and xmit parameters. This makes it possible to use tdma on fractional
channels.
o add IEEE80211_MODE_HALF and IEEE80211_MODE_QUARTER; note these are
band-agnostic (may need revisiting)
o setup all default rates in ic_sup_rates instead of doing it only
for active modes; we need these to calculate the default tx parameters
which are not recalculated after a regulatory update (can't just
recalculate after installing a new channel list because we might
clobber user settings)
o remove special case code in ieee80211_get_suprates; this is now
a candidate for an inline or removal
o add various entries for new modes (roaming+tx params, wme, rate
mapping, scan set setup, country ie construction, tdma, basic rates)
Note these modes are intentionally not visible through if_media.
parent interface tasks to complete. This had been added to the ioctl path but
it is also need elsewhere like detach so its safe to teardown.
Reported by: Hans Petter Selasky
Submitted by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
don't do this right; instead go to the scan cache so we pass through
auth state (if the cache is warm we can do this w/o an actual scan)
MFC after: 1 week
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
through wpa_supplcant. If a sta is deauth'd (e.g. due to inactivity)
with roaming mode set to manual then a subsequent MLME assoc request
will be incorrectly handled and the station will never reauthenticate.
To fix this interpret a reason code of zero as sufficient to send an
auth request frame.
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
the state machine clocks to INIT, node references are not reclaimed.
Add a new routine ieee80211_drain_ifq that does this and use it
instead of IF_DRAIN.
Submitted by: Sepherosa Ziehau
Obtained from: DragonFly
MFC after: 1 month
o add IEEE80211_F_JOIN flag to ieee80211_fix_rate to indicate a station
is joining a BSS; this is used to control whether or not we over-write
the basic rate bit in the calculated rate set
o fix ieee80211_fix_rate to honor IEEE80211_F_DODEL when IEEE80211_F_DONEGO
is not specified (e.g. when joining an ibss network)
o on sta join always delete unusable rates from the negotiated rate set,
this was being done only ibss networks but is also needed for 11g bss
with mixed stations
o on sta join delete unusable rates from the bss node's rate set, not the
scan table entry's rate set
o when calculating a rate set for new neighbors in an ibss caculate a
negotiated rate set so drivers are not presented with rates they should
not use
Submitted by: Sepherosa Ziehau (w/ modifications)
Obtained from: DragonFly
MFC after: 1 month
in the Public Safety Band):
o add channel flags to identify half/quarter-rate operation
o add rate sets (need to check spec on 4Mb/s in 1/4 rate)
o add if_media definitions for new rates
o split net80211 channel setup out into ieee80211_chan_init
o fixup ieee80211_mhz2ieee and ieee80211_ieee2mhz to understand half/quarter
rate channels: note we temporarily use a nonstandard/hack numbering that
avoids overlap with 2.4G channels because we don't (yet) have enough
state to identify and/or map overlapping channel sets
o fixup ieee80211_ifmedia_init so it can be called post attach and will
recalculate the channel list and associated state; this enables changing
channel-related state like the regulatory domain after attach (will be
needed for 802.11d support too)
o add ieee80211_get_suprates to return a reference to the supported rate
set for a given channel
o add 3, 4.5, and 27 MB/s tx rates to rate <-> media conversion routines
o const-poison channel arg to ieee80211_chan2mode
particular this fixes use of wme in adhoc demo mode, it wasn't possible
to set the txop limit because the aggressive mode logic would override
Reviewed by: apatti
MFC after: 2 weeks
in the 802.11 layer: we send a directed probe request frame to the
current ap bmiss_max times (w/o answer) before scanning for a new ap.
MFC after: 2 weeks
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
here but it includes completed 802.11g, WPA, 802.11i, 802.1x, WME/WMM,
AP-side power-save, crypto plugin framework, authenticator plugin framework,
and access control plugin frameowrk.
device drivers to declare that the ifp->if_start() method implemented
by the driver requires Giant in order to operate correctly.
Add a 'struct task' to 'struct ifnet' that can be used to execute a
deferred ifp->if_start() in the event that if_start needs to be called
in a Giant-free environment. To do this, introduce if_start(), a
wrapper function for ifp->if_start(). If the interface can run MPSAFE,
it directly dispatches into the interface start routine. If it can't
run MPSAFE, we're running with debug.mpsafenet != 0, and Giant isn't
currently held, the task is queued to execute in a swi holding Giant
via if_start_deferred().
Modify if_handoff() to use if_start() instead of direct dispatch.
Modify 802.11 to use if_start() instead of direct dispatch.
This is intended to provide increased compatibility for non-MPSAFE
network device drivers in the presence of Giant-free operation via
asynchronous dispatch. However, this commit does not mark any network
interfaces as IFF_NEEDSGIANT.
