that piggybacks on bce_tick() callout.
- Instead of unconditionally resetting the controller, try to
skip the reset in case we got a pause frame, like em(4) did.
- Lock bce_tick() using callout_init_mtx().
Discussed with/Reviewed by: glebius, scottl, davidch
not needed if the proper ordering is done in attach and shutdown.
Remove usage of if_timer/watchdog and roll my own by piggybacking
off the tick() function.
Use the new usb system to allocate task queues instead of using
the system wide thread for taskqueues.
for usb. I hope that this will eventually be used for generic devices
that need full fledged blocking threads for event processing.
Create a taskqueue:
void usb_ether_task_init(device_t, int, struct usb_taskqueue *);
Enqueue a task:
void usb_ether_task_enqueue(struct usb_taskqueue *, struct task *);
Wait for all tasks queued to complete:
void usb_ether_task_drain(struct usb_taskqueue *, struct task *);
Destroy the taskqueue:
void usb_ether_task_destroy(struct usb_taskqueue *);
link state changes. Instead, build new speed/duplex/flow-control
settings from the values reported from PHY.
This should fix speed/duplex/flow-control mismatches between GMAC and
PHY which resulted in very poor Rx performance due to lots of
out-of-order packet delivery.
Reported by: Arno J. Klaassen <arno AT heho DOT snv DOT jussieu DOT fr>
Tested by: Arno J. Klaassen <arno AT heho DOT snv DOT jussieu DOT fr>
modern dual-core systems as well.
- Parse the _CST packages for each cpu and track all the states individually,
on a per-cpu basis.
- Revert to generic FADT/P_BLK based Cx control if the _CST package
is not present on all cpus. In that case, the new driver will
still support per-cpu Cx state handling. The driver will determine the
highest Cx level that can be supported by all the cpus and configure the
available Cx state based on that.
- Fixed the case where multiple cpus in the system share the same
registers for Cx state handling. To do that, added a new flag
parameter to the acpi_PkgGas and acpi_bus_alloc_gas functions that
enable the caller to add the RF_SHAREABLE flag. This flag could also be
useful to other callers (acpi_throttle?) in the tree but this change is
not yet made.
- For Core Duo cpus, both cores seems to be taken out of C3 state when
any one of the cores need to transition out. This broke the short sleep
detection logic. It is disabled now if there is more than one cpu in
the system for now as it fixed it in my case. This quirk may need to
be re-enabled later differently.
- Added support to control cx_lowest on a per-cpu basis. There is still
a generic cx_lowest to enable changing cx_lowest for all cpus with a single
sysctl and for ease of use. Sample output for the new sysctl:
dev.cpu.0.cx_supported: C1/1 C2/1 C3/57
dev.cpu.0.cx_lowest: C3
dev.cpu.0.cx_usage: 0.00% 43.16% 56.83%
dev.cpu.1.cx_supported: C1/1 C2/1 C3/57
dev.cpu.1.cx_lowest: C3
dev.cpu.1.cx_usage: 0.00% 45.65% 54.34%
hw.acpi.cpu.cx_lowest: C3
This work was done by Stephane E. Potvin with some simple reworking by
myself. Thank you.
Submitted by: Stephane E. Potvin <sepotvin / videotron.ca>
MFC after: 2 weeks
revision 1.98 is NOT merged, because FreeBSD does not support this
syntax.
revision 1.99 is NOT merged, "const poisoning" part is not applicable
to FreeBSD. There is no variable shadowing, GCC can't find
this one (but there are others)
revision 1.100 is NOT merged, because it was null patch (no changes)
revision 1.101 is NOT merged, there is no BIT() macro in FreeBSD
revision 1.102 is merged
revision 1.103 is partially merged. There is no ai.ifaceh in FreeBSD
revision 1.104 is NOT merged
revision 1.105 is merged
revision 1.106 is not merged, because of rev. 1.107
revision 1.107 is a backuout of 1.106
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
---snip---
New features:
1. Optional multichannel recording (32 channels on Live!, 64 channels
on Audigy).
All channels are 16bit/48000Hz/mono, format is fixed.
Half of them are copied from sound output, another half can be
used to record any data from DSP. What should be recorded is
hardcoded in DSP code. In this version it records dummy data, but
can be used to record all DSP inputs, for example..
Because there are no support of more-than-stereo sound streams
multichannell stream is presented as one 32(64)*48000 Hz 16bit mono
stream.
Channel map:
SB Live! (4.0/5.1)
offset (words) substream
0x00 Front L
0x01 Front R
0x02 Digital Front L
0x03 Digital Front R
0x04 Digital Center
0x05 Digital Sub
0x06 Headphones L
0x07 Headphones R
0x08 Rear L
0x09 Rear R
0x0A ADC (multi-rate recording) L
0x0B ADC (multi-rate recording) R
0x0C unused
0x0D unused
0x0E unused
0x0F unused
0x10 Analog Center (Live! 5.1) / dummy (Live! 4.0)
0x11 Analog Sub (Live! 5.1) / dummy (Live! 4.0)
0x12..-0x1F dummy
Audigy / Audigy 2 / Audigy 2 Value / Audigy 4
offset (words) substream
0x00 Digital Front L
0x01 Digital Front R
0x02 Digital Center
0x03 Digital Sub
0x04 Digital Side L (7.1 cards) / Headphones L (5.1 cards)
0x05 Digital Side R (7.1 cards) / Headphones R (5.1 cards)
0x06 Digital Rear L
0x07 Digital Rear R
0x08 Front L
0x09 Front R
0x0A Center
0x0B Sub
0x0C Side L
0x0D Side R
0x0E Rear L
0x0F Rear R
0x10 output to AC97 input L (muted)
0x11 output to AC97 input R (muted)
0x12 unused
0x13 unused
0x14 unused
0x15 unused
0x16 ADC (multi-rate recording) L
0x17 ADC (multi-rate recording) R
0x18 unused
0x19 unused
0x1A unused
0x1B unused
0x1C unused
0x1D unused
0x1E unused
0x1F unused
0x20..0x3F dummy
Fixes:
1. Do not assign negative values to variables used to index emu_cards
array. This array was never accessed when index is negative, but
Alexander (netchild@) told me that Coverity does not like it.
