date: 2002/12/10 14:07:37; author: toshii; state: Exp; lines: +6 -6
Add a couple of le32toh which were missing in the previous.
Pointed out by SOMEYA Yoshihiko.
date: 2002/12/07 07:33:20; author: toshii; state: Exp; lines: +50 -29
Update xfer->frlengths for input isoc transfer. Based on patches from
SOMEYA Yoshihiko.
Also fix error handling for isoc transfer somewhat; usb_transfer_complete
shouldn't be called for more than once.
date: 2002/12/07 07:14:28; author: toshii;
Fix several nits. Mostly from SOMEYA Yoshihiko.
- Call usbd_transfer_complete at splusb.
- Fix a botched for loop in ohci_rem_ed.
- In ohci_close_pipe, wait 1ms after removing an ED to avoid possible race
condition.
The splusb change is non-functional on FreeBSD.
The botched loop and race condition changes came from us.
This patch is non-functional.
date: 2002/09/29 20:58:25; author: augustss;
Add some spl calls to protect critical regions. From kern/18440,
Takeshi Nakayama.
(No functional change on FreeBSD).
date: 2002/12/31 02:21:31; author: dsainty;
Be somewhat more persuasive about enabling the port on a port reset.
USB protocol dictates that the port enable must be implied by the port
reset. To implement this on (at least) the VIA VT83C572 this means we
need to wait around tweaking the chip state until the port actually
transitions to enabled (or the device goes away). Likely fixes
kern/11018.
get a Hub descriptor, we have to set req.wValue to "Descriptor Type
and Descriptor Index". In this case, Descriptor Type is 0x29
(UDESC_HUB), Descriptor Index should be 0.
If I don't do a check (dev->address > 1 ... ), root hub fails.
A new Cytronix 4-port USB 2.0 Hub (Cypress CY7C65640 chip) now works
after this patch.
Submitted by: Alexander Pohoyda <alexander.pohoyda@gmx.net>
MFC after: 7 days
64-bit counters that wrap on overflow. They are collecte once per
second from the chips. Currently they can be retrieved via a sysctl phy_stats.
A write of an arbitrary value to the sysctl atomically retrieves the
statistics and clears them.
* Use ACPI_BUFFER as the type for AcpiGetObjectInfo
* Remove AcpiEnableEvent/AcpiClearEvent for ACPI_EVENT_FIXED (power/sleep
buttons) as they are no longer needed
* Change calls to use the new GPE functions
* Add AcpiOs*Lock functions
Even if we have no AT keyboard, an AT keyboard is registered because
it's probed with KB_CONF_PROBE_ONLY flag set during console initialization.
Unregister the keyboard if it doesn't present while second probe.
This should fix USB keyboard only case without 'kbdcontrol -k /dev/kbd1'.
(mainly the 3Com 3c996B/BCM5701).
For some reason that I don't fully understand, the 5701 signals PCS
encoding errors as though they were link change events, i.e. the 'link
state changed' bit in the status word of the status block is updated
and an interrupt is generated. This would cause the bge_tick() function
to be invoked and a "gigabit link up" message to be printed on the console.
To avoid this, the interrupt handler now checks the MAC status register
when a link change interrupt is triggered, and it will only call the
bge_tick() function if the 'PCS encoding error detected' bit is clear.
(This change should have no effect on copper NICs since this bit can
only ever be set in TBI mode. I do not know how it affects 5704 NICs
with a BCM8002 SERDES PHY.)
Special thanks to: Sherry Rogers at UCB for allowing me access to one
of their traffic monitor boxes so I could diagnose this problem.
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
* Always use polled mode. The intr approach did not work for many
controllers and required the hw.acpi.ec.event_driven workaround.
* Only use an edge (not level) triggered GPE handler
* Add sc->ec_mtx for locking operations to a single EC. There were
many race conditions earlier between an SCI event and EcRead/Write.
* Use 1 ms as the global lock timeout
* Only acquire global lock if _GLK != 0
* Update EcWaitEvent to use an incremental backoff delay in its
poll loop. Wait 50 ms max instead of 10. Most ECs respond
in < 5 us (50 us when heavily loaded). However, some time out
occasionally even with a 10 ms timeout. For delays past 1 ms, use
msleep instead of DELAY to give SCI interrupts a chance to occur.
* Add EcCommand to send a command and wait for the appropriate event.
* The hw.acpi.ec.event_driven tunable is no longer applicable and
has been removed.
Ideas from: Linux
bus_dma_tag_create. We need to be sure that our packets are
kept in-sequence (that's how ATM is supposed to work) and
therefor use BUS_DMA_NOWAIT in all calls to bus_dmamap_load.
For memory allocated with bus_dmamem_alloc the use of anything
other than NULL arguments for the locking is anyway bogus because
this memory never should need bouncing and hence the load should never
be defered.
Allow the receipt of OAM and RM cells on raw connections. Caveat: it seems
that RM cells are still processed by the hardware even when we open the
connection as UBR.
