o 3Com 3crwe62092a
o Addtron awp100
o No Wires Necessary WLAN 550 and 1148
o Proxim RANGELANDS 8340
and reorder linksys to be in proper sort order.
Obtained from: OpenBSD (mostly)
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
o Add exerpimental support for identifying lucent cards. All of mine
come back with ID of 1, but NetBSD committed code for 5. So accept
both.
o rename wi_prism2_ver to wi_firmware_ver so that we could, if necessary,
do special things for lucent cards too.
o Bring in a small part of the changes from airtools: The wi_cmd function
now takes two additional arguments. I didn't bring in their ioctls yet.
o eliminate the use of LE16TOH, and remove its define.
o Print the firmware as if there were 100 versions instead of 10. This means
that 6.1 and 6.10 aren't confusing to people. We now print 6.01 in the
former case.
# A good junior hacker project would be to merge the NetBSD, FreeBSD, and
# OpenBSD drivers into one source base.
Some buggy firmware workarounds. Fix some endian bugs.
These reduce the diffs from NetBSD, but NetBSD does have more changes since
my last manual merge.
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
prism2 flag in pccard.conf, but I'm leaving it place for the moment in
case the small sample of PrismII cards that I've tried is not
representative.
MFC After: 30 days
Obtained from: NetBSD
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
go into the PLX 9052's interrupt control register and turn on the magic
interrupt enable bit.
Partial thanks are due to OpenBSD for pointing out that the chip is a
PLX 9052 and pointing me to the datasheet PDF.
It appears that a number of PrismII card vendors seem to be doing the
same thing (that is, using the same PCI bridge chip) to support PCI,
but each with their own vendor/product ID. So rather than cut-n-paste
another if statement into the probe routine, it's probably better to
provide support for a table. Adding new devices will be a lot easier
that way.
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
a LinkSys card here in the office where reading the station address
fails the first time, but works find afterwards. Without this, the
probe fails. I don't think this will negatively impact any existing
cards, but I want to confirm this before MFC'ing.
s/1518/ETHER_MAX_LEN
Some style changes, add some braces, mostly residual from having
a lot of debug hooks added while working on this driver.
Bring in a plethora of changes from NetBSD:
revision 1.58
date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1
it wait until busy flag disappears.
it was able to prevent some cards with late initializing faling in wi_reset().
revision 1.41
date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2
Fix wi_intr() to avoid touching card registers during insert/remove events,
when sharing an interrupt with other devices:
check sc->sc_enabled, and drop the interrupt if its' off.
revision 1.30
date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4
Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header
instead of addr1 and addr2. THis means that tcpdump -e will show the
correct MAC address for communications with access points instead of showing
the BSSID.
In the future there should be 802.11 support for bpf/libpcap/tcpdump,
but that is aways down the road.
o Change the number of init tries from 5 to a #define.
o Allow up to 5s rather than 2s for commands to complete. This
is still much less than 51 minutes, but makes my intel card init
with more reliability than before.
Don't leak iospace when irq allocation fails. (call wi_free())
Call bus_release_resource() with the correct "rid" obtained from
bus_alloc_resource() that's saved in the softc instead of a hardcoded
0.
