5 of the i386 a.out version (csu/i386/crt0.c).
Profiling uses a magic label "eprol" to delimit the start of the part
of the text section covered by profiling. This label must be placed
before the call to main() to get main() properly profiled. It was
placed there in rev.1.1 of crt0.c. Rev.1.5 imported the initial
implementation of shared libraries in FreeBSD and misplaced the label.
Fortunately, the misplaced label was misspelled and the old label
wasn't removed, so the new label had no effect. Unfortunately, when
profiling was implemented for the ELF in 1998 in rev.1.2 of
csu/i386-elf/crt1.c, only the incorrectly placed label was copied
(after fixing its name). The bug was then copied to all other arches.
The label seems to be still misplaced in NetBSD for most arches. It
is in common.c for most arches so it is even further from being inside
the function that calls main().
I think "eprol" is short for "end of prologue", but it must be placed
before the end of the prologue so that it covers main(). crt0.c has
it before the calls atexit(_mcleanup) and monstartup(...), but it
cannot affect these calls so I moved it after the call to monstartup().
It now also covers the call to _init() but not the newer call to
_init_tls(). Profiling of _init() seems to be harmless, and the call
to _init_tls() seems to be misplaced.
Reviewed by: jdp (long ago, for a slightly different i386 version)
host name. This is matches the documented behaviro. The previous
behavior would remove the domain name even if the result retained a dot.
This fixes rsh connections from a.example.com to example.com.
Reviewed by: ceri (at least the concept)
o Don't reinitialise the atfork() handler list in the child. We
are meant to call the child handler, and on subsequent fork()s
should call all three functions as normal.
o Don't reinitialise the thread specific keyed data in the
child after a fork. Applications may require this for context.
o Reinitialise curthread->tlflags after removing ourselves from
(and reinitialising) the various internal thread lists.
o Reinitialise __malloc_lock in the child after fork() (to balance
our explicitly taking the lock prior to the fork()).
With these changes, it is possible to enable the NOTYET code in
thr_kern.c to allow the use of non-async-safe functions after
fork()ing from a threaded program.
Reviewed by: Daniel Eischen <deischen@freebsd.org>
[_malloc_lock reinitialisation has since been moved to avoid polluting the
!NOTYET code]
"HEADER" unless the open is successful. Instead, leave the state as
"NEW." In particular, if archive_read_open() fails, a subsequent call
to archive_read_next_header() will now cause an explicit assertion
failure instead of a silent segmentation fault.
This may need a little more work to fully realize the intention: If
archive_read_open() fails, you should be able to call it again on the
same archive handle to open a different archive (or the same archive
using a different mechanism).
sizeof(*list), not sizeof(**list). (i.e., sizeof(pointer) rather than
sizeof(char)).
It is possible that this buffer overflow is exploitable, but it was
added after RELENG_5 forked and hasn't been MFCed, so this will not
receive an advisory.
Submitted by: Vitezslav Novy
MFC after: 1 day
to doubles as bits. fdlibm-1.1 had similar aliasing bugs, but these
were fixed by NetBSD or Cygnus before a modified version of fdlibm was
imported in 1994. TRUNC() is only used by tgamma() and some
implementation-detail functions. The aliasing bugs were detected by
compiling with gcc -O2 but don't seem to have broken tgamma() on i386's
or amd64's. They broke my modified version of tgamma().
Moved the definition of TRUNC() to mathimpl.h so that it can be fixed
in one place, although the general version is even slower than necessary
because it has to operate on pointers to volatiles to handle its arg
sometimes being volatile. Inefficiency of the fdlibm macros slows
down libm generally, and tgamma() is a relatively unimportant part of
libm. The macros act as if on 32-bit words in memory, so they are
hard to optimize to direct actions on 64-bit double registers for
(non-i386) machines where this is possible. The optimization is too
hard for gcc on amd64's, and declaring variables as volatile makes it
impossible.
Change first MAXPATHLEN to more standard PATH_MAX
Change second MAXPATHLEN to 1024 (it is temp buffer not related)
Change comment to reflect that.
Suggested by: bde
just use MAXPATHLEN. It prevents potential buffer overflow with other
malloc implementations.
(this change based on submitted patch)
PR: 86135
Submitted by: Trevor Blackwell <tlb@tlb.org>
(wchar_t is defined in stddef.h, and only two files need more than that.)
Portability: Since the wchar requirements are really quite modest,
it's easy to define basic replacements for wcslen, wcscmp, wcscpy,
etc, for use on systems that lack <wchar.h>. In particular, this allows
libarchive to be used on older OpenBSD systems.
than the value of backlog argument.
- Document the fact that a subsequent listen(2) calls on the listening
socket change the backlog argument.
- Note that current listen queue lengths can be queried using netstat(1).
Submitted by: Igor Sysoev <is rambler-co.ru>
Wording by: gnn
It is the binary equivalent to strstr(3).
void *memmem(const void *big, size_t big_len,
const void *little, size_t little_len);
Submitted by: Pascal Gloor <pascal.gloor at spale.com>
MFC after: 3 days
correctly in the case of FTP_PROXY, because an empty FTP_PROXY has a
specific meaning ("don't use any proxy at all for ftp, even if HTTP_PROXY
is defined"), while an empty HTTP_PROXY has no meaning at all.
