Also, pass control frames to the host while in MONITOR mode and / or
when promiscuous mode is enabled.
Tested with Netgear WG111 v3 (RTL8187B), STA / MONITOR modes.
MFC after: 2 weeks
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
Enforce net80211 rates for control / management / multicast / EAPOL frames
and allow to override rate for unicast frames via ifconfig(8) 'ucastrate'
option; by default it still uses f/w rate adaptation for unicast frames.
MFC after: 1 week
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
- Check if buffer can contain Rx descriptor before accessing it.
- Verify upper / lower bounds for frame length.
- Do not pass too short frames into ieee80211_find_rxnode().
While here:
- Move cleanup to the function end.
- Reuse IEEE80211_IS_DATA() macro.
MFC after: 1 week
- Discard frames that are bigger than MCLBYTES (to prevent buffer overrun).
- Check buffer length before accessing its contents.
- Fix len <-> dmalen check - the last includes Rx Wireless information
structure size.
- Fix out-of-bounds read during Rx node search for ACK / CTS frames
(monitor mode only).
While here:
- Mark few suspicious places with comments.
- Move common cleanup to the function end.
MFC after: 1 week
Without HID_IGNORE quirk enabled these models appear in the system as a uhid
devices while NUT (Network UPS Tool) expects them to be ugen.
PR: 131521
Submitted by: Naoyuki Tai <ntai@smartfruit.com>, John Bayly <john.bayly@tipstrade.net>
MFC after: 1 week
Extend the vendor class USB audio quirk to cover devices without
the USB audio control descriptor.
PR: 234794
MFC after: 1 week
Sponsored by: Mellanox Technologies
out dead USB HUB devices by implementing an error counter, so that the USB
enumeration thread does not spend all its time reading from non-responding
devices, blocking user-space access in the end.
Tested by: Matthias Apitz <guru@unixarea.de>
MFC after: 1 week
Sponsored by: Mellanox Technologies
transaction translator will return a NAK. Ignore this message and
retry the complete split instead.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Now evdev part of keyboard drivers does not take any locks if corresponding
input/eventN device node is not opened by userland consumers.
Do not assert console lock inside evdev to handle the cases when keyboard
driver is called from some special single-threaded context like shutdown
thread.
the current fixed values, which enables use of rates above 1 Mbps.
Improved the detection of HXD chips, and the status flag handling as
well.
Submitted by: Gabor Simon <gabor.simon75@gmail.com>
PR: 225932
Differential revision: https://reviews.freebsd.org/D16639
MFC after: 1 week
Sponsored by: Mellanox Technologies
translator, when using the DWC OTG USB controller driver. Make sure to re-try
getting the complete split packets until a DATA0 packet is received. Larger
isochronous frames may be split into multiple MDATA packets terminated
by a single DATA0 packet.
PR: 230434
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
