sysctl, net.inet.ip.fw.permanent_rules.
This allows you to install rules that are persistent across flushes,
which is very useful if you want a default set of rules that
maintains your access to remote machines while you're reconfiguring
the other rules.
Reviewed by: Mark Murray <markm@FreeBSD.org>
When we recieve a fragmented TCP packet (other than the first) we can't
extract header information (we don't have state to reference). In a rather
unelegant fashion we just move on and assume a non-match.
Recent additions to the TCP header-specific section of the code neglected
to add the logic to the fragment code so in those cases the match was
assumed to be positive and those parts of the rule (which should have
resulted in a non-match/continue) were instead skipped (which means
the processing of the rule continued even though it had already not
matched).
Fault can be spread out over Rich Steenbergen (tcpoptions) and myself
(tcp{seq,ack,win}).
rwatson sent me a patch that got me thinking about this whole situation
(but what I'm committing / this description is mine so don't blame him).
address is configured on a interface. This is useful for routers with
dynamic interfaces. It is now possible to say:
0100 allow tcp from any to any established
0200 skipto 1000 tcp from any to any
0300 allow ip from any to any
1000 allow tcp from 1.2.3.4 to me 22
1010 deny tcp from any to me 22
1020 allow tcp from any to any
and not have to worry about the behaviour if dynamic interfaces configure
new IP numbers later on.
The check is semi expensive (traverses the interface address list)
so it should be protected as in the above example if high performance
is a requirement.
reserved and now allocated TCP flags in incoming packets. This patch
stops overloading those bits in the IP firewall rules, and moves
colliding flags to a seperate field, ipflg. The IPFW userland
management tool, ipfw(8), is updated to reflect this change. New TCP
flags related to ECN are now included in tcp.h for reference, although
we don't currently implement TCP+ECN.
o To use this fix without completely rebuilding, it is sufficient to copy
ip_fw.h and tcp.h into your appropriate include directory, then rebuild
the ipfw kernel module, and ipfw tool, and install both. Note that a
mismatch between module and userland tool will result in incorrect
installation of firewall rules that may have unexpected effects. This
is an MFC candidate, following shakedown. This bug does not appear
to affect ipfilter.
Reviewed by: security-officer, billf
Reported by: Aragon Gouveia <aragon@phat.za.net>
of IP datagram. This fixes the problem when firewall denied fragmented
packets whose last fragment was less than minimum protocol header size.
Found by: Harti Brandt <brandt@fokus.gmd.de>
PR: kern/22309
enough into the mbuf data area. Solve this problem once and for all
by pulling up the entire (standard) header for TCP and UDP, and four
bytes of header for ICMP (enough for type, code and cksum fields).
the IP_FW_IF_IPID rule. (We have recently decided to keep the
ip_id field in network byte order inside the kernel, see revision
1.140 of src/sys/netinet/ip_input.c).
I did not like to have the conversion happen in userland, and I
think that the similar conversions for fw_tcp(seq|ack|win) should
be moved out of userland (src/sbin/ipfw/ipfw.c) into the kernel.
for them does not belong in the IP_FW_F_COMMAND switch, that mask doesn't even
apply to them(!).
2. You cannot add a uid/gid rule to something that isn't TCP, UDP, or IP.
XXX - this should be handled in ipfw(8) as well (for more diagnostic output),
but this at least protects bogus rules from being added.
Pointy hat: green
It also squashes 99% of packet kiddie synflood orgies. For example, to
rate syn packets without MSS,
ipfw pipe 10 config 56Kbit/s queue 10Packets
ipfw add pipe 10 tcp from any to any in setup tcpoptions !mss
Submitted by: Richard A. Steenbergen <ras@e-gerbil.net>
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
packet divert at kernel for IPv6/IPv4 translater daemon
This includes queue related patch submitted by jburkhol@home.com.
Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
- Implement 'ipfw tee' (finally)
- Divert packets by calling new function divert_packet() directly instead
of going through protosw[].
- Replace kludgey global variable 'ip_divert_port' with a function parameter
to divert_packet()
- Replace kludgey global variable 'frag_divert_port' with a function parameter
to ip_reass()
- style(9) fixes
Reviewed by: julian, green
Make a sonewconn3() which takes an extra argument (proc) so new sockets created
with sonewconn() from a user's system call get the correct credentials, not
just the parent's credentials.
using syslog(3) (log(9)) for its various purposes! This long-awaited
change also includes such nice things as:
* macros expanding into _two_ comma-delimited arguments!
* snprintf!
* more snprintf!
* linting and criticism by more people than you can shake a stick at!
* a slightly more uniform message style than before!
and last but not least
* no less than 5 rewrites!
Reviewed by: committers
with a match probability to achieve non-deterministic behaviour of
the firewall. This can be extremely useful for testing purposes
such as simulating random packet drop without having to use dummynet
(which already does the same thing), and simulating multipath effects
and the associated out-of-order delivery (this time in conjunction
with dummynet).
The overhead on normal rules is just one comparison with 0.
Since it would have been trivial to implement this by just adding
a field to the ip_fw structure, I decided to do it in a
backward-compatible way (i.e. struct ip_fw is unchanged, and as a
consequence you don't need to recompile ipfw if you don't want to
use this feature), since this was also useful for -STABLE.
When, at some point, someone decides to change struct ip_fw, please
add a length field and a version number at the beginning, so userland
apps can keep working even if they are out of sync with the kernel.
_or_ you may specify "log logamount number" to set logging specifically
the rule.
In addition, "ipfw resetlog" has been added, which will reset the
logging counters on any/all rule(s). ipfw resetlog does not affect
the packet/byte counters (as ipfw reset does), and is the only "set"
command that can be run at securelevel >= 3.
This should address complaints about not being able to set logging
amounts, not being able to restart logging at a high securelevel,
and not being able to just reset logging without resetting all of the
counters in a rule.