PR: bin/85185
Submitted by: Conall O'Brien <conallob=freebsd@maths.tcd.ie>
MFC after: 2 weeks
example in libmemstat.3 was not updated to take this rename into account.
Update the example.
PR: 84946
Submitted by: Wojciech A. Koszek <dunstan at freebsd dot czest dot pl>
MFC after: 1 day
inadvertently match a negative char in the RE being compiled.
This fixes compilation of "\376" (as an ERE) and "\376\376" (as a BRE).
PR: 84740
MFC after: 1 week
tokenizer.c:1.3). Contrary to the commit log there were no memory leaks,
but the change introduced a bug because the free'd pointer was not zeroed
and calling the appropriate _end() function would call free() a second time.
so that libmemstat can be used to view full memory statistics from
kernel core dumps and /dev/mem. This is provided via a new query
function, memstat_kvm_malloc(), which is also automatically invoked
by memstat_kvm_all(). A kvm handle must be passed in.
This will allow malloc(9)-specific code to be removed from vmstat(8).
opt_vmpage.h.
Remove definition of _KERNEL, it is no longer required in order to
include uma_int.h, as the sensitive parts of uma_int.h (a number of
inlines depending on kernel-only constants) are now protected by
_KERNEL.
extracted from tar archives. Otherwise, converting tar archives to
cpio format (with "bsdtar -cf out.cpio @in.tar") convert every entry
into a hard link to a single file. This simple logic breaks hard
links, but that's better than the alternative.
MFC after: 7 days
header of the pax extension entry, clip them to ustar limits. In particular,
this prevents an internal panic for very old files.
Thanks to: Chris Spiegel
MFC after: 7 days
GNU tar sparse files, people have extended cpio) and clarify an
important detail about pax format (that ustar-compliant archivers
can mostly read pax archives correctly).
MFC after: 7 days
that knows how to extract UMA(9) allocator statistics from a core dump or
live memory image using kvm(3). The caller is expected to provide the
necessary kvm_t handle, which is then used by libmemstat(3).
With these changes, it is trivially straight forward to re-introduce
vmstat -z support on core dumps, which was lost when UMA was introduced.
In the short term, this requires including vm/ include files that are not
intended for extra-kernel use, requiring in turn some ugliness.
- Move memory_type_list flushing logic from memstat_mtl_free() to
_memstat_mtl_empty(), a libmemstat-internal function that can
be called from other parts of the library. Invoke
_memstat_mtl_empty() from memstat_mtl_free(), which also frees
the containing list structure.
Invoke _memstat_mtl_empty() instead of memstat_mtl_free() in
various error cases in memstat_malloc.c and memstat_uma.c, which
previously resulted in the list being freed prematurely.
- Reverse the order of updating the mt_kegfree and mt_free fields
of the memory_type in memstat_uma.c, otherwise keg free items
won't be counted properly for non-secondary zones.
MFC after: 3 days
conversion routine, now change my mind and add one, memstat_strerror(3),
which returns a const char * pointer to a string describing the error,
to be used on the results of memstat_mtl_geterror().
While here, also correct a minor typo in the HISTORY man page.
Pointers on improving ease of internationalization would be
appreciated.
MFC after: 1 day
- Define a set of libmemstat(3) error constants, which are used by all
libmemstat(3) methods except for memstat_mtl_alloc(), which allocates
a memory type list and may return ENOMEM via errno.
- Define a per-memory_type_list current error value, which is set when a
call associated with a memory list fails. This requires wrapping a
structure around the queue(9) list head data structure, but this change
is not visible to libmemstat(3) consumers due to using access methods.
- Add a new accessor method, memstat_mtl_geterror() to retrieve the error
number.
- Consistently set the error number in a number of failure modes where
previously some combination of setting errno and printf'ing error
descriptions was used. libmemstat(3) will now no longer print to stdio
under any circumstances. Returns of NULL/-1 for errors remain the
same.
This avoids use of stdio, misuse of error numbers, and should make it
easier to program a libmemstat(3) consumer able to print useful error
messages. Currently, no error-to-string function is provided, as I'm
unsure how to address internationalization concerns.
MFC after: 1 day
try and discourage use outside the library.
Remove duplicate declaration of memstat_mtl_free() from memstat_internal.h,
as it's not internal, and the memstat.h definition suffices.
on top of a primary zone, sharing the same allocation "keg". When
reporting statistics for zones, do not report the free items in the
keg as part of the free items in the zone, or those free items will
be reported more than once: for the primary zone, and then any
secondary zones off the primary zone. Separately record and maintain
a kegfree statistic, and export via memstat_get_kegfree(), which is
available for use if needed. Since items free'd back to the keg are
not fully initialized, and hence may not actually be available (since
secondary zone ctor-time initialization can fail), this makes some
amount of sense.
This change corrects a bug made visible in the libmemstat(3)
modifications to netstat: mbufs freed back to the keg from the
packet zone would be counted twice, resulting in negative values
being printed in the mbuf free count.
Some further refinement of reporting relating to secondary zones may
still be required.
Reported by: ssouhlal
MFC after: 3 days
