Fix section pattern code to exclude .rel.data.* sections from being
merged into .data. Otherwise relocations in those sections are lost
in final binary
Reviewed by: andrew
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9108
__bss_end should not be included in .bss zeroing code. Otherwise first 4
bytes of the section that follows .bss (in loader's case it's .sdata) are
overwritten by zero.
Reviewed by: andrew
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9108
In-tree objdump is too old to dump new ELF headers. But for example if we
use: `make CROSS_TOOLCHAIN=riscv64-gcc TARGET_ARCH=riscv64` and do not specify
CROSS_BINUTILS_PREFIX in env, embed_mfs.sh cannot find the correct objdump.
This patch just replaces using of objdump with elfdump to collect needed
information.
Later we may also put an ELFDUMP in CROSSENV and use it in embed_mfs.sh .
Reviewed by: emaste, br
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9062
a linuxkpi style device is expected. If OFED/linuxkpi actually starts
using this field then we'll have to figure out whether to create fake
devices for these drivers or have linuxkpi deal with NULL device.
This mismatch was first reported as part of D6585.
Unnecessary prefetch just loads HW prefetcher and displaces other
cache entries (which could be really useful).
If we parse mbuf for TSO early and use firmware-assisted TSO, we do not
expect mbuf data access when we compose firmware-assisted TSO (v1 or v2)
option descriptors. If packet header needs to be linearized or finally
FATSO cannot be used because of, for example, too big header, we do not
care about a bit more performance degradation because of prefetch
absence (it is better to optimize more common case).
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9120
in some arm64 hardware, for example the AMD Opteron A1100.
Reviewed by: mav
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8852
This is needed for two reasons:
* Drivers will need to know what the negotiated set of VHT capabilities
and rates are in order to configure (and reconfigure for opmode/chanwidth
changes) how to speak to a given peer; and
* Because some vendors are "special", we should be careful in what we announce
to them during peer association.
This isn't the complete solution, as I still need to make sure that when
sending out probe requests before we know what we want, we don't limit
the capabilities being announced. This is important for IBSS/mesh work
later on as probe request/response exchanges are the first hint at what
a peer supports. I'll look at adding that to the API soon.
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
These have been tested back-to-back with Linux 3.x and a similar attachment
at the other end; a CDC EEM-like encapsulation can be used for emulated
Ethernet over udbp(4) with ng_ether.
potentially leading to fatal unaligned accesses on architectures with
strict alignment requirements. This change fixes dummynet(4) as far
as accesses to 64-bit members of struct dn_* are concerned, tripping
up on sparc64 with accesses to 32-bit members happening to be correctly
aligned there. In other words, this only fixes the tip of the iceberg;
larger parts of dummynet(4) still need to be rewritten in order to
properly work on all of !x86.
In principle, considering the amount of code in dummynet(4) that needs
this erroneous pattern corrected, an acceptable workaround would be to
declare all struct dn_* packed, forcing compilers to do byte-accesses
as a side-effect. However, given that the structs in question aren't
laid out well either, this would break ABI/KBI.
While at it, replace all existing bcopy(9) calls with memcpy(9) for
performance reasons, as there is no need to check for overlap in these
cases.
PR: 189219
MFC after: 5 days
If some process' nodes were accessed using procfs and the process
cannot exit properly at the time modunload event is reported to the
pseudofs-backed filesystem, the assertion in pfs_vncache_unload() is
triggered. Assertion is correct, the cache should be cleaned.
Approved by: des (pseudofs maintainer)
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Instead of collecting statistics for each combination of ports and logical
units, that consumed ~45KB per LU with present number of ports, collect
separate statistics for every port and every logical unit separately, that
consume only 176 bytes per each single LU/port. This reduces struct
ctl_lun size down to just 6KB.
Also new IOCTL API/ABI does not hardcode number of LUs/ports, and should
allow handling of very large quantities.
MFC after: 2 weeks (probably keeping old API enabled for some time)
handler which already holds the mutex, and have sdhci_handle_card_present()
be just a tiny wrapper that does the locking for external callers.
This should fix the recursive locking panics seen on rpi3.
Reported by: Shawn Webb
Besides slots always having non-removable media, these HCIs require
a custom hardware reset sequence after power-up.
- Flesh out the support for Intel Braswell eMMC controllers further.
Apart from also requiring said reset code, the timeout clock needs to
be hardcoded to 1 MHz for these.
Both the special reset and timeout clock handlings are implemented as
global sdhci(4) quirks as the same treatment will be necessary for
Intel eMMC controllers attached via ACPI (once sdhci(4) grows such a
front-end).
- In sdhci_init_slot(), use the right capability field for determining
the announced bus width based on MMC_CAP_*_BIT_DATA.
- Correct inverted sdhci_pci_softc member comments added in r276469. [1]
Submitted by: Anton Yuzhaninov [1]
MFC after: 5 days
or write, resulting in random short-read and short-write returns for
requests. Fixing this fixes nominal block I/O via mmcsd(4).
Obtained from: DragonFlyBSD (fd4b97583be1a1e57234713c25f6e81bc0411cb0)
MFC after: 5 days
This array takes 64KB of RAM now, that was more then half of struct ctl_lun
size. If at some point we support more ports, this may need another tune.
MFC after: 2 weeks
card presence and write protect switch detection.
A bridge driver just needs to call the setup routine in its attach(), the
teardown in its detach(), and write a couple tiny glue functions to connect
the sdhci interface functions to the new helper functions. This is not
extensively documented, but multiple examples will exist real soon.
card insert/remove events on controllers that don't implement the insert
and remove interrupts.
Bridge drivers can set a new slot option, SDHCI_NON_REMOVABLE, to indicate
non-removable media (such as eMMC). The sdhci driver will not enable
insert/remove interrupts, and sdhci_generic_get_card_present() will always
return true.
Bridge drivers can set a new quirk, SDHCI_QUIRK_POLL_CARD_PRESENT, and the
sdhci driver will not enable insert/remove interrupts, and instead will use
a callout to poll the card-present status at 5 Hz.
For bridge drivers that get notified of card insert/remove via gpio
interrupts, there is a new sdhci_handle_card_present() function they can
call from the gpio interrupt handler to inform the sdhci code of the event.
In addition to adding these new features, the existing code to debounce card
insertions was updated to use taskqueue_enqueue_timeout() instead of
scheduling a callout to do the taskqueue_enqueue(). There is also now a
comment explaining that insertion-debounce is what's going on -- it took me
a long time to realize that's what the old sdhci_card_delay() routine was
really doing. There is no functional difference between the old and new
debounce code (I hope!).
Use device-specific Rx buffer size to ensure that data will not be
truncated + add a warning if truncation was detected (the driver
cannot handle this case correctly yet).
Tested with:
- RTL8188CUS, RTL8188EU and RTL8821AU, STA / AP modes.
There are places where checks are made against VM_MAX_KERNEL_ADDRESS, or
virtual_end (set to VM_MAX_KERNEL_ADDRESS). With 32-bit checks, an address will
always be less than or equal to 0xffffffff. Drop a page, so those checks can
terminate loops safely.