After this change emu_cards[0] should never be used to identify
valid sound card.
2. Fix off-by-one errors in interrupt manager. Add more checks there.
3. Fixes to sound buffering code now allows driver to use large playback
buffers.
4. Fix memory allocation bug when multichannel recording is not
enabled.
5. Fix interrupt timeout when recording with low bitrate (8kHz).
Hardware:
1. Add one more known Audigy ZS card to list. Add two cards with
PCI IDs betwen old known cards and new one.
Other changes:
1. Do not use ALL CAPS in messages.
Incomplete code:
1. Automute S/PDIF when S/PDIF signal is lost.
Tested on i386 only, gcc 3.4.6 & gcc41/gcc42 (syntax only).
---snip---
This commits enables a little bit of debugging output when the driver is
loaded as a module. I did a cross-build test for amd64.
The code has some style issues, this will be addressed later.
The multichannel recording part is some work in progress to allow playing
around with it until the generic sound code is better able to handle
multichannel streams.
This is supposed to fix
CID: 171187
Found by: Coverity Prevent
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
server.
Don't complain about a hard loop id of 0xffff- we get this in
point-to-point topologies with the 2300 and 2K Login firmware.
Up the timeout on register FC4 types commands.
- Rename confusing AGP_INTEL_I845_MCHCFG to AGP_INTEL_I845_AGPM.
- Move E7205 and E7505 from i8x5 to i8x0 family. It probably worked
because the actual offset is the same.
In fact, all three families have the bit at the exact same place. Only
differences are name and width of the registers, i.e., NBXCFG (0x50, dword),
RDCR (0x51, byte), AGPM (0x51, byte), MCHCFG (0x50, word) depending on
the family of the chipsets.
a spin mutex since it doesn't have an INTR_FAST interrupt handler.
Beyond that the driver is still under Giant anyway.
- Remove unneeded locking during attach across operations that can't be
called with locks held (such as bus_dma_tag_create()).
MFC after: 1 week
Not objected to by: scottl
start working with third party usb modules, where sometimes it
is not easy to set the inclusion order so that there are no multiple
inclusions, yet you want to compile with high WARNS levels).
I am not sure if there is a standard for having a leading and/or trailing _
in the macro name, the usb code seems to use both.
There are still several unprotected headers here so it might be useful
to do the same thing on other files as well as the need arises.
MFC After: 3 days
semantics.
- Stop testing bpf pointers for NULL. In some cases use
bpf_peers_present() and then call the function directly inside the
conditional block instead of the macro.
- For places where the entire conditional block is the macro, remove the
test and make the macro unconditional.
- Use BPF_MTAP() in if_pfsync on FreeBSD instead of an expanded version of
the old semantics.
Reviewed by: csjp (older version)
o change handling of regdomain-related mib knobs so they can be set
post-attach: regdomain, countrycode, outdoor, and xchanmode; the
hal will not permit changing the regdomain but we expose it for now
o on regdomain/countrycode change recalculate the channel list and
push it to the net80211 layer (NB: looks to need more tweaking)
o setup rate tables for half/quarter rate channels
o honor half/quarter rate channel configs when changing channels
o honor half/quarter rate channel configs when setting the slot time
o use hack/nonstandard channel numbering scheme for the public safety
band to avoid overlapping 2.4G channels on dual-band cards
o remove setup of ic_sup_rates; the net80211 layer can do this for us
and it simplifies handling of half/quarter rate channels
Tested only in Public Safety Band with cards that have RF5112.
bge_intr(). Some of them are used in bge_poll(). Simplify by only
initializing these for polling mode and not toggling them when switching
modes. This also fixes missing synchronization with the coalescing
engine in the toggling.
The problem was that I was acquiring the driver sx lock and then waiting
for a taskqueue to drain, however the taskqueue itself would try to
acquire the lock as well leading to a deadlock.
To fix the problem roll my own exclusive lock that allows for lock
cancellation. This is a normal exclusive lock, however if someone
marks it as "dead" then all waiters who request an error return will
get back an error instead of continuing to wait for the lock.
In this particular case, the shutdown and detach functions kill the
lock while the async task thread tries to acquire the lock but will
abort if the lock returns an error.
The other option was to drop the driver lock mid-detach and mid-shutdown,
mid-detach was a ok, however mid-shutdown was not.
While I'm here, fix a bug in what appears to be the mii link status
word in the softc going out to lunch. Explicitly set the status
word to 1 after initializing the mii. This would result in an interface
that would never respond to "if_start" requests as the mii interface
would always look down.
